Development of the design method for the optimal design of the Neutron Converter experimental plant

2020 ◽  
Author(s):  
Timur Smetani ◽  
Elizaveta Gureva ◽  
Vyacheslav Andreev ◽  
Natalya Tarasova ◽  
Nikolai Andree
Keyword(s):  
Optimal Design ◽  
Flux Density ◽  
Design Process ◽  
Design Method ◽  
Fast Neutrons ◽  
Experimental Plant ◽  
Plant Design ◽  
State Technical ◽  
Research Organizations ◽  
Neutron Converter

The article discusses methods for optimizing the design of the Neutron Converter research plant design with parameters that are most suitable for a particular consumer. 38 similar plant structures with different materials and sources were calculated, on the basis of which the most optimal options were found. As part of the interaction between OKBM Afrikantov JSC and the Nizhny Novgorod State Technical University named after R. E. Alekseev, the Neutron Converter research plant was designed and assembled. The universal neutron converter is a device for converting a stream of fast neutrons emitted by isotopic sources into a "standardized" value of flux density with known parameters in the volume of the central part of the product, which is the working part of the universal neutron converter. To supply neutron converters to other customer organizations (universities, research organizations and collective centers), it is necessary to take into account the experience of operating an existing facility, as well as rationalize the design process of each specific instance in accordance with the requirements of the customer.

scholarly journals Development of Optimal Design Method for Steel Double-Beam Floor System Considering Rotational Constraints

2021 ◽  
Vol 11 (7) ◽  
pp. 3266
Author(s):  
Insub Choi ◽  
Dongwon Kim ◽  
Junhee Kim
Keyword(s):  
Optimal Design ◽  
Design Process ◽  
Design Method ◽  
Steel Beams ◽  
High Gravity ◽  
Double Beam ◽  
Iterative Analysis ◽  
Floor Systems ◽  
Optimal Design Method ◽  
Floor System

Under high gravity loads, steel double-beam floor systems need to be reinforced by beam-end concrete panels to reduce the material quantity since rotational constraints from the concrete panel can decrease the moment demand by inducing a negative moment at the ends of the beams. However, the optimal design process for the material quantity of steel beams requires a time-consuming iterative analysis for the entire floor system while especially keeping in consideration the rotational constraints in composite connections between the concrete panel and steel beams. This study aimed to develop an optimal design method with the LM (Length-Moment) index for the steel double-beam floor system to minimize material quantity without the iterative design process. The LM index is an indicator that can select a minimum cross-section of the steel beams in consideration of the flexural strength by lateral-torsional buckling. To verify the proposed design method, the material quantities between the proposed and code-based design methods were compared at various gravity loads. The proposed design method successfully optimized the material quantity of the steel double-beam floor systems without the iterative analysis by simply choosing the LM index of the steel beams that can minimize objective function while satisfying the safety-related constraint conditions. In particular, under the high gravity loads, the proposed design method was superb at providing a quantity-optimized design option. Thus, the proposed optimal design method can be an alternative for designing the steel double-beam floor system.

scholarly journals GENERATIVE DESIGN OF STRUCTURAL STEEL JOINTS

2021 ◽  
Vol 12 (23) ◽  
pp. 22-32
Author(s):  
Anton Kralj ◽  
◽  
Davor Skejić ◽  
Keyword(s):  
Optimal Design ◽  
Design Process ◽  
Structural Design ◽  
Design Method ◽  
Steel Structures ◽  
Structure Design ◽  
Structural Behavior ◽  
Generative Design ◽  
Steel Joints ◽  
Technical Regulations

Structural project is based on technical regulations, structural codes, construction conditions, and client requirements. Through the structural design process, some important decisions that can significantly affect the final result must be implemented. The most important factor for optimal design is the reduction in material and overall work costs. Selecting appropriate joint configurations that can reduce the overall weight and work on the structure is critical. To examine a significant number of possible configurations and their effect on structural behavior, the generative design method (GDM) is used. In this study, software is custom developed, and a relevant example of generative joint structural design is provided. The methodology for the optimal joint and structure design is described comprehensively. The final results show that the GDM is an effective methodology for application in the design of steel structures.

An Optimal Missile Autopilot Design Model

2018 ◽  
Vol 14 (1) ◽  
pp. 104-110
Author(s):  
Yong-chao Chen ◽  
Xin-bao Gao ◽  
Min Gao ◽  
Dan Fang
Keyword(s):  
Optimal Design ◽  
Objective Function ◽  
Design Process ◽  
Objective Function Value ◽  
Design Method ◽  
Response Speed ◽  
Performance Indexes ◽  
Optimal Design Method ◽  
Objective Function Values ◽  
Constrained Conditions

This article describes how one optimal design method is given to the design of missile autopilots. This method profits from an exhaustive method. By this method, the design process of a missile autopilot is simplified, and the design efficiency is improved. In the design process of this method, the performance indexes of autopilot are translated into constraint conditions, and the response speed is translated to an objective function. Thus, the optimal design of missile autopilot is translated into the optimal design of a nonlinear system with multiple constraints. The optimization algorithm is found to be out of controller parameter combinations which can satisfy constrained conditions. Firstly, calculations of the corresponding objective function values. Second, by the extract the optimal combination which has the minimal objective function value.

