scholarly journals Effect of Plastering Layer on Corrosion Resistances of Reinforced Concrete Beams

2019 ◽  
Vol 9 (1) ◽  
pp. 1390-1393
Keyword(s):  
Corrosion Resistance ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Experimental Program ◽  
Structural Elements ◽  
Accelerated Corrosion ◽  
Total Mass Loss ◽  
Load Arrangement

Reinforced concrete structures are subjected to deterioration due to many factors such as corrosion of reinforcing steel. Ultimate strengths of structural elements can be greatly affected by these deteriorating factors. There are numerous methods and techniques used to protect these structural elements. The mortar layer (Plastering) is considered the first defense line against all the deteriorating factors. The main goal of this research is to investigate to what extent the plastering layer can protect reinforced concrete beams against corrosion. The aim of the experimental program is to study the effect of plastering layer on corrosion resistance of reinforced concrete beams. Four reinforced concrete beams (1002001100 mms) and four Lollypop specimens (cylinders 100200 mms) were tested and described as follows: • A beam and a lollypop specimen without any plastering layer (control). • A beam and a lollypop specimen with traditional plastering layer (cement + sand + water). • A beam and a lollypop specimen with modified plastering (traditional plastering + waterproof admixtures). • A beam and a lollypop specimen with painted and modified plastering layer (traditional plastering + waterproof admixtures + external waterproof paint). These eight specimens were subjected to corrosion using accelerated corrosion technique, after that the four beams were tested in flexure under three point load arrangement while the four lollypops were used to calculate the total mass loss due to accelerated corrosion. The test results were used to figure out the effect of plastering layer on corrosion resistance of RC beams.

scholarly journals Experimental study of RC beams strengthened for bending by reinforced grout layer and connectors

2018 ◽  
Vol 11 (4) ◽  
pp. 810-833
Author(s):  
J. H. CANAVAL ◽  
T. J. DA SILVA ◽  
A. C. SANTOS
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Concrete Beams ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Bending Test ◽  
Experimental Program ◽  
Rc Beams

Abstract This work is based on an experimental investigation of reinforced concrete beams strengthened to flexure for wrapping applying a type of metallic connector in the bond substrate/groute. The experimental program consisted of 5 beams used for reference (without strengthening), 5 beams reinforced with surface brushed texture substrate and 5 beams with metal connectors bonded to the substrate. The beams were submitted to four-point load bending test. Initially with a partial loading, executed the strengthening and were finally tested until the break. The strengthening was made up by the increase by graute, on the sides and bottom of the beam and reinforcing. The applied force, the displacement, deformations in steel and in concrete were measured. The reference beams failure by flexing with the calculated charges. The bending strengthening proved efficient, increasing the bearing capacity in 44% and the failure was by shear in the stretch without strengthening. Beams with connectors the increase was higher.

Application of acoustic emission monitoring for assessment of bond performance of corroded reinforced concrete beams

2016 ◽  
Vol 16 (6) ◽  
pp. 732-744 ◽  
Author(s):  
Ahmed A Abouhussien ◽  
Assem AA Hassan
Keyword(s):  
Acoustic Emission ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Signal Strength ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Bond Failure ◽  
Acoustic Emission Monitoring ◽  
Bond Performance ◽  
Emission Monitoring

This article presents the results of an experimental investigation on the application of acoustic emission monitoring for the evaluation of bond behaviour of deteriorated reinforced concrete beams. Five reinforced concrete beam–anchorage specimens designed to undergo bond failure were exposed to corrosion at one of the anchorage zones by accelerated corrosion. Two additional beams without exposure to corrosion were included as reference specimens. The corroded beams were subjected to four variable periods of corrosion, leading to four levels of steel mass loss (5%, 10%, 20% and 30%). After these corrosion periods, all seven beams were tested to assess their bond performance using a four-point load setup. The beams were continuously monitored by attached acoustic emission sensors throughout the four-point load test until bond failure. The analysis of acquired acoustic emission signals from bond testing was performed to detect early stages of bond damage. Further analysis was executed on signal strength of acoustic emission signals, which used cumulative signal strength, historic index ( H( t)) and severity ( Sr) to characterize the bond degradation in all beams. This analysis allowed early identification of three stages of damage, namely, first crack, initial slip and anchorage cracking, before their visual observation, irrespective of corrosion level or sensor location. Higher corrosion levels yielded significant reduction in both bond strength and corresponding acoustic emission parameters. The results of acoustic emission parameters ( H( t) and Sr) enabled the development of a damage classification chart to identify different stages of bond deterioration.

