scholarly journals Flexural Strength of Reinforced Concrete RAC Beams Exposed to 6-hour Fire – Part 2: Rich Mix

2019 ◽  
Vol 9 (1) ◽  
pp. 3814-3817 ◽  
Author(s):  
A. H. Buller ◽  
M. Oad ◽  
B. A. Memon
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Concrete Beams ◽  
Research Work ◽  
Testing Machine ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Load Testing ◽  
Group 2 ◽  
Comparison Of The Results

In this research work, experimental investigation on flexural strength of reinforced concrete beams exposed to fire for 6-hours at the temperature of 1000˚C is presented. The beams are made with 50% replacement of natural coarse aggregates with recyclable concrete aggregates. A total of 12 reinforced concrete beams using 1:1.5:3 mix (rich mix) and 0.54 water-cement ratio were cast. The beams were prepared in two groups. Group 1 beams were prepared with 50% recyclable aggregates, whereas group 2 beams were cast with all-natural aggregates (control specimens). All beams were exposed to fire at the above-mentioned temperature followed by testing in universal load testing machine under central point load. Comparison of the results reveals that proposed beams show comparable resistance even after exposed to 6-hours fire at 1000°C.

scholarly journals Effect of 12-hour fire on Flexural Behavior of Recyclable Aggregate Reinforced Concrete Beams

2019 ◽  
Vol 5 (7) ◽  
pp. 1533-1542 ◽  
Author(s):  
Abdul Hafeez Buller ◽  
Bashir Ahmed Memon ◽  
Mahboob Oad
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Research Work ◽  
Testing Machine ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Flexural Behavior ◽  
Partial Replacement ◽  
Load Testing ◽  
Coarse Aggregates

Fire being one of the hazards causes external and internal adverse effects on concrete. On the other hand, demolishing waste causes numerous environmental issues due to lack of proper disposal management. Therefore, this research work presents experimental evaluation of effect of 12-hur fire on flexural behavior of reinforced concrete beams made with partial replacement of natural coarse aggregates with coarse aggregates from demolished concrete. The model beams are prepared using both normal and rich mix. Natural coarse aggregates are replaced in 50% dosage. Also, the beams without recyclable aggregates are prepared to check the results of proposed beams. After 28-day curing all the beams are exposed to fire for 12-hour at 1000°C in purpose made oven, followed by testing in universal load testing machine under central point load. During the testing deflection, load, and cracks are monitored. Analysis of flexural behavior and cracking reveals that after 12-hour fire residual strength of the beams is 52%. This shows loss of the strength of reinforced concrete beams thus requires appropriate retrofitting decision before putting again the structure in service after fire. Observation of cracks shows that most of the beams failed in shear with minor flexural cracks. In comparison to the results of control specimen the proposed beams show good fire resistance. The outcome of the research will prove landmark for future scholars and help the industry personals in understanding the behavior of the material in fire.

scholarly journals 24-hour Fire Produced Effect on Reinforced Recycled Aggregates Concrete Beams

2019 ◽  
Vol 9 (3) ◽  
pp. 4213-4217 ◽  
Author(s):  
A. H. Buller ◽  
M. Oad ◽  
B. A. Memon ◽  
S. Sohu
Keyword(s):  
Flexural Strength ◽  
Concrete Beams ◽  
Testing Machine ◽  
Maximum Load ◽  
Reinforced Concrete Beams ◽  
Recycled Aggregates ◽  
Equal Proportion ◽  
Load Testing ◽  
Coarse Aggregates ◽  
Natural Aggregates

In this article, the effect of prolonged fire (24-hour duration) on reinforced concrete beams made with recycled aggregates from demolished concrete was experimentally investigated. Demolished concrete was used recycled coarse aggregates in equal proportion with natural coarse aggregates. Normal and rich mix concrete with water-cement ratio equal to 0.54 were used. As a control specimen, beams with all-natural aggregates were also cast to compare with the results of the proposed beams. All beams were cured for 28 days and exposed to fire at 1000°C in an oven for 24 hours. After the elapse of this fire period, the beams were allowed to air cool, followed by testing till failure in a universal load testing machine. Comparison of the test results shows that rich mix concrete beams more reduction in flexural strength, more increase in maximum load carrying capacity and deflection than normal mix beams. The maximum reduction in flexural strength was 32.41% for beams cast with 50% RCA and rich mix. Although the fire duration used in this study is rare, yet the outcome provides guidelines for taking proper decisions for retrofitting/strengthening of the fire affected structure before putting it back in service.

