Fluid-Assisted Injection Moulding Simulation: Virtual Prototyping for Complex Parts

Innovation in Engineering Computational Technology - Computational Science, Engineering & Technology Series ◽

10.4203/csets.15.14 ◽

2009 ◽

pp. 287-308 ◽

Cited By ~ 1

Author(s):

J. Sienz ◽

J.F.T. Pittman ◽

A. Polynkin

Keyword(s):

Injection Moulding ◽

Virtual Prototyping ◽

Complex Parts

Download Full-text

A virtual prototyping environment for a robust design of an injection moulding process

Computers & Chemical Engineering ◽

10.1016/j.compchemeng.2013.04.005 ◽

2013 ◽

Vol 54 ◽

pp. 159-169 ◽

Cited By ~ 6

Author(s):

Guido Berti ◽

Manuel Monti

Keyword(s):

Robust Design ◽

Injection Moulding ◽

Virtual Prototyping ◽

Moulding Process ◽

Injection Moulding Process

Download Full-text

Metal Injection Moulding of Titanium Medical Components

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.704.155 ◽

2016 ◽

Vol 704 ◽

pp. 155-160 ◽

Cited By ~ 2

Author(s):

Vera Friederici ◽

Thomas Hartwig

Keyword(s):

Surface Roughness ◽

Surface Quality ◽

Injection Moulding ◽

Optimal Parameters ◽

Serial Production ◽

Metal Injection Moulding ◽

Titanium Surfaces ◽

Cleaning Cycle ◽

Enhanced Surface ◽

Complex Parts

The metal injection moulding technique is already established for serial production of complex parts, mostly from various stainless steels. However, for other materials, especially for titanium parts there is still the need for superior purity and enhanced surface quality. Facing the challenge of obtaining suitable medical titanium MIM parts, advances have been made at Fraunhofer IFAM over the last few years.One strategy to overcome the high risk of carbon up-take was to adjust the sintering program. Very low Argon flow rates, 50 mbar pressure and two hours dwell time at 1350°C were found to be optimal parameters. A cleaning cycle prior to the actual sintering at 1450°C under hydrogen was also found to enhance the results.Another strategy involved the choice of binder components. Stearic acid, which is often used to improve wettability of binder to powder particle, and high polymer content affect the oxygen content of the titanium parts. Low amounts of both are beneficial for high purity parts.Other investigations were performed concerning the surface quality. It was found that the surface roughness of the mould has an effect on the surface roughness of the sintered parts. Although sintered titanium surfaces as such exhibit quite rough surfaces of about 2-3 µm (Ra value) the influence of the surface finish of the mould was detectable. Using very fine powders of only 15 µm mean particle size and a polished mould a very low surface roughness of less than 1.2 µm on the sintered part was obtainable.

Download Full-text

Geometrical algorithms for automated design of side actions in injection moulding of complex parts

Computer-Aided Design ◽

10.1016/j.cad.2007.05.014 ◽

2007 ◽

Vol 39 (10) ◽

pp. 882-897 ◽

Cited By ~ 21

Author(s):

Ashis Gopal Banerjee ◽

Satyandra K. Gupta

Keyword(s):

Injection Moulding ◽

Automated Design ◽

Complex Parts

Download Full-text

New injection moulding process for functional and complex parts

Metal Powder Report ◽

10.1016/s0026-0657(99)93586-5 ◽

1999 ◽

Vol 54 (7-8) ◽

pp. 37

Keyword(s):

Injection Moulding ◽

Moulding Process ◽

Injection Moulding Process ◽

Complex Parts

Download Full-text

Powder Injection Moulding (PIM) of Mesophase Carbon with Water-Based Binders

Advances in Science and Technology ◽

10.4028/www.scientific.net/ast.45.711 ◽

2006 ◽

Vol 45 ◽

pp. 711-713 ◽

Cited By ~ 2

Author(s):

Michael Gruhl ◽

B. Derfuss ◽

Christian Rottmair ◽

Andreas Volek ◽

Robert F. Singer

Keyword(s):

Mechanical Properties ◽

Injection Moulding ◽

Gelling Agent ◽

Powder Injection ◽

High Porosity ◽

Heating Rates ◽

Powder Injection Moulding ◽

Water Based ◽

High Heating ◽

Complex Parts

Since there are no net-shape techniques for complex parts made of mesophase carbon available yet, this work focuses on a powder injection moulding (PIM) approach. The single biggest problem to overcome here is the overlap of debindering and pyrolysis/sintering of mesocarbon when using conventional binders, causing high porosity and cracks. Water-based binders with agar as gelling agent can avoid this problem effectively by removing the binder in an optimized drying step. The subsequent sintering can then be carried out at high heating rates, leading to better densification and good mechanical properties. Furthermore, the dependency of the rheological properties of the water-based feedstock on its water content is investigated.

Download Full-text