Design and Calculation of Magnetic Liquid Seal with Rectangular Pole Teeth

2011 ◽  
Vol 492 ◽  
pp. 287-290 ◽  
Author(s):  
Xiao Long Yang ◽  
De Cai Li ◽  
Weng Ming Yang ◽  
Fei Fei Xing
Keyword(s):  
Design Process ◽  
Circuit Design ◽  
Magnetic Circuit ◽  
Design Method ◽  
Reference Value ◽  
Magnetic Liquid ◽  
Liquid Seal ◽  
Sealing Device ◽  
Kirchhoff's Law

The principle of magnetic liquid seal with rectangular pole teeth structure is discussed in this paper, and the magnetic circuit design process of magnetic liquid seal with rectangular pole teeth structure is systematically discussed. Using the formula of pressure capability of magnetic liquid seal with rectangular pole teeth structure and equivalent magnetic circuit, the magnetic circuit of magnetic liquid seal with rectangular pole teeth structure was designed and calculated in detail according to the kirchhoff's law of the magnetic circuit. The design method of magnetic circuit in magnetic liquid seal with rectangular pole teeth structure proposed in this paper has important reference value to the design of magnetic liquid sealing device.

scholarly journals Magnetic Circuit Design and Finite Element Simulation Analysis of Magnetic Fluid Rotating Dynamic Sealing Device

CONVERTER ◽  
2021 ◽  
pp. 658-663
Author(s):  
Xiaojuan Li Et al.
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Circuit Design ◽  
Magnetic Fluid ◽  
Magnetic Circuit ◽  
Test Method ◽  
Element Simulation ◽  
Tooth Width ◽  
Dynamic Seal ◽  
Sealing Device

The magnetic fluid rotary dynamic sealing device is based on the magnetic fluid material. The typical sealing structure is to fill the magnetic fluid in the gap between the shaft and the magnetic pole, and keep it in the sealing gap under the action of the external magnetic field to form a liquid "O"-shaped sealing ring to block it. The sealing effect of this kind of device largely depends on the design of the magnetic circuit structure of the device. In this paper, ANSYS finite element simulation is used to analyze the influence of seal stages, tooth shape and the number of permanent magnets on the magnetic fluid rotating dynamic seal. The L9 (34) factor level table is designed by orthogonal test method to analyze the priority of the influence of tooth width, seal clearance and chamfering on the magnetic fluid sealing performance, which provides the reference for the structural design and magnetic circuit design of magnetic fluid rotating dynamic seal.

Development of the design method for the optimal design of the Neutron Converter experimental plant

2020 ◽  
Author(s):  
Timur Smetani ◽  
Elizaveta Gureva ◽  
Vyacheslav Andreev ◽  
Natalya Tarasova ◽  
Nikolai Andree
Keyword(s):  
Optimal Design ◽  
Flux Density ◽  
Design Process ◽  
Design Method ◽  
Fast Neutrons ◽  
Experimental Plant ◽  
Plant Design ◽  
State Technical ◽  
Research Organizations ◽  
Neutron Converter

The article discusses methods for optimizing the design of the Neutron Converter research plant design with parameters that are most suitable for a particular consumer. 38 similar plant structures with different materials and sources were calculated, on the basis of which the most optimal options were found. As part of the interaction between OKBM Afrikantov JSC and the Nizhny Novgorod State Technical University named after R. E. Alekseev, the Neutron Converter research plant was designed and assembled. The universal neutron converter is a device for converting a stream of fast neutrons emitted by isotopic sources into a "standardized" value of flux density with known parameters in the volume of the central part of the product, which is the working part of the universal neutron converter. To supply neutron converters to other customer organizations (universities, research organizations and collective centers), it is necessary to take into account the experience of operating an existing facility, as well as rationalize the design process of each specific instance in accordance with the requirements of the customer.

The design of modular oil tank: A new design process model

2020 ◽  
Vol 15 ◽  
Author(s):  
Jin Li ◽  
Xingsheng Jiang ◽  
Jingye Li ◽  
Yadong Zhao ◽  
Xuexing Li
Keyword(s):  
Product Design ◽  
Design Process ◽  
Process Model ◽  
Mechanical Design ◽  
Computer Software ◽  
Reference Value ◽  
Fuel Tank ◽  
Design Quality ◽  
Design Time ◽  
Design Process Model

