scholarly journals Comparison of Shear Bond Strength and Microleakage of Various Bulk-fill Bioactive Dentin substitutes: An in vitro Study

2016 ◽  
Vol 17 (12) ◽  
pp. 997-1002 ◽  
Author(s):  
Fahad I Alkhudhairy ◽  
Zeeshan H Ahmad
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Physical And Mechanical Properties ◽  
Pairwise Comparison ◽  
In Vitro Study ◽  
Composite Resins ◽  
Intergroup Comparison ◽  
Significant Difference ◽  
Tukey Honestly Significant Difference

ABSTRACT Introduction Various bulk-fill materials depending on their composition, viscosity, and flow ability have different physical and mechanical properties. The aim of this in vitro study was to determine and compare the shear bond strength and microleakage properties of activa restorative with other bulk-fill restorative materials surefil (SDR), Biodentine, ever X posterior. Materials and methods Forty permanent premolars were selected for shear bond strength, and 20 permanent premolars were selected with class II cavities on mesial and distal side for microleakage. Universal testing device was used to assess the shear bond strength. Microleakage was checked using dye penetration method under a stereomicroscope. Mean and standard deviation values were calculated from the recorded values. Intergroup comparison was done by one-way analysis of variance (ANOVA) followed by pairwise comparison using Tukey honestly significant difference (HSD) post hoc test. Results The mean shear bond strength was highest for SDR surefil followed by Ever X posterior, Bioactive restorative, and Biodentine respectively. In this study, SDR (surefil) showed better shear bond strength and better microleakage properties compared with the other test materials (F = 186.7157, p < 0.05). Conclusion The result of this study showed that flowable and fiber-reinforced composites have better shear bond strength and microleakage properties. Clinical significance Flowable bulk-fill composite resins can be used as dentin substitutes because of its superior properties. How to cite this article Alkhudhairy FI, Ahmad ZH. Comparison of Shear Bond Strength and Microleakage of Various Bulk-fill Bioactive Dentin substitutes: An in vitro study. J Contemp Dent Pract 2016;17(12):997-1002.

scholarly journals Comparison of Shear Bond Strength of MIM Technology Brackets with Conventional and Rail-Shaped Mesh Bases: An In Vitro Study

2019 ◽  
Vol 13 (1) ◽  
pp. 255-260
Author(s):  
Francisco Molina ◽  
Karina Maria Salvatore Freitas ◽  
Maria Cristina Rockenbach Binz Ordóñez ◽  
Emerson Flamarion Cruz ◽  
Rafael Pinelli Henriques ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Dental Enamel ◽  
In Vitro Study ◽  
Metal Injection Molding ◽  
Test Machine ◽  
Intergroup Comparison ◽  
Significant Difference ◽  
Mim Technology

Objective: The objective of this study was to evaluate in vitro the shear bond strength of two types of MIM (Metal Injection Molding) technology brackets, one with conventional mesh base and the other with rail-shaped mesh base. Materials and Methods: Forty human premolars received the bonding of 2 types of brackets: Group 1- 20 Synergy metal brackets (Rocky Mountain) with conventional mesh base and Group 2-20 H4 brackets (OrthoClassic) with rail-shaped mesh base. Both brackets were bonded with Resilience photopolymerizable resin (OrthoTechnology). The specimens were coupled to a Tinius Olsen universal test machine where the shear test was performed using a chisel. In addition, the amount of remaining resin in tooth crown with the ImageJ program was evaluated and the Adhesive Remnant Index (ARI). Intergroup comparison was performed by the independent t test and Chi-square test. Results: There was no statistically significant difference between the groups for any of the measures evaluated indicating that the mesh type of the brackets’ base with MIM technology did not influence the shear bond strength of the brackets (shear bond strength, p=0.191; maximum load registered, p=0.244). There was also no difference between the percentage (p=0.602) and area of remaining resin in the teeth (p=0.805) and IRA (p=0.625) between the Synergy and H4 groups. Conclusion: Shear bond strength was similar in the two types of brackets with MIM technology evaluated. In addition, the remaining resin in the dental enamel of two types of brackets were also similar.

scholarly journals Effect of Adhesion Booster on Fluoride-releasing Composite: An in vitro Study

2018 ◽  
Vol 7 (2) ◽  
pp. 28-31
Author(s):  
Varunjeet Chaudhary ◽  
Sanad Singh Solanki ◽  
Varsha Yadav ◽  
Seema Lahoti
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Composite Resins ◽  
Control Group ◽  
Bonding Agents ◽  
Significant Difference ◽  
Group 2

