Properties of Dan Kwian, Sukhothai and Ratchaburi Pottery Clays Fired at 700 and 900 °C

2014 ◽  
Vol 608 ◽  
pp. 47-61
Author(s):  
Nonglak Meethong ◽  
Wanwisa Pattanasiriwisawa ◽  
Weenawan Somphon ◽  
Waraporn Tanthanuch ◽  
Sutham Srilomsak
Keyword(s):  
Specific Gravity ◽  
Comparative Study ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Reflectance Spectra ◽  
Modulus Of Rupture ◽  
Regression Equations ◽  
Statistical Software

Dan Kwian, Sukhothai and Ratchaburi pottery clays are economically important pottery clays. They are well known in the Thai ceramic society for making Dan Kwian pottery, Sawankhalok pottery and Dragon jars, respectively. There have been several studies of these pottery clays. However, few of them used statistics to analyze their results. This work is a comparative study of the compositions and properties of these three pottery clays using statistical software to analyze the results. Results show that the major components of these pottery clays are SiO2 and Al2O3. The Modulus of Rupture (MOR) of each pottery clay fired at 700°C are not significantly different. Sukhothai pottery clay fired at 900°C has a higher MOR and bulk density while its porosity, water absorption and apparent specific gravity are less than those of the Dan Kwian and Ratchaburi pottery clays fired at the same temperature. Additionally, the current study developed regression equations for estimating the properties of all pottery clays under study. Finally, it was found that the L*, a*, b* and reflectance spectra of all pottery clays increased when firing temperature was increased from 700 to 900°C.

scholarly journals Optimisation of the Physical Properties of Rice Husk Ash in Ceramic Materials Using the Response Surface Methodology

2021 ◽  
Vol 49 (1) ◽  
pp. 23-30
Author(s):  
Asotah Wisdom ◽  
Udochukwu Mark ◽  
Elakhame Zeberu ◽  
Abraham Adeleke
Keyword(s):  
Response Surface Methodology ◽  
Specific Gravity ◽  
Physical Properties ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Rice Husk Ash ◽  
Ceramic Materials ◽  
Linear Shrinkage ◽  
Apparent Porosity

Optimisation of the physical properties of rice husk ash (RHA) in ceramic materials was carried out using Response Surface Methodology. The independent variables, namely the firing temperature and residue content, were statistically combined in a Central Composite Design with the effects on water absorption, linear shrinkage, bulk density, apparent porosity and apparent specific gravity determined. Physical and microstructural analyses were carried out to obtain information on the processes that occurred within the ceramic materials. The results obtained were analysed to determine the optimum physical properties of the ceramic materials within the range investigated. The residue content had a significant influence (at 95% confidence level) on the bulk density, water absorption, apparent porosity and apparent specific gravity but not on the linear shrinkage. The firing temperature had a more significant effect on the linear shrinkage than on the residue content, so that when elevated it contributed to an increase in linear shrinkage. The optimum residue content and firing temperature to enhance physical properties within the range investigated were 5.85% RHA and 1029.64°celsius, respectively. These optimal conditions are expected to produce a ceramic material with a bulk density, linear shrinkage, apparent porosity, water absorption and apparent specific gravity of 1.64 g/cm3, 0.29%, 0.29 g/cm3, 18.26% and 2.11, respectively with a composite desirability of 100%.

scholarly journals Effect of Different Extrusion Processing Parameters on Physical Properties of Soy White Flakes and High Protein Distillers Dried Grains-Based Extruded Aquafeeds

2014 ◽  
Vol 3 (6) ◽  
pp. 107 ◽  
Author(s):  
Sushil K. Singh ◽  
K. Muthukumarappan
Keyword(s):  
Physical Properties ◽  
Water Absorption ◽  
Bulk Density ◽  
Water Solubility ◽  
Expansion Ratio ◽  
High Protein ◽  
Regression Equations ◽  
Process Variables ◽  
Distillers Dried Grains ◽  
Durability Index

<p>Nutritionally balanced ingredient blends for catla (<em>Catla catla</em>), belonging to the family Cyprinidae, were extruded using single screw extruder. The extrusion was carried out at five levels of soy white flakes content (21%, 29%, 40%, 52%, and 59% db), five levels of moisture content (15, 19, 25, 31, and 35% db) and five levels of barrel temperature (100, 110, 125, 140, and 150 ºC) using three different die nozzles (having L/D ratios 3.33, 5.83, and 7.25). Blends with net protein content of 32.5% contains soy white flakes, along with high protein distillers dried grains (HP-DDG), corn flour, corn gluten meal, fish meal, vitamin, and mineral mix. A central composite rotatable design (CCRD) and  response surface methodology (RSM) was used to investigate the significance of independent and interaction effects of the extrusion process variables on the extrudates physical properties namely pellet durability index, bulk density, water absorption and solubility indices and expansion ratio. Quadratic polynomial regression equations were developed to correlate the product responses and process variables as well as to obtain the response surfaces plots. The independent variables had significant (<em>P </em>&lt; 0.05) effects on physical properties of extrudates: (i) higher soy white flakes content increased the pellet durability index and water absorption index, but decreased the water solubility index, (ii) higher temperature decreased pellet durability index, bulk density and water solubility index, (iii) increased L/D ratio from 3.33 to 7.25 increased the pellet durability index, expansion ratio but decreased the bulk density of the extrudates.</p>

Mechanical Properties and Thermal Conductivity of Lightweight Clay Bricks Fabricated with a Powdered Marble Dust Additive