scholarly journals A Two-Round Optimization Design Method for Aerostatic Spindles Considering the Fluid–Structure Interaction Effect

2021 ◽  
Vol 11 (7) ◽  
pp. 3017
Author(s):  
Qiang Gao ◽  
Siyu Gao ◽  
Lihua Lu ◽  
Min Zhu ◽  
Feihu Zhang
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Design Method ◽  
Fluid Structure Interaction ◽  
Design Procedure ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Aerostatic Spindle

The fluid–structure interaction (FSI) effect has a significant impact on the static and dynamic performance of aerostatic spindles, which should be fully considered when developing a new product. To enhance the overall performance of aerostatic spindles, a two-round optimization design method for aerostatic spindles considering the FSI effect is proposed in this article. An aerostatic spindle is optimized to elaborate the design procedure of the proposed method. In the first-round design, the geometrical parameters of the aerostatic bearing were optimized to improve its stiffness. Then, the key structural dimension of the aerostatic spindle is optimized in the second-round design to improve the natural frequency of the spindle. Finally, optimal design parameters are acquired and experimentally verified. This research guides the optimal design of aerostatic spindles considering the FSI effect.

Impact of Secondary Flow on the Accuracy of Simplified Design Methods for Steam Turbine Stages

2012 ◽  
Author(s):  
Jan Schumann ◽  
Ulrich Harbecke ◽  
Daniel Sahnen ◽  
Thomas Polklas ◽  
Peter Jeschke ◽  
...  
Keyword(s):  
Secondary Flow ◽  
Steam Turbine ◽  
Design Process ◽  
Design Method ◽  
Computing Time ◽  
Leading Edge ◽  
Design Methods ◽  
Preliminary Design ◽  
Line Design ◽  
Radial Equilibrium

The subject of the presented paper is the validation of a design method for HP and IP steam turbine stages. Common design processes have been operating with simplified design methods in order to quickly obtain feasible stage designs. Therefore, inaccuracies due to assumptions in the underlying methods have to be accepted. The focus of this work is to quantify the inaccuracy of a simplified design method compared to 3D Computational Fluid Dynamics (CFD) simulations. Short computing time is very convenient in preliminary design; therefore, common design methods work with a large degree of simplification. The origin of the presented analysis is a mean line design process, dealing with repeating stage conditions. Two features of the preliminary design are the stage efficiency, based on loss correlations, and the mechanical strength, obtained by using the beam theory. Due to these simplifications, only a few input parameters are necessary to define the primal stage geometry and hence, the optimal design can easily be found. In addition, by using an implemented law to take the radial equilibrium into account, the appropriate twist of the blading can be defined. However, in comparison to the real radial distribution of flow angles, this method implies inaccuracies, especially in regions of secondary flow. In these regions, twisted blades, developed by using the simplified radial equilibrium, will be exposed to a three-dimensional flow, which is not considered in the design process. The analyzed design cases show that discrepancies at the hub and shroud section do exist, but have minor effects. Even the shroud section, with its thinner leading-edge, is not vulnerable to these unanticipated flow angles.

A Displacement-Based Optimal Design Method of RC Frames Subjected to Minor Earthquakes

2012 ◽  
Vol 594-597 ◽  
pp. 795-799
Author(s):  
Gui Tao Chen ◽  
De Min Wei
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Virtual Work ◽  
Design Method ◽  
Horizontal Displacement ◽  
Target Displacement ◽  
Programming Technique ◽  
Direct Displacement Based Design ◽  
Rc Frames ◽  
Displacement Based

A displacement-based optimization design method of RC structure was proposed by combining direct displacement-based design method with nonlinear programming technique. To avert the influence of target displacement, the stationary constraint displacement was presented, and the target displacement can be updated during the optimal design process. Principle of virtual work and Gaussian integral method was employed to simplify the explicit relationship between horizontal displacement and the section dimension. Comparison analysis of the local optimal results corresponding to different displacement shapes was conducted to achieve global optimal design. The numerical tests presented demonstrate the computational advantages of the discussed methods and suggesting that the proposed method is a reliably and efficiently tool for displacement-based optimal design.

Development of High-Speed Response Electromagnetic Linear Actuator Using for Pneumatic Control Valve

2014 ◽  
Vol 532 ◽  
pp. 41-45 ◽  
Author(s):  
Myung Jin Chung
Keyword(s):  
Optimal Design ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Design Method ◽  
Control Valve ◽  
Design Parameters ◽  
Linear Actuator ◽  
Analytic Model ◽  
Electromagnetic Linear Actuator ◽  
Quadratic Programming Method

Analytic model of electromagnetic linear actuator in the function of electric and geometric parameters is proposed and the effects of the design parameters on the dynamic characteristics are analyzed. To improve the dynamic characteristics, optimal design is conducted by applying sequential quadratic programming method to the analytic model. This optimal design method aims to minimize the response time and maximize force efficiency. By this procedure, electromagnetic linear actuator having high-speed characteristics is developed.

Sign in / Sign up

Export Citation Format

Share Document