Objective: To evaluate the shear bond strength of stainless steel brackets bonded with fluoride-releasing composite resins, comparing effect of adhesion booster and conventional primer.Materials & Method: Sixty extracted premolars were subjected to bracket bonding with fluoride-releasing composite resin; which were bonded by randomly divided into two groups of bonding agents: Group 1- conventional primer as control group, Group 2- adhesion booster. After bonding, the samples were thermocycled (500 cycles) at 5ºC and 55ºC temperatures. After 48 hours they were subjected to shear bond strength testing in occluso-gingival direction, using an MTS 810 Universal Testing Machine with load speed of 0.5 mm/min.Result: Mean shear bond strength was significantly more in samples bonded with adhesion booster (14.792±3.805 Mpa) as compared to conventional primers (11.327±4.047 Mpa). There was statistically significant difference in shear bond strength between the groups (p=0.001).Conclusion: The use of the adhesion booster significantly increased the bond strength of bracket bonded with fluoride-releasing composite.

scholarly journals Shear Bond Strength of Three Composite Resins to Fluorosed and Sound Dentine: In Vitro Study

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Sabra Jaâfoura ◽  
Amira Kikly ◽  
Saida Sahtout ◽  
Mounir Trabelsi ◽  
Dorra Kammoun
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Adhesive System ◽  
Composite Resins ◽  
Vitro Study ◽  
Adhesion Forces ◽  
Average Shear ◽  
One Way Anova

Introduction. This in vitro study compared the shear strength of three composite resin systems to fluorosed and normal dentin. Methods. Silorane FiltekTM P90, FiltekTMZ250 XT in combination with the adhesive system AdperTM Single bond 2, and Amelogen® Plus in association with Peak Universal Bond® were tested. Fifteen normal and 15 fluorosed dentine disks were prepared per material. The shear bond strength test was performed using a universal machine. Results. One-way ANOVA revealed significant differences in bond strength between the tested composite resins. All tested materials had significantly different adhesion at the fluorosed and the nonfluorosed interface. FiltekTM Z250 XT and Silorane had lower adhesion values to fluorosed than to normal dentin. In contrast, Amelogen® Plus presented a better average resistance at the fluorosed interface. Conclusion. Amelogen® Plus presented a better average shear bond strength on the fluorosed dentine. FiltekTMZ250 XT showed the best adhesion forces and shear bond strength with sound dentine. Further studies are needed to better understand the sealing of these systems.

scholarly journals INFLUÊNCIA DA MODIFICAÇÃO DA BASE DE COLAGEM E DA CONTAMINAÇÃO SALIVAR NA RESISTÊNCIA DE UNIÃO DE TUBOS ORTODÔNTICOS COLADOS AO ESMALTE HUMANO

2021 ◽  
Vol 58 (1) ◽  
pp. eUJ3657
Author(s):  
Germano Brandão ◽  
◽  
Liliana Ávila Maltagliati ◽  
Ana Carla Raphaelli Nahás-Scocate ◽  
Murilo Matias ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Statistical Significance ◽  
Testing Machine ◽  
In Vitro Study ◽  
Metal Mesh ◽  
Human Teeth ◽  
Significance Level ◽  
Significant Difference

The objective of this in vitro study was to assess and compare the shear bond strength of conventional and modified orthodontic tubes bonded to the surface of dry and saliva-contaminated enamel. The sample consisted of 40 human teeth, which were randomly divided into four groups according to attachment base and presence or absence of saliva contamination as follows: Group CB, conventional orthodontic tubes without salivary contamination; Group CB-S, conventional orthodontic tubes with salivary contamination; Groups BM, orthodontic tubes modified by welding a metal mesh to their base without salivary contamination; and Group BM-S, modified orthodontic tubes with salivary contamination. Shear bond strength test was performed in a universal testing machine and analysis of the adhesive remnant index (ARI) by optical microscopy. Two-way ANOVA was used, followed by Tukey’s test at a statistical significance level of 5%. The ARI results were analysed descriptively. There was statistically significant difference between the groups regarding the shear bond strength values, with conventional tubes presenting significantly higher values (P < 0.05). In addition, the presence of salivary contamination interfered negatively with the behaviour of conventional tubes only (P < 0.05). Shear bond strength was not improved by increasing the area of the orthodontic tubes. Moreover, salivary contamination influenced negatively the SBS values, but only when conventional tubes were used.

scholarly journals A Comparative Evaluation of Three Commercially Available Dentin Desensitizers on the Shear Bond Strength of Composite Resins: An in vitro Study

2015 ◽  
Vol 5 (2) ◽  
pp. 65-68
Author(s):  
Shruti Patil ◽  
Prajna Shetty
Keyword(s):  
Bond Strength ◽  
Comparative Evaluation ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Composite Resins ◽  
Group 4 ◽  
Group 3 ◽  
Group 2 ◽  
Group 1

