Effects of Thermomechanical Processing on Microstructure and Mechanical Properties Multiphase Steels Exhibiting a TRIP Effect

2007 ◽  
Vol 539-543 ◽  
pp. 4357-4362 ◽  
Author(s):  
Jiří Kliber ◽  
Gabriela Plestilova ◽  
Ondrej Zacek ◽  
Mahesh C. Somani
Keyword(s):  
Mechanical Properties ◽  
Hot Rolling ◽  
Trip Steel ◽  
Transformation Temperature ◽  
Retained Austenite ◽  
Thermomechanical Processing ◽  
Rolling Temperature ◽  
Bainitic Transformation ◽  
Bainite Transformation ◽  
Microstructure And Mechanical Properties

Effects of hot-rolling conditions on these steels are much less studied than their importance for practice would suggest. It should be emphasized that bainite transformation is the key reaction to enrich non-transformed austenite with carbon. This study was carried out in order to gain understanding of the effect of thermomechanical hot rolling on final microstructure and mechanical properties of C-Mn-Si TRIP steel. Fundamental of the transformation induced plasticity effect – TRIP is the stabilization of substantial amount of retained austenite down to the ambient temperature by thermomechanical processing and its subsequent transformation into strain induced martensite as a consequence of applied plastic deformation. The special prepared stepped specimens were rolled on laboratory tandem mill. The effects of finish rolling temperature, strain and isothermal bainite transformation temperature on mechanical properties of mentioned TRIP steel were evaluated (mechanical properties were examined with tension test). Major deformation, higher finishing rolling temperature and higher temperature of bainite hold result in drop in strength. Proportionately to the drop in strength, the ductility grows in the TRIP steel. Microstructures were examined with X-ray diffraction (retained austenite). Image analysis software was used to process SEM micrographs of structure (ferrite, bainite assessment). Plastometric testing was conducted on GLEEBLE 3800 thermo-mechanical simulator. First stage of experiment yielded stress-strain curves for various temperatures and strain rates. Gleeble 1500 was used for the remaining plastometric simulation. Specimens were reheated to austenitization temperature of 1100°C and soaked. Then they were cooled to the temperature of deformation and subsequently cooled at higher rate down to the bainitic transformation temperature (400 – 550 °C). Specimens were held at the bainitic transformation temperature and then air-cooled. Final microstructures were evaluated with respect to transformation diagrams and optical microscopy findings. Higher bainite volume fraction was found in the specimens cooled at higher cooling rate as compared with more slowly cooled specimens.

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

2018 ◽  
Vol 941 ◽  
pp. 329-333 ◽  
Author(s):  
Jiang Ying Meng ◽  
Lei Jie Zhao ◽  
Fan Huang ◽  
Fu Cheng Zhang ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Isothermal Treatment ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Microstructure And Mechanical Properties

In the present study, the effects of ausforming on the bainitic transformation, microstructure and mechanical properties of a low-carbon rich-silicon carbide-free bainitic steel have been investigated. Results show that prior ausforming shortens both the incubation period and finishing time of bainitic transformation during isothermal treatment at a temperature slightly above the Mspoint. The thicknesses of bainitic ferrite laths are reduced appreciably by ausforming; however, ausforming increases the amount of large blocks of retained austenite/martenisite and decreases the volume fraction of retained austenite. And accordingly, ausforming gives rise to significant increases in both yield and tensile strengths, but causes noticeable decreases in ductility and impact toughness.

scholarly journals Influence of Prior Martensite on Bainite Transformation, Microstructures, and Mechanical Properties in Ultra-Fine Bainitic Steel

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 527 ◽  
Author(s):  
Hui Guo ◽  
Xianying Feng ◽  
Aimin Zhao ◽  
Qiang Li ◽  
Jun Ma
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Bainitic Ferrite ◽  
Growth Direction ◽  
Bainitic Transformation ◽  
Bainitic Steel ◽  
Bainite Transformation ◽  
Multiphase Microstructure ◽  
Microstructures And Mechanical Properties ◽  
The Impact

A multiphase microstructure comprising of different volume fractions of prior martensite and ultra-fine bainite (bainitic ferrite and retained austenite) was obtained by quenching to certain temperatures, followed by isothermal bainitic transformation. The effect of the prior martensite transformation on the bainitic transformation behavior, microstructures, and mechanical properties were discussed. The results showed that the prior martensite accelerated the subsequent low-temperature bainite transformation, and the incubation period and completion time of the bainite reaction were significantly shortened. This phenomenon was attributed to the enhanced nucleation ratio caused by the introduced strain in austenite, due to the formation of prior martensite and a carbon partitioning between the prior martensite and retained austenite. Moreover, the prior martensite could influence the crystal growth direction of bainite ferrite, refine bainitic ferrite plates, and reduce the dimension of blocky retained austenite, all of which were responsible for improving the mechanical properties of the ultra-fine bainitic steel. When the content of the prior martensite reached 15%, the investigated steels had the best performance, which were 1800 MPa and 21% for the tensile strength and elongation, respectively. Unfortunately, the increased content of the prior martensite could lead to a worsening of the impact toughness.

scholarly journals Influence of Rolling Temperatures on Interface Microstructure and Mechanical Properties of Multi-Pass Rolling TA1/Q235B Explosive Welded Sheets

