scholarly journals High Adhesion Plating Method on Fluorine-based Rubber with Atmospheric UV Treatment

2021 ◽  
Vol 72 (8) ◽  
pp. 450-452
Author(s):  
Katsuhiko TASHIRO ◽  
Yuka TSURUTA ◽  
Masaki MORI ◽  
Weishun ZENG ◽  
Yoshio HORIUCHI ◽  
...  
2013 ◽  
Vol 75 (3) ◽  
pp. 197-199
Author(s):  
Yuichi KURIHARA ◽  
MASUTAKA Furue

1997 ◽  
Vol 60 (6) ◽  
pp. 639-643 ◽  
Author(s):  
FUENG-LIN KUO ◽  
JOHN B. CAREY ◽  
STEVEN C. RICKE

The effects were investigated of 254-nm UV radiation on populations of Salmonella typhimurium, aerobes, and molds on the shells of eggs. In the first experiment, the CFU of attached S. typhimurium cells on unwashed clean shell eggs were determined after 0, 1, 3, 5, and 7 min of UV treatment (620 μW/cm2) on both ends of the egg. All UV treatments significantly reduced S. typhimurium CFU (P < .01). UVtreatment (620 μW/cm2) in 1-min alternating light and dark cycles for 5 min (three light and two dark) was compared to 0, 3, and 5 min of UV treatment. No significant differences in microbial populations were observed among light and dark cycles and the other UV treatments. In a subsequent experiment, the same UV treatments were utilized to evaluate photoreactivation. After UV exposure, eggs were exposed to 1 h of fluorescent light or I h of darkness or cultured immediately. S. typhimurium CFU were significantly (P < .01) reduced by the UV treatments. However, no significant differences between microbial populations exposed to UV treatment and UV radiation plus photoreactivation were detected. For studies of aerobic bacteria and molds, different UV treatment times (0, 15, and 30 min) at the intensity of 620 μW/cm2 and different intensities (620, 1350, and 1720 μW/cm2) for 15 min were evaluated. Mold CFU per egg were either 0 or 1 for all UV treatments and a 99% reduction of CFU of aerobic bacteria per egg were observed for all UV treatments. It appears from these studies that UV light can significantly reduce populations of S. typhimurium, aerobes, and molds on shell eggs.


2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Chao Ma ◽  
Jing Sun ◽  
Bo Li ◽  
Yang Feng ◽  
Yao Sun ◽  
...  

AbstractThe development of biomedical glues is an important, yet challenging task as seemingly mutually exclusive properties need to be combined in one material, i.e. strong adhesion and adaption to remodeling processes in healing tissue. Here, we report a biocompatible and biodegradable protein-based adhesive with high adhesion strengths. The maximum strength reaches 16.5 ± 2.2 MPa on hard substrates, which is comparable to that of commercial cyanoacrylate superglue and higher than other protein-based adhesives by at least one order of magnitude. Moreover, the strong adhesion on soft tissues qualifies the adhesive as biomedical glue outperforming some commercial products. Robust mechanical properties are realized without covalent bond formation during the adhesion process. A complex consisting of cationic supercharged polypeptides and anionic aromatic surfactants with lysine to surfactant molar ratio of 1:0.9 is driven by multiple supramolecular interactions enabling such strong adhesion. We demonstrate the glue’s robust performance in vitro and in vivo for cosmetic and hemostasis applications and accelerated wound healing by comparison to surgical wound closures.


Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1525
Author(s):  
Hao-ran Qi ◽  
Deng-xiong Shen ◽  
Yan-jiang Jia ◽  
Yuan-cheng An ◽  
Hao Wu ◽  
...  