ABSTRACT Background The dentin desensitizers available for in-office application for prevention and/or treatment of post restorative dentinal hypersensitivity, act by blocking the open dentinal tubules. In doing so, they may influence the bond strength of the restorative resins. Thus, the aim of the study was to evaluate the effect of desensitizers on the shear bond strength of dentin adhesives and to check the extent of dentinal tubule occlusion caused by these desensitizers. Materials and Methods Sixty-four premolars were randomly divided into four groups of sixteen each. The middle depth dentin was exposed by on the buccal surface and was etched using 37% phosphoric acid and rinsed. They were assigned to, Group 1: Gluma desensitizer, Group 2: Vivasens desensitizer, Group 3: Gluma Comfort Bond and desensitizer, and Group 4: Adper Single Bond 2. Composite resin post of 2 mm in height and width were built on these specimens. The samples were then mounted in acrylic resin blocks. Universal testing machine was used to test the shear bond strength. The data were analyzed using one-way analysis of variance (ANOVA) and post hoc Tukey's test. Results The mean values of the shear bond strength were for: Group 1—18.61 ± 1.03 MPa, Group 2—17.53 ± 1.36 MPa, Group 3—22.63 ± 1.61 MPa and Group 4—23.12 ± 1.02 MPa. There was a statistically significant difference (p < 0.05) among the groups. Conclusion The use of dentin desensitizers’ influences bond strength between the tooth and the adhesive. Among the various agents, the single bottle system containing Gluma comfort bond and desensitizer had the best adhesion among the desensitizer groups. How to cite this article Patil S, Naik B, Shetty P. A Comparative Evaluation of Three Commercially Available Dentin Desensitizers on the Shear Bond Strength of Composite Resins: An in vitro Study. J Contemp Dent 2015;5(2):65-68.

scholarly journals Shear bond strength of ceramic laminate veneers to finishing surfaces with different percentages of preserved enamel under a digital guided method

2022 ◽  
Vol 22 (1) ◽  
Author(s):  
Jiakang Zhu ◽  
Jing Gao ◽  
Luming Jia ◽  
Xin Tan ◽  
Chenyang Xie ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Three Dimensional ◽  
In Vitro Study ◽  
Significant Difference ◽  
Dimensional Models ◽  
Three Dimensional Models ◽  
Laminate Veneers ◽  
Bonding Surface

Abstract Background The purpose of this in vitro study was to evaluate the effect of the percentages of preserved enamel on ceramic laminate veneers’ (CLVs) shear bond strength (SBS). Methods Seventy extracted human maxillary central incisors were scanned and reconstructed into three-dimensional models. The extracted teeth were then embedded and randomly divided into seven groups (n = 10 per group). Based on digital analyses of the three-dimensional models, guided tooth preparation and bonding procedures were performed individually to form seven different percentages (100%, 80%, 60% 50%, 40%, 20% and 0%) of remaining enamel thickness on the bonding surface. Finally, the SBS test was performed, and the data were statistically analysed by one-way ANOVA with LSD post hoc test (α = 0.05). Results The complete enamel surface exhibited the highest SBS (19.93 ± 4.55 MPa), followed by 80% enamel (19.03 ± 3.66 MPa), 60% enamel (18.44 ± 3.65 MPa), 50% enamel (18.18 ± 3.41 MPa), 40% enamel (17.83 ± 3.01 MPa) and 20% enamel (11.32 ± 3.42 MPa) group. The lowest SBS (9.63 ± 3.46 MPa) was detected in 0% enamel group. No significant difference was observed among the 40–100% enamel groups, while the 20% or 0% enamel group demonstrated a significantly lower mean SBS than the 40% enamel group (p < 0.05). Conclusion The SBS value of CLVs bonded to 100% enamel on the finishing surfaces (nearly 20 MPa) was twice that which bonded to 0% enamel (nearly 10 MPa). Bonding to 100% enamel is the most reliable treatment. When dentin exposure is inevitable, enamel should be preserved as much as possible to maintain good bonding. In addition, 40% of preserved enamel on the bonding surface was the minimal acceptable value to fulfil the requirements of good bonding strength.

scholarly journals Effect of different surface treatments on shear bond strength of ceramic brackets to old composite

2020 ◽  
Vol 24 (1) ◽  
Author(s):  
Homa Farhadifard ◽  
Loghman Rezaei-Soufi ◽  
Maryam Farhadian ◽  
Parisa Shokouhi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Surface Treatments ◽  
Composite Resins ◽  
Control Group ◽  
Composite Restorations ◽  
Ceramic Brackets ◽  
Aged Composite