2018 ◽  
Vol 777 ◽  
pp. 465-470
Author(s):  
Sutas Janbuala ◽  
Mana Eambua ◽  
Arpapan Satayavibul ◽  
Watcharakhon Nethan
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Apparent Porosity ◽  
Clay Brick ◽  
Clay Bricks ◽  
Marble Dust

The objective of this study was to recycle powdered marble dust to improve mechanical properties and thermal conductivity of lightweight clay bricks. Varying amounts of powdered marble dust (10, 20, 30, and 40 vol.%) were added to a lightweight clay brick at the firing temperatures of 900, 1000, and 1100 °C. When higher quantities of powdered marble dust were added, the values of porosity and water absorption increased while those of thermal conductivity and bulk density decreased. The decrease in apparent porosity and water absorption were also affected by the increase in firing temperature. The most desirable properties of the clay bricks were obtained for the powdered marble dust content of 40 vol.% and firing temperature 900 °C: bulk density of 1.20 g/cm3, compressive strength 9.2 MPa, thermal conductivity 0.32 W/m.K, and water absorption 22.5%.

Utilization of Glass Cutting Sludge and Sanitary Ware Sludge in Ceramic Pressed Bodies

2015 ◽  
Vol 659 ◽  
pp. 169-174 ◽  
Author(s):  
Apirat Theerapapvisetpong ◽  
Siripan Nilpairach
Keyword(s):  
Flexural Strength ◽  
Water Absorption ◽  
Firing Temperature ◽  
Soda Lime ◽  
Sanitary Ware ◽  
Production Costs ◽  
Modulus Of Rupture ◽  
Soda Lime Glass ◽  
Firing Shrinkage ◽  
Glass Cutting

Ceramic manufacturers are finding the way to decrease firing temperature and recover their wastes in order to keep production costs down. In this study earthenware ceramic bodies were prepared by adding a soda-lime glass grinding effluent powder (dried sludge) as a fluxing agent at 0–50 wt.% into either sanitary ware sludge powder (from a sanitary ware manufacturing process) or fresh pottery clay from Ang-thong, Thailand. The dried and pressed mixtures were fired at 1100, 1125 and 1150 °C and tested for the firing shrinkage, modulus of rupture, water absorption and bulk density. The formed product microstructure was observed by the scanning electron microscopy, and the phase composition was characterized by X-ray diffractometer. The results revealed that the best condition for adding the glass powder in Ang-thong pottery clay was the inclusion of 10 wt.% soda-lime glass effluent powder in the pottery clay. Its flexural strength increased from 51.25 MPa to 93.40 MPa after firing at 1125 °C with the water absorption of 0.42 wt.% and the firing shrinkage of 10.25 %. The optimum firing temperature and soda-lime glass content in sanitary ware sludge were 1150 °C and 20 wt.%, respectively. Its flexural strength increased from 103.16 MPa to 118.16 MPa with the water absorption of 0.52 wt.% and the firing shrinkage of 13.67 %. The results illustrated the potential to use soda-lime glass cutting sludge and sanitary ware sludge as raw materials for earthenware ceramic body.

Utilization of Iron Tailings for High Strength Fired Brick

2012 ◽  
Vol 550-553 ◽  
pp. 2373-2377
Author(s):  
Wei Juan Guo ◽  
Gao Xiang Du ◽  
Ran Fang Zuo ◽  
Jing Hui Liao
Keyword(s):  
Phase Composition ◽  
Mechanical Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Glass Phase ◽  
High Strength ◽  
Optimum Conditions ◽  
Crystalline Phases ◽  
Fired Bricks

his paper studies the feasibility of preparation high strength fired bricks from iron tailings with addition of clay and coal gangue. The results indicated that the optimum conditions were found to be that the hematite tailings content were 35%–50%; the firing temperature was 1000 °C. Under these conditions, the mechanical strength, the water absorption and the bulk density of the fired bricks were 21.17–26.14 MPa, 14.55–15.47% and 1.648–1.629g/cm3, respectively, these were well conformed to standards MU20 of Chinese Fired Common Bricks Standard (GB/T5101-2003).The phase composition and microstructure of the fired specimen were characterized by XRD and SEM. The results showed that the major crystalline phases present in fired brick were quartz, albite, amphibole, hematite and muscovite, and glass phase encapsulated and cement the crystalline phases forming strong entirety which promoted the strength of bricks.

Limestone Sludge in the Brick Body

2014 ◽  
Vol 1000 ◽  
pp. 158-161 ◽  
Author(s):  
Radomír Sokolař ◽  
Lucie Vodová ◽  
Mikuláš Šveda
Keyword(s):  
Thermal Conductivity ◽  
Water Absorption ◽  
Bulk Density ◽  
Quartz Sand ◽  
Modulus Of Rupture ◽  
Firing Process ◽  
Brick Clay ◽  
Coefficient Of Thermal Conductivity ◽  
Washing Process ◽  
Firing Shrinkage

Influence of limestone sludge (generated during the washing process of limestone crushed aggregates) with high content of CaO in the form of calcite on the properties of brick body made from non-calcareous sludge (from the washing process of quartz sand) as a basic plastic brick clay was determined. Presence of calcite very distinctly influenced the firing process and properties of fired body. Limestone sludge decreases firing shrinkage, bulk density and coefficient of thermal conductivity of the brick body after the firing in the range of 850 – 950 °C. Higher modulus of rupture and water absorption is typical for fired bodies with limestone sludge addition. Most of these improvement are caused by the formation of anorthite only in the bodies based on the limestone sludge.

Sign in / Sign up

Export Citation Format

Share Document