Background: In the whole design process of modular fuel tank, there are some unreasonable phenomena. As a result, there are some defects in the design of modular fuel tank, and the function does not meet the requirements in advance. This paper studies this problem. Objective: Through on-the-spot investigation of the factory, a mechanical design process model is designed. The model can provide reference for product design participants on product design time and design quality, and can effectively solve the problem of low product design quality caused by unreasonable product design time arrangement. Methods: After sorting out the data from the factory investigation, computer software is used to program, simulate the information input of mechanical design process, and the final reference value is got. Results: This mechanical design process model is used to guide the design and production of a new project, nearly 3 months ahead of the original project completion time. Conclusion: This mechanical design process model can effectively guide the product design process, which is of great significance to the whole mechanical design field.

scholarly journals Development of Optimal Design Method for Steel Double-Beam Floor System Considering Rotational Constraints

2021 ◽  
Vol 11 (7) ◽  
pp. 3266
Author(s):  
Insub Choi ◽  
Dongwon Kim ◽  
Junhee Kim
Keyword(s):  
Optimal Design ◽  
Design Process ◽  
Design Method ◽  
Steel Beams ◽  
High Gravity ◽  
Double Beam ◽  
Iterative Analysis ◽  
Floor Systems ◽  
Optimal Design Method ◽  
Floor System

Under high gravity loads, steel double-beam floor systems need to be reinforced by beam-end concrete panels to reduce the material quantity since rotational constraints from the concrete panel can decrease the moment demand by inducing a negative moment at the ends of the beams. However, the optimal design process for the material quantity of steel beams requires a time-consuming iterative analysis for the entire floor system while especially keeping in consideration the rotational constraints in composite connections between the concrete panel and steel beams. This study aimed to develop an optimal design method with the LM (Length-Moment) index for the steel double-beam floor system to minimize material quantity without the iterative design process. The LM index is an indicator that can select a minimum cross-section of the steel beams in consideration of the flexural strength by lateral-torsional buckling. To verify the proposed design method, the material quantities between the proposed and code-based design methods were compared at various gravity loads. The proposed design method successfully optimized the material quantity of the steel double-beam floor systems without the iterative analysis by simply choosing the LM index of the steel beams that can minimize objective function while satisfying the safety-related constraint conditions. In particular, under the high gravity loads, the proposed design method was superb at providing a quantity-optimized design option. Thus, the proposed optimal design method can be an alternative for designing the steel double-beam floor system.

Impact of Secondary Flow on the Accuracy of Simplified Design Methods for Steam Turbine Stages

2012 ◽  
Author(s):  
Jan Schumann ◽  
Ulrich Harbecke ◽  
Daniel Sahnen ◽  
Thomas Polklas ◽  
Peter Jeschke ◽  
...  
Keyword(s):  
Secondary Flow ◽  
Steam Turbine ◽  
Design Process ◽  
Design Method ◽  
Computing Time ◽  
Leading Edge ◽  
Design Methods ◽  
Preliminary Design ◽  
Line Design ◽  
Radial Equilibrium

The subject of the presented paper is the validation of a design method for HP and IP steam turbine stages. Common design processes have been operating with simplified design methods in order to quickly obtain feasible stage designs. Therefore, inaccuracies due to assumptions in the underlying methods have to be accepted. The focus of this work is to quantify the inaccuracy of a simplified design method compared to 3D Computational Fluid Dynamics (CFD) simulations. Short computing time is very convenient in preliminary design; therefore, common design methods work with a large degree of simplification. The origin of the presented analysis is a mean line design process, dealing with repeating stage conditions. Two features of the preliminary design are the stage efficiency, based on loss correlations, and the mechanical strength, obtained by using the beam theory. Due to these simplifications, only a few input parameters are necessary to define the primal stage geometry and hence, the optimal design can easily be found. In addition, by using an implemented law to take the radial equilibrium into account, the appropriate twist of the blading can be defined. However, in comparison to the real radial distribution of flow angles, this method implies inaccuracies, especially in regions of secondary flow. In these regions, twisted blades, developed by using the simplified radial equilibrium, will be exposed to a three-dimensional flow, which is not considered in the design process. The analyzed design cases show that discrepancies at the hub and shroud section do exist, but have minor effects. Even the shroud section, with its thinner leading-edge, is not vulnerable to these unanticipated flow angles.

A CMOS combinational circuit-design method using mixed logic concepts

1995 ◽  
Vol 38 (3) ◽  
pp. 266-273 ◽  
Author(s):  
W.B. Hudson ◽  
J.S. Beasley ◽  
J.E. Steelman
Keyword(s):  
Circuit Design ◽  
Design Method ◽  
Combinational Circuit
Sign in / Sign up

Export Citation Format

Share Document