scholarly journals Influence of coarse aggregate on the shear strength of reinforced concrete beams

2020 ◽  
Author(s):  
◽  
Hoosen Ahmed Jajbhay
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Coarse Aggregate ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Shear Reinforcement ◽  
Shear Transfer ◽  
Coarse Aggregates

Research to accurately predict the shear capacity of reinforced concrete beams without shear reinforcement has been ongoing since the early 20th century. Aggregate interlock of the coarse aggregates at the shear crack interface is one of the internal mechanisms of shear transfer and a major contributor to the shear capacity of slender beams. It is plausible, therefore, to investigate if the coarse aggregate itself influences the shear capacity of a concrete beam. The influence of the type of coarse aggregate on the shear capacity of beams without shear reinforcement was investigated in this study. From the literature study an understanding of the properties of coarse aggregates was gained, the internal mechanisms of shear transfer in reinforced concrete beams without shear reinforcement were determined, and the parameters influencing shear strength were identified. Based on this information an experimental program was designed. Eighteen reinforced concrete beams without shear reinforcement were cast. The beams were cast from three different types of coarse aggregates commonly used in the Durban area, i.e., dolerite, quartzite and tillite. For each type of coarse aggregate two variations were tested, i.e., 13 mm and 19 mm maximum aggregate sizes. For each size of coarse aggregate, three concrete strengths were tested. The beams were loaded in a beam press, by applying an increasing point load offset from midspan to induce cracking on the shorter side, until shear failure of the beam occurred. For the three concrete strengths, beams cast from dolerite had the highest shear capacity while beams cast from tillite had less shear capacity than beams cast from quartzite coarse aggregate. Furthermore, beams cast from 13 mm maximum size coarse aggregate had higher shear capacity than beams cast from 19 mm aggregate. The conclusion may be drawn that the type and size of coarse aggregate does influence the shear strength of a reinforced concrete beam without shear reinforcement.

scholarly journals Influence of Steel Fiber on the Shear Strength of a Concrete Beam

2018 ◽  
Vol 4 (7) ◽  
pp. 1501 ◽  
Author(s):  
Ali Ammar Hameed ◽  
Mohannad Husain Al-Sherrawi
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Shear Reinforcement

The shear failure in a concrete beam is a brittle type of failure. The addition of steel fibers in a plain concrete mix helps to bridge and restrict the cracks formed in the brittle concrete under applied loads, and enhances the ductility of the concrete. In this research an attempt was made to investigate the behavior and the ultimate shear strength of hooked end steel fiber reinforced concrete beams without traditional shear reinforcement. Four simply-supported reinforced concrete beams with a shear span-to-depth ratio of about 3.0 were tested under two-point loading up to failure. Steel fibers volumetric fractions that used were 0.0, 0.5, 0.75 and 1.0%. Test results indicated that using 1.0% volume fraction of hooked steel fiber led to exclude shear failure and enhanced the use of steel fibers as shear reinforcement in concrete beams. The results also showed that a concrete beam with hooked steel fiber provided higher post-flexural-cracking stiffness, an increase in the shear capacity and energy absorption and an increase in the maximum concrete and steel reinforcement strains.

scholarly journals Statistical and Reliability Study on Shear Strength of Recycled Coarse Aggregate Reinforced Concrete Beams

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3321
Author(s):  
Hyunjin Ju ◽  
Meirzhan Yerzhanov ◽  
Alina Serik ◽  
Deuckhang Lee ◽  
Jong R. Kim
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Construction Material ◽  
Safety Margin ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Construction And Demolition Waste ◽  
Demolition Waste ◽  
Rc Structures ◽  
Coarse Aggregates

The consumption of structural concrete in the construction industry is rapidly growing, and concrete will remain the main construction material for increasing urbanization all over the world in the near future. Meanwhile, construction and demolition waste from concrete structures is also leading to a significant environmental problem. Therefore, a proper sustainable solution is needed to address this environmental concern. One of the solutions can be using recycled coarse aggregates (RCA) in reinforced concrete (RC) structures. Extensive research has been conducted in this area in recent years. However, the usage of RCA concrete in the industry is still limited due to the absence of structural regulations appropriate to the RCA concrete. This study addresses a safety margin of RCA concrete beams in terms of shear capacity which is comparable to natural coarse aggregates (NCA) concrete beams. To this end, a database for reinforced concrete beams made of recycled coarse aggregates with and without shear reinforcement was established, collecting the shear specimens available from various works in the existing literature. The database was used to statistically identify the strength margin between RCA and NCA concrete beams and to calculate its safety margin based on reliability analysis. Moreover, a comparability study of RCA beams was conducted with its control specimens and with a database for conventional RC beams.