Laboratory Fast Corrosion Test of Plain Steel Bars in Concrete Beams

2012 ◽  
Vol 535-537 ◽  
pp. 1803-1806
Author(s):  
Shun Bo Zhao ◽  
Peng Bing Hou ◽  
Fu Lai Qu
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Numerical Models ◽  
Concrete Strength ◽  
Reinforced Concrete Beams ◽  
Uniform Corrosion ◽  
Pure Bending ◽  
Accelerated Corrosion ◽  
Steel Bars ◽  
Bending Length

An experimental study was carried out to examine the non-uniform corrosion of plain steel bars in reinforced concrete beams partially placed in 5% sodium chloride solution under conditions of accelerated corrosion. 4 reinforced concrete beams with different concrete strength were made. The crack distributions of the beams due to pre-loads and expansion of corrosion product, and the sectional corrosion characteristics of plain steel bars are described in detail. The sectional area loss relating to mass loss and change along pure bending length of the beams are discussed. These can be used as the basis of test for further studies to build the numerical models of serviceability of corroded reinforced concrete beams.

scholarly journals Reliability of beams designed in accordance with Brazilian codes

2014 ◽  
Vol 7 (5) ◽  
pp. 723-746 ◽  
Author(s):  
D. M. Santos ◽  
F. R. Stucchi ◽  
A. T. Beck
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Composite Beams ◽  
Reinforced Concrete Beams ◽  
Steel Beams ◽  
Structural Elements ◽  
Pure Bending ◽  
Design Standards ◽  
Limit Values ◽  
Relative Safety

This paper presents an investigation on the safety of structural elements submitted to pure bending, produced in reinforced concrete, in steel and steel-concrete composites, and designed according to Brazilian codes NBR8681:2003, NBR6118:2007 and NBR8800:2008. The study allows a comparison of the relative safety of beams produced with these materials and designed using these codes. Comparative studies between the performances of different materials are difficult to find in the published literature. The present study shows that reliability indexes for reinforced concrete beams are satisfactory; however, results for steel beams are below limit values established in international design standards. Reliability indexes found herein for steel-concrete composite beams are intermediate to concrete and steel beams.

Shear strength of disturbed regions with corroded stirrups in reinforced concrete beams

2010 ◽  
Vol 37 (8) ◽  
pp. 1045-1056 ◽  
Author(s):  
Christopher Suffern ◽  
Ahmed El-Sayed ◽  
Khaled Soudki
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Corrosion Damage ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Accelerated Corrosion ◽  
Damage Level ◽  
Three Point Bending ◽  
Shear Span

This paper reports experimental data on the structural performance of disturbed regions in reinforced concrete beams with corrosion damage to the embedded steel stirrups. A total of 15 reinforced concrete beams were constructed and tested. The test beams were 350 mm deep, 125 mm wide, and 1850 mm long. The beams were tested in three-point bending under a simply supported span of 1500 mm. Nine beams had the embedded stirrups subjected to accelerated corrosion. The test variables were the corrosion damage level and the shear span-to-depth ratio. The test results indicated that the corroded beams exhibited reduced shear strength in comparison to the uncorroded control specimens. The shear strength reduction was up to 53%. Furthermore, the reduction in shear strength due to the corrosion was found to be greater at smaller shear span-to-depth ratios.

scholarly journals Experimental analysis of steel fiber reinforced concrete beams in shear