Abstract Background At present, the demand for orthodontic treatment is on the rise. On the other hand, evidence shows that the bond strength of composite resins to old composite restorations is often unreliable. Therefore, the aim of this in vitro study was to assess the effect of different surface treatments on shear bond strength (SBS) of ceramic brackets to old composite restorations. Methods In this in vitro experimental study, 60 nano-hybrid composite discs were fabricated. For aging, the discs were incubated in deionized water at 37 °C for 1 month. Next, they underwent 4 different surface treatments namely acid etching with 37% phosphoric acid, sandblasting, grinding, and Er,Cr:YSGG laser irradiation. Ceramic brackets were then bonded to the discs and underwent SBS testing. Results The maximum mean SBS value was obtained in the grinding group (9.16 ± 2.49 MPa), followed by the sandblasting (8.13 ± 2.58 MPa) and laser (6.57 ± 1.45 MPa) groups. The minimum mean SBS value was noted in the control group (5.07 ± 2.14 MPa). Conclusion All groups except for the control group showed clinically acceptable SBS. Therefore, grinding, sandblasting, and Er,Cr:YSGG laser are suggested as effective surface treatments for bonding of ceramic orthodontic brackets to aged composite.

Effect of Bonding Agent on Retention of Different Sealants: An in Vitro Study

2021 ◽  
Vol 45 (3) ◽  
pp. 177-185
Author(s):  
Moaz H Attar ◽  
Medhat A Abdallah ◽  
Hussein A Alharthy ◽  
Omar A El Meligy
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Bonding Agent ◽  
Micro Ct ◽  
Group Iii ◽  
Group I ◽  
Significant Difference ◽  
Sealant Retention

Objectives: To investigate the effect of Co-curing versus Staged-curing and No-bonding on retention of different resin-based sealants (RBS). Study design: For shear bond strength (SBS) and microleakage tests, 90 extracted premolars were divided equally into 3 groups (I, II, III). Each group was further subdivided equally into 3 subgroups (a, b, c). No-bonding subgroups did not receive a bonding agent, Staged-curing subgroups received a bonding agent that was cured before sealant application, while Co-curing subgroups received a bonding agent that was cured after sealant application. Seal-it was applied for group I, Helioseal-F for group II and Clinpro for group III. SBS buttons were tested using Instron machine, while microleakage specimens were examined using micro-CT. Results: Clinpro showed the highest SBS values in Staged-curing and No-bonding groups (8.72±2.39, 12.51±3.16) respectively. Staged-curing was significantly greater in SBS values than those for other groups (P&lt;0.05). There was a significant difference in microleakage values of Staged-curing among different RBS (P = 0.003), while there was no significant difference in values of No-bonding and Co-curing among different RBS (P = 0.541, P = 0.521). Conclusions: The use of a bonding agent as Staged-curing was more effective in improving sealant retention than No-bonding and Co-curing.

scholarly journals Indirect versus Direct Bonding—A Shear Bond Strength Comparison: An in vitro Study

2011 ◽  
Vol 12 (4) ◽  
pp. 232-238 ◽  
Author(s):  
Vinaya S Pai ◽  
S Nandini ◽  
M Swetha ◽  
N Sanjay
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Adhesive System ◽  
Vitro Study ◽  
Tooth Surface ◽  
Indirect Bonding ◽  
Significant Difference ◽  
Bonding Technique

ABSTRACT Aim The process of bonding orthodontic appliances to the enamel surface of the teeth has come to the forefront as a major improvement in bonding techniques. The purpose of this study is to compare the shear bond strength of stainless steel orthodontic brackets bonded using conventional direct bonding and indirect bonding as described by Thomas. Materials and methods Forty sound human premolars were divided into two groups of 20 each. Group I samples were bonded directly on the tooth surface using concise two paste adhesive system after etching and drying. Group II samples were bonded indirectly on the tooth surface according to Thomas indirect bonding technique using concise two paste adhesive system. The stored specimen was tested for shear bond strength in an Instron universal testing machine at a crosshead speed of 0.5 mm/minute. Data obtained were subjected to statistical analysis. Results The results showed that there was no statistically significant difference in the shear bond strength between direct and indirect bonding techniques. Chi-square test showed that there were significant differences among the adhesive remnant index scores between direct and indirect bonding groups. Conclusion In vitro shear bond strength comparison between direct and indirect-bonded attachments showed no significant difference between the two groups. Bond strength obtained with Thomas indirect bonding technique was comparable with direct bonding technique. Clinical significance Thomas indirect bonding technique can be used for bonding of the posterior teeth, where the risk of moisture contamination is high during bonding. How to cite this article Swetha M, Pai VS, Sanjay N, Nandini S. Indirect versus Direct Bonding—A Shear Bond Strength Comparison: An in vitro Study. J Contemp Dent Pract 2011; 12(4):232-238.

Sign in / Sign up

Export Citation Format

Share Document