Predicting the effect of stirrups on shear strength of reinforced normal-strength concrete (NSC) and high-strength concrete (HSC) slender beams using artificial intelligence

2006 ◽  
Vol 33 (8) ◽  
pp. 933-944 ◽  
Author(s):  
H El Chabib ◽  
M Nehdi ◽  
A Saïd
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
High Strength ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Design Parameters ◽  
Rc Beams ◽  
Shear Reinforcement ◽  
Strength Concrete ◽  
Shear Design

The exact effect that each of the basic shear design parameters exerts on the shear capacity of reinforced concrete (RC) beams without shear reinforcement (Vc) is still unclear. Previous research on this subject often yielded contradictory results, especially for reinforced high-strength concrete (HSC) beams. Furthermore, by simply adding Vc and the contribution of stirrups Vs to calculate the ultimate shear capacity Vu, current shear design practice assumes that the addition of stirrups does not alter the effect of shear design parameters on Vc. This paper investigates the validity of such a practice. Data on 656 reinforced concrete beams were used to train an artificial neural network model to predict the shear capacity of reinforced concrete beams and evaluate the performance of several existing shear strength calculation procedures. A parametric study revealed that the effect of shear reinforcement on the shear strength of RC beams decreases at a higher reinforcement ratio. It was also observed that the concrete contribution to shear resistance, Vc, in RC beams with shear reinforcement is noticeably larger than that in beams without shear reinforcement, and therefore most current shear design procedures provide conservative predictions for the shear strength of RC beams with shear reinforcement.Key words: analysis, artificial intelligence, beam depth, compressive strength, modeling, shear span, shear strength.

Experimental Research on Crazing-Resistance of Inclined Section of Basalt Fiber Reinforced Concrete Beams

2014 ◽  
Vol 584-586 ◽  
pp. 899-903
Author(s):  
Wei Chen ◽  
Xiang Peng Li ◽  
Ting Ting Chen ◽  
Xiao Yang Wang ◽  
Chao Chao Ma
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Basalt Fiber ◽  
Volume Ratio ◽  
Reinforced Concrete Beam ◽  
Shear Capacity ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced

In order to research the influence of the shear capacity of reinforced concrete beam with the incorporation of basalt fiber, four basalt fiber reinforced concrete beams with parameters of length and volume ratio were designed and made. The fiber lengths were 12mm and 30mm, and the volume ratios were 1‰ and 2‰. The test data of basalt fiber reinforced concrete was obtained through the shear experiments and comparison with the common reinforced concrete beam. The results of the experiment show that the cracking load of the basalt fiber reinforced concrete beam increase obviously with the growing of fiber characteristic parameters, and effectively reduce the diagonal crack width.

scholarly journals Behaviour of Reinforced Concrete Beams with Wire Mesh As Shear Reinforcement

2019 ◽  
Vol 8 (12) ◽  
pp. 781-784
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Wire Mesh ◽  
Shear Behaviour ◽  
Experimental Program ◽  
Shear Reinforcement ◽  
Loading System ◽  
Shear Performance

This paper presents a study of shear behaviour of reinforced concrete beams. The major parameters used were type of shear reinforcement, namely stirrups alone, wire mesh alone and combination of both wire mesh and stirrups as shear reinforcement. The replacement of wire mesh was done on the basis of weight with stirrups. The experimental program includes four beams. All the beams were tested using two point loading system. It is evident from the result that the use of wire mesh enhanced improved shear performance and bearing capacity in the examined beams. Beams with wire mesh as shear reinforcement and combination of both wire mesh and stirrups exhibited some amount of increase in shear capacity with respect to the beams with stirrups alone as shear reinforcement. Furthermore beams with wire mesh and combination of wire mesh and stirrups as reinforcement exhibited less number of crack patterns compared beams with stirrups.

scholarly journals Shear Performance of Reinforced Concrete Beams Affected by Satisfactory Composite-Recycled Aggregates

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1711
Author(s):  
Changyong Li ◽  
Na Liang ◽  
Minglei Zhao ◽  
Kunqi Yao ◽  
Jie Li ◽  
...  
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Shear Crack ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Recycled Aggregates ◽  
Shear Span ◽  
Model Code ◽  
Model Code 2010

This paper is the outcome of experiments on the shear performance of reinforced concrete beams with approved composite-recycled aggregates. The strength grade of composite-recycled aggregate concrete (CRAC) was between 30 MPa and 60 MPa. The shear span-to-depth ratio varied from 1 to 3. The adaptability of HRB400 rebar, with critical yield strength of 400 MPa, used as stirrups was also verified. As the composite technology overcame the shortcomings of recycled coarse aggregate, CRAC had similar mechanical properties with those of conventional concrete. Details on the shear behaviors of test beams under a four-point loading test are presented. The results indicated that the changes of CRAC strain, stirrup strain, and shear-crack width depended on the failure patterns, which are controlled by the shear-span to depth ratio. The stirrups yield at the failure of reinforced CRAC beams. The shear cracking resistance and the shear capacity of reinforced CRAC beams can be predicted by the statistical equations. Based on the design codes GB50010, ACI318-19, Model Code 2010 and DIN-1045-1-2008 for conventional reinforced concrete beams, the shear strengths provided by CRAC and stirrups are statistical analyzed. The rationality of the design equations is examined by the utilization level of shear strength provided by CRAC. The maximum shear-crack widths are extracted from the test data of reinforced CRAC beams at normal service state. Comparatively, by specifying the lower limit of shear strength provided by the CRAC with various shear-span to depth ratios, China code GB50010 gives a rational method for utilizing CRAC. Under the premise that the design of shear capacity would give considerations to meet the normal serviceability, the factored strength of HRB400 rebar should be 360 MPa for the calculation of shear strength provided by stirrups. The design methods in codes of GB50010, ACI318-19 and Model Code 2010 are conservative for the shear capacity of reinforced CRAC beams.

Sign in / Sign up

Export Citation Format

Share Document