High-temperature-resistant polymeric adhesives with high servicing temperatures and high adhesion strengths are highly desired in aerospace, aviation, microelectronic and other high-tech areas. The currently used high-temperature resistant polymeric adhesives, such as polyamic acid (PAA), are usually made from the high contents of solvents in the composition, which might cause adhesion failure due to the undesirable voids caused by the evaporation of the solvents. In the current work, electrospun preimidized polyimide (PI) nano-fibrous membranes (NFMs) were proposed to be used as solvent-free or solvent-less adhesives for stainless steel adhesion. In order to enhance the adhesion reliability of the PI NFMs, thermally crosslinkable phenylethynyl end-cappers were incorporated into the PIs derived from 3,3’,4,4’-oxydiphthalic anhydride (ODPA) and 3,3-bis[4-(4-aminophenoxy)phenyl]phthalide (BAPPT). The derived phenylethynyl-terminated PETI-10K and PETI-20K with the controlled molecular weights of 10,000 g mol−1 and 20,000 g mol−1, respectively, showed good solubility in polar aprotic solvents, such as N-methyl-2-pyrrolidinone (NMP) and N,N-dimethylacetamide (DMAc). The PI NFMs were successfully fabricated by electrospinning with the PETI/DMAc solutions. The ultrafine PETI NFMs showed the average fiber diameters (dav) of 627 nm for PETI-10K 695 nm for PETI-20K, respectively. The PETI NFMs showed good thermal resistance, which is reflected in the glass transition temperatures (Tgs) above 270 °C. The PETI NFMs exhibited excellent thermoplasticity at elevated temperatures. The stainless steel adherends were successfully adhered using the PETI NFMs as the adhesives. The PI NFMs provided good adhesion to the stainless steels with the single lap shear strengths (LSS) higher than 20.0 MPa either at room temperature (25 °C) or at an elevated temperature (200 °C).


Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 296
Author(s):  
Łukasz Szparaga ◽  
Przemysław Bartosik ◽  
Adam Gilewicz ◽  
Katarzyna Mydłowska ◽  
Jerzy Ratajski

One of the key components of the designing procedure of a structure of hard anti-wear coatings deposited via Physical Vapour Deposition (PVD) is the analysis of the stress and strain distributions in the substrate/coating systems, initiated during the deposition process and by external mechanical loads. Knowledge of residual stress development is crucial due to their significant influence on the mechanical and tribological properties of such layer systems. The main goal of the work is to find the optimal functionally graded material (FGM) coating’s structure, composed of three functional layers: (1) adhesive layer, providing high adhesion of the coating to the substrate, (2) gradient load support and crack deflection layer, improving hardness and enhancing fracture toughness, (3) wear-resistant top layer, reducing wear. In the optimisation procedure of the coating’s structure, seven decision criteria basing on the state of residual stresses and strains in the substrate/coating system were proposed. Using finite element simulations and postulated criteria, the thickness and composition gradients of the transition layer in FGM coating were determined. In order to verify the proposed optimisation procedure, Zr-C coatings with different spatial distribution of carbon concentration were produced by the Reactive Magnetron Sputtering PVD (RMS PVD) method and their anti-wear properties were assessed by scratch test and ball-on-disc tribological test.


2021 ◽  
Vol 146 ◽  
pp. 110253
Author(s):  
Zhenghao Li ◽  
Wenlong Xu ◽  
Xinhao Wang ◽  
Wenqing Jiang ◽  
Xiaolong Ma ◽  
...  

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3333
Author(s):  
Eduardo L. Silva ◽  
Sérgio Pratas ◽  
Miguel A. Neto ◽  
Cristina M. Fernandes ◽  
Daniel Figueiredo ◽  
...  

Cobalt-cemented carbide micro-end mills were coated with diamond grown by chemical vapor deposition (CVD), with the purpose of micro-machining cemented carbides. The diamond coatings were designed with a multilayer architecture, alternating between sub-microcrystalline and nanocrystalline diamond layers. The structure of the coatings was studied by transmission electron microscopy. High adhesion to the chemically pre-treated WC-7Co tool substrates was observed by Rockwell C indentation, with the diamond coatings withstanding a critical load of 1250 N. The coated tools were tested for micro-end-milling of WC-15Co under air-cooling conditions, being able to cut more than 6500 m over a period of 120 min, after which a flank wear of 47.8 μm was attained. The machining performance and wear behavior of the micro-cutters was studied by scanning electron microscopy and energy-dispersive X-ray spectroscopy. Crystallographic analysis through cross-sectional selected area electron diffraction patterns, along with characterization in dark-field and HRTEM modes, provided a possible correlation between interfacial stress relaxation and wear properties of the coatings. Overall, this work demonstrates that high adhesion of diamond coatings can be achieved by proper combination of chemical attack and coating architecture. By preventing catastrophic delamination, multilayer CVD diamond coatings are central towards the enhancement of the wear properties and mechanical robustness of carbide tools used for micro-machining of ultra-hard materials.


Sign in / Sign up

Export Citation Format

Share Document