Application of acoustic emission monitoring for assessment of bond performance of corroded reinforced concrete beams

2016 ◽  
Vol 16 (6) ◽  
pp. 732-744 ◽  
Author(s):  
Ahmed A Abouhussien ◽  
Assem AA Hassan
Keyword(s):  
Acoustic Emission ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Signal Strength ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Bond Failure ◽  
Acoustic Emission Monitoring ◽  
Bond Performance ◽  
Emission Monitoring

This article presents the results of an experimental investigation on the application of acoustic emission monitoring for the evaluation of bond behaviour of deteriorated reinforced concrete beams. Five reinforced concrete beam–anchorage specimens designed to undergo bond failure were exposed to corrosion at one of the anchorage zones by accelerated corrosion. Two additional beams without exposure to corrosion were included as reference specimens. The corroded beams were subjected to four variable periods of corrosion, leading to four levels of steel mass loss (5%, 10%, 20% and 30%). After these corrosion periods, all seven beams were tested to assess their bond performance using a four-point load setup. The beams were continuously monitored by attached acoustic emission sensors throughout the four-point load test until bond failure. The analysis of acquired acoustic emission signals from bond testing was performed to detect early stages of bond damage. Further analysis was executed on signal strength of acoustic emission signals, which used cumulative signal strength, historic index ( H( t)) and severity ( Sr) to characterize the bond degradation in all beams. This analysis allowed early identification of three stages of damage, namely, first crack, initial slip and anchorage cracking, before their visual observation, irrespective of corrosion level or sensor location. Higher corrosion levels yielded significant reduction in both bond strength and corresponding acoustic emission parameters. The results of acoustic emission parameters ( H( t) and Sr) enabled the development of a damage classification chart to identify different stages of bond deterioration.

scholarly journals Effect of Plastering Layer on Corrosion Resistances of Reinforced Concrete Beams

2019 ◽  
Vol 9 (1) ◽  
pp. 1390-1393
Keyword(s):  
Corrosion Resistance ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Experimental Program ◽  
Structural Elements ◽  
Accelerated Corrosion ◽  
Total Mass Loss ◽  
Load Arrangement

Reinforced concrete structures are subjected to deterioration due to many factors such as corrosion of reinforcing steel. Ultimate strengths of structural elements can be greatly affected by these deteriorating factors. There are numerous methods and techniques used to protect these structural elements. The mortar layer (Plastering) is considered the first defense line against all the deteriorating factors. The main goal of this research is to investigate to what extent the plastering layer can protect reinforced concrete beams against corrosion. The aim of the experimental program is to study the effect of plastering layer on corrosion resistance of reinforced concrete beams. Four reinforced concrete beams (1002001100 mms) and four Lollypop specimens (cylinders 100200 mms) were tested and described as follows: • A beam and a lollypop specimen without any plastering layer (control). • A beam and a lollypop specimen with traditional plastering layer (cement + sand + water). • A beam and a lollypop specimen with modified plastering (traditional plastering + waterproof admixtures). • A beam and a lollypop specimen with painted and modified plastering layer (traditional plastering + waterproof admixtures + external waterproof paint). These eight specimens were subjected to corrosion using accelerated corrosion technique, after that the four beams were tested in flexure under three point load arrangement while the four lollypops were used to calculate the total mass loss due to accelerated corrosion. The test results were used to figure out the effect of plastering layer on corrosion resistance of RC beams.

Prediction of residual flexural strength of corroded reinforced concrete beams

2017 ◽  
Vol 64 (1) ◽  
pp. 69-74 ◽  
Author(s):  
Shamsad Ahmad
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Current Density ◽  
Empirical Model ◽  
Corrosion Current Density ◽  
Concrete Beams ◽  
Corrosion Current ◽  
Reinforced Concrete Beams ◽  
Content Type ◽  
Rebar Corrosion

Purpose This study aims to make an effort to develop a model to predict the residual flexural strength of reinforced concrete beams subjected to reinforcement corrosion. Design/methodology/approach For generating the required data to develop the model, a set of experimental variables was considered that included corrosion current density, corrosion duration, rebar diameter and thickness of concrete cover. A total of 28 sets of reinforced concrete beams of size 150 × 150 × 1,100 mm were cast, of which 4 sets of un-corroded beams were tested in four-point bend test as control beams and the remaining 24 sets of beams were subjected to accelerated rebar corrosion inducing different levels of corrosion current densities for different durations. Corroded beams were also tested in flexure, and test results of un-corroded and corroded beams were utilized to obtain an empirical model for estimating the residual flexural strength of beams for given corrosion current density, corrosion duration and diameter of the rebars. Findings Comparison of the residual flexural strengths measured experimentally for a set of corroded beams, reported in literature, with that predicted using the model proposed in this study indicates that the proposed model has a reasonably good accuracy. Originality/value The empirical model obtained under this work can be used as a simple tool to predict residual flexural strength of corroded beams using the input data that include rebar corrosion rate, corrosion duration after initiation and diameter of rebars.

Flexural strength of corroded reinforced concrete beams

2010 ◽  
Vol 62 (6) ◽  
pp. 405-414 ◽  
Author(s):  
A.K. Azad ◽  
S. Ahmad ◽  
B.H.A. Al-Gohi
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Concrete Beams ◽  
Reinforced Concrete Beams
Sign in / Sign up

Export Citation Format

Share Document