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1654
Author(s):  
Huizhong Li ◽  
Liangming Cao ◽  
Xiaopeng Liang ◽  
Wending Zhang ◽  
Chunping Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Hot Rolling ◽  
Transition Layer ◽  
Rolling Temperature ◽  
Rolled Sheet ◽  
Interface Microstructure ◽  
Microstructure And Mechanical Properties ◽  
Rolling Temperatures

The effect of rolling temperatures on the interface microstructure and mechanical properties is investigated using 2-mm-thick TA1/Q235B composite sheets, which were prepared after nine passes of hot rolling of explosive welded plates. The results show that the vortex region and the transition layer exist in the interface at the explosive welded plate, while only the transition layer exists in the interface after hot rolling. The transition layer is composed of α-Ti, TiC, Fe, and FeTi, and the thickness increases with the increasing rolling temperature. The microhardness of the explosive welded plate is higher than that of the hot-rolling sheet, and the microhardness of interface are higher than that of matrix metals. The interface shear strength and tensile elongation of the hot-rolled sheet increase with the increasing hot rolling temperature, while the ultimate tensile strength (UTS), yield strength (YS) and Young modulus decrease with the increase of hot rolling temperature. The shear strength of sheets is related to the interfacial compounds, and the tensile strength is mainly affected by the grain morphology of the matrix.

scholarly journals EFFECT OF C-Mn PARTITIONING ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TRIP STEEL

2021 ◽  
Vol 55 (2) ◽  
pp. 269-275
Author(s):  
Cainian Jing ◽  
Qiteng Lei ◽  
Tao Lin ◽  
Daomin Ye ◽  
Cong Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Lath Martensite ◽  
Tensile Tests ◽  
Microstructure And Mechanical Properties

In this paper, the TRIP590 steel was used for C-Mn partitioning. The influence of C-Mn partitioning on the microstructure and mechanical properties of the steel was studied. SEM, EPMA, XRD and tensile tests were used to characterize the microstructure of the tested steel, calculate the content of retained austenite, and analyze the enrichment of C atoms and Mn atoms and mechanical properties. The results show that there was a lot of lath martensite and scattered ferrite in the microstructures of the Q&P steel and C-Mn partitioning steel. After C-Mn partitioning, the content of ferrite was increased. The enrichment of C and Mn in the C-Mn partitioning steel was relatively apparent, and the concentration of the atoms in the center of martensite was significantly higher than at the boundary between martensite and ferrite. Mn-rich areas were also C-rich areas. Compared with the Q&P steel, the C-Mn partitioning steel had a larger amount of retained austenite, higher elongation and PSE.

Effects of Isothermal Bainite Transformation on Stability of Retained Austenite and Mechanical Properties of CMnAl-TRIP Steel

2019 ◽  
Vol 46 (11) ◽  
pp. 1102004
Author(s):  
黄慧强 Huang Huiqiang ◽  
邸洪双 Di Hongshuang ◽  
张天宇 Zhang Tianyu ◽  
闫宁 Yan Ning ◽  
龚殿尧 Gong Dianyao
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Bainite Transformation

scholarly journals The Impact of Retained Austenite on the Mechanical Properties of Bainitic and Dual Phase Steels

2022 ◽  
Author(s):  
Bogusława Adamczyk-Cieślak ◽  
Milena Koralnik ◽  
Roman Kuziak ◽  
Kamil Majchrowicz ◽  
Tomasz Zygmunt ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Transformation Temperature ◽  
Retained Austenite ◽  
Tensile Tests ◽  
Total Elongation ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Bainitic Steel ◽  
Continuous Cooling

AbstractThis paper presents the microstructural changes and mechanical properties of carbide-free bainitic steel subjected to various heat treatment processes and compares these results with similarly treated ferritic–pearlitic steel. A key feature of the investigated steel, which is common among others described in the literature, is that the Si content in the developed steel was >1 wt.% to avoid carbide precipitation in the retained austenite during the bainitic transformation. The phase identification before and after various heat treatment conditions was carried out based on microstructural observations and x-ray diffraction. Hardness measurements and tensile tests were conducted to determine the mechanical properties of the investigated materials. In addition, following the tensile tests, the fracture surfaces of both types of steels were analyzed. Changing the bainitic transformation temperature generated distinct volume fractions of retained austenite and different values of mechanical strength properties. The mechanical properties of the examined steels were strongly influenced by the volume fractions and morphological features of the microstructural constituents. It is worth noting that the bainitic steel was characterized by a high ultimate tensile strength (1250 MPa) combined with a total elongation of 18% after austenitizing and continuous cooling. The chemical composition of the bainitic steel was designed to obtain the optimal microstructure and mechanical properties after hot deformation followed by natural cooling in still air. Extensive tests using isothermal transformation to bainite were conducted to understand the relationships between transformation temperature and the resulting microstructures, mechanical properties, and fracture characteristics. The isothermal transformation tests indicated that the optimal relationship between the sample strength and total elongation was obtained after bainitic treatment at 400 °C. However, it should be noted that the mechanical properties and total elongation of the bainitic steel after continuous cooling differed little from the condition after isothermal transformation at 400 °C.

Sign in / Sign up

Export Citation Format

Share Document