2022 ◽  
Vol 15 (3) ◽  
Author(s):  
Aaron Kadima Lukanu Lwa Nzambi ◽  
Dênio Ramam Carvalho de Oliveira ◽  
Marcus Vinicius dos Santos Monteiro ◽  
Luiz Felipe Albuquerque da Silva
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Experimental Program ◽  
Longitudinal Reinforcement ◽  
Fiber Addition

Abstract Some normative recommendations are conservative in relation to the shear strength of reinforced concrete beams, not directly considering the longitudinal reinforcement rate. An experimental program containing 8 beams of (100 x 250) mm2 and a length of 1,200 mm was carried out. The concrete compression strength was 20 MPa with and without 1.00% of steel fiber addition, without stirrups and varying the longitudinal reinforcement ratio. Comparisons between experimental failure loads and main design codes estimates were assessed. The results showed that the increase of the longitudinal reinforcement ratio from 0.87% to 2.14% in beams without steel fiber led to an improvement of 59% in shear strength caused by the dowel effect, while the corresponding improvement was of only 22% in fibered concrete beams. A maximum gain of 109% in shear strength was observed with the addition of 1% of steel fibers comparing beams with the same longitudinal reinforcement ratio (1.2%). A significant amount of shear strength was provided by the inclusion of the steel fibers and allowed controlling the propagation of cracks by the effect of stress transfer bridges, transforming the brittle shear mechanism into a ductile flexural one. From this, it is clear the shear benefit of the steel fiber addition when associated to the longitudinal reinforcement and optimal values for this relationship would improve results.

scholarly journals Flexural performance of reinforced concrete beams strengthened with fibre reinforced geopolymer concrete under accelerated corrosion

Structures ◽  
2019 ◽  
Vol 19 ◽  
pp. 394-410 ◽  
Author(s):  
Mohammed Haloob Al-Majidi ◽  
Andreas P. Lampropoulos ◽  
Andrew B. Cundy ◽  
Ourania T. Tsioulou ◽  
Salam Alrekabi
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Geopolymer Concrete ◽  
Accelerated Corrosion ◽  
Flexural Performance

scholarly journals Effect of Using Different Aspect Ratio of Longitudinal Steel Plates in Reinforced Concrete Beams

2021 ◽  
Vol 318 ◽  
pp. 03016
Author(s):  
Khalid I. Qaddoory ◽  
Ahmed A. Mansor ◽  
Ahlam S. Mohammed ◽  
Bilal J. Noman
Keyword(s):  
Reinforced Concrete ◽  
Steel Plate ◽  
Concrete Beams ◽  
Reference Model ◽  
Plate Thickness ◽  
Reference Beam ◽  
Point Load ◽  
Reinforced Concrete Beams ◽  
Steel Plates ◽  
Cross Sectional

In the past few years, new techniques have emerged using steel plates instead of traditional reinforcement in the reinforced concrete beams. This study deals with using a new method for reinforced concrete beams using steel plates instead of traditional steel bars with different thicknesses of (4, 5, and 6 mm) placed vertically inside the lower part of the beam. Four reinforced concrete beams were cast and tested under a two-point load. All beams had the same cross-sectional area of reinforcement and dimensions of 2100 mm in length, 350 mm in height, and 250 in width. The results showed that as the thickness of the steel plate increases, the samples would have greater resistance until more deflection is produced. In addition, there is a reduction in the crack load, ultimate load, and yield load when replacing reinforcing bars with steel plates. In which, a reduction in crack load by about 11.1, 15.5, and 22.2% plate thicknesses of 4,5,6 mm respectively, compared to reference beam that had a deformed steel bar (Dia. 16 mm). In addition, a reduction in yielding load was observed about 42, 53, and 60% for steel plate thickness of 4, 5, and 6 mm respectively, compared to the reference model. Finally, the cracks for all the steel plate specimens compared to reference specimens were wider and smaller.

Sign in / Sign up

Export Citation Format

Share Document