scholarly journals Visualization of the Oxygen Partial Pressure on the Gas-Diffusion-Layer Surface under the Single-Serpentine Flow Channel and the Ribs in a Polymer Electrolyte Membrane Fuel Cell during the Power Generation

2017 ◽  
Vol 68 (6) ◽  
pp. 338-343 ◽  
Author(s):  
Kazuhiro TAKANOHASHI ◽  
Makoto UCHIDA ◽  
Akihiro IIYAMA ◽  
Junji INUKAI
Keyword(s):  
Power Generation ◽  
Fuel Cell ◽  
Oxygen Partial Pressure ◽  
Partial Pressure ◽  
Polymer Electrolyte ◽  
Polymer Electrolyte Membrane ◽  
Gas Diffusion ◽  
Layer Surface ◽  
Electrolyte Membrane ◽  
Serpentine Flow Channel

Local Entropy Production Rates in a Polymer Electrolyte Membrane Fuel Cell

2017 ◽  
Vol 42 (1) ◽  
pp. 1-30 ◽  
Author(s):  
Marc Siemer ◽  
Tobias Marquardt ◽  
Gerardo Valadez Huerta ◽  
Stephan Kabelac
Keyword(s):  
Fuel Cell ◽  
Entropy Production ◽  
Polymer Electrolyte ◽  
Polymer Electrolyte Membrane ◽  
Gas Diffusion ◽  
Transport Processes ◽  
Local Entropy ◽  
Equilibrium Thermodynamics ◽  
Electrolyte Membrane ◽  
Non Equilibrium

AbstractA modeling study on a polymer electrolyte membrane fuel cell by means of non-equilibrium thermodynamics is presented. The developed model considers a one-dimensional cell in steady-state operation. The temperature, concentration and electric potential profiles are calculated for every domain of the cell. While the gas diffusion and the catalyst layers are calculated with established classical modeling approaches, the transport processes in the membrane are calculated with the phenomenological equations as dictated by the non-equilibrium thermodynamics. This approach is especially instructive for the membrane as the coupled transport mechanisms are dominant. The needed phenomenological coefficients are approximated on the base of conventional transport coefficients. Knowing the fluxes and their intrinsic corresponding forces, the local entropy production rate is calculated. Accordingly, the different loss mechanisms can be detected and quantified, which is important for cell and stack optimization.

Modeling the Effective Thermal Conductivity of an Anisotropic Gas Diffusion Layer in a Polymer Electrolyte Membrane Fuel Cell

2011 ◽  
Author(s):  
J. Yablecki ◽  
A. Bazylak
Keyword(s):  
Thermal Conductivity ◽  
Fuel Cell ◽  
Effective Thermal Conductivity ◽  
Polymer Electrolyte ◽  
Diffusion Layer ◽  
Compaction Pressure ◽  
Polymer Electrolyte Membrane ◽  
Gas Diffusion Layer ◽  
Gas Diffusion ◽  
Electrolyte Membrane

The anisotropic and heterogeneous effective thermal conductivity of the gas diffusion layer (GDL) of the polymer electrolyte membrane fuel cell was determined in the through-plane direction using an analytical thermal resistance model. The geometry of the GDL was reconstructed using porosity profiles obtained through microscale computed tomography imaging of four commercially available GDL materials. The effective thermal conductivity increases almost linearly with increasing bipolar plate compaction pressure. The effective thermal conductivity was also seen to increase with increasing GDL thickness as bulk porosity remained almost constant. The effect of the heterogeneous through-plane porosity distribution on the effective thermal conductivity is discussed. The outcomes of this work will provide insight into the effect of heterogeneity and anisotropy of the GDL on the thermal management required for improved PEMFC performance.

scholarly journals Impact of MPL on Temperature Distribution in Single Polymer Electrolyte Fuel Cell with Various Thicknesses of Polymer Electrolyte Membrane

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2499
Author(s):  
Akira Nishimura ◽  
Tatsuya Okado ◽  
Yuya Kojima ◽  
Masafumi Hirota ◽  
Eric Hu
Keyword(s):  
Power Generation ◽  
Fuel Cell ◽  
Temperature Distribution ◽  
Polymer Electrolyte ◽  
Polymer Electrolyte Membrane ◽  
Polymer Electrolyte Fuel Cell ◽  
Electrolyte Membrane ◽  
The Impact ◽  
Plane Temperature ◽  
Power Generation Performance

The impact of micro porous layer (MPL) with various thicknesses of polymer electrolyte membrane (PEM) on heat and mass transfer characteristics, as well as power generation performance of Polymer Electrolyte Fuel Cell (PEFC), is investigated. The in-plane temperature distribution on cathode separator back is also measured by thermocamera. It has been found that the power generation performance is improved by the addition of MPL, especially at higher current density condition irrespective of initial temperature of cell (Tini) and relative humidity condition. However, the improvement is not obvious when the thin PEM (Nafion NRE-211; thickness of 25 μm) is used. The increase in temperature from inlet to outlet without MPL is large compared to that with MPL when using thick PEM, while the difference between without MPL and with MPL is small when using thin PEM. It has been confirmed that the addition of MPL is effective for the improvement of power generation performance of single PEFC operated at higher temperatures than normal. However, the in-plane temperature distribution with MPL is not even.

Sign in / Sign up

Export Citation Format

Share Document