scholarly journals Railway bridge survey

2021 ◽  
Vol 79 (1) ◽  
pp. 289-295
Author(s):  
C.C. Khasenov ◽  
◽  
M.Ya. Kvashnin ◽  
A.K. Kurbenova ◽  
O.D. Seitkazinov ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Spatial Location ◽  
Baseline Data ◽  
Scientific Article ◽  
Joint Work ◽  
Railway Line ◽  
Concrete Blocks ◽  
Concrete Filling ◽  
Concrete Elements ◽  
Supporting Structures

This scientific article addresses the issues of a survey of bridges in order to determine the need for reconstruction or repair measures at these facilities and to collect baseline data for the dismantling of railway reconstruction projects. Inspection of culverts is carried out in order to determine the need for the appointment of reconstructive or repair measures at these facilities and to collect baseline data for the development of railway reconstruction projects. An approximate list of survey work and measurements is given. The calculation models for the analysis of the stress-strain state (VAT) and the modal analysis of the structure are constructed according to the data provided in the form of working documentation for the structure in question. Models of reinforced concrete elements of the supporting structures of the overpass allow for the joint work of reinforcing elements and concrete filling. Concrete filling of structures of reinforced concrete blocks of superstructures of 16.5 m and 23.6 m, as well as frames and pedestals of intermediate supports of the overpass, are specified by volume elements. Reinforcing structural elements (frames, grids, wire bundles for prestressing concrete) of spans and structures of intermediate supports are defined by bar elements and take into account their spatial location in the concrete filling. The results of the calculation analysis of the supporting structures of the overpass through the single-track railway line are presented.

scholarly journals Influence analysis of the main types of defects and damages on bearing capacity in reinforced concrete elements and their research methods

2019 ◽  
Vol 22 (22) ◽  
pp. 24-29
Author(s):  
Maksym Lobodanov ◽  
Pavlo Vegera ◽  
Zinoviy Blikharskyy
Keyword(s):  
Composite Material ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Strain State ◽  
Complete Separation ◽  
Building Structures ◽  
Joint Work ◽  
Economic Trends ◽  
Single Method ◽  
Concrete Elements

Abstract In current economic trends, changes in construction using are required. It usually leads to changes in value and type of the working load on building structures, with the requirement to rate the technical state and replace or strengthen the elements. An important aspect of determining the residual bearing capacity of damaged bending reinforced concrete elements is the research concerning the influence of difference defects and damages on the change of strength and deformability. In the article main types of damages and defects, methods of studies of damaged reinforced concrete elements and the expediency of usage of this elements are described. However, most methods are suitable only for certain defects and damages due to the large complexity of calculations and the consideration of multifactoriality. Significant complexity of a single method for calculating damaged elements depends on the possible changing stress strain state of an element in combination with certain defects and damages, the presence of a non-complete separation where during loading or alteration of the damaged element the fractions become included in the work, reinforced concrete is the composite material which carrying complexity in calculating the joint work of its components.

Methodology of studying the mechanical properties of composite materials (reinforced concrete)

2018 ◽  
Vol 84 (12) ◽  
pp. 61-67
Author(s):  
V. A. Eryshev
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Experimental Studies ◽  
Analytical Relationship ◽  
Hardened Concrete ◽  
Deformation Model ◽  
Joint Work ◽  
Concrete Shrinkage ◽  
Axial Tension ◽  
Tension And Compression

The mechanical properties of a complex composite material formed by steel and hardened concrete, are studied. A technique of operative quality control of new credible concrete and reinforcement, both in laboratory and field conditions is developed for determination of the strength and strain characteristics of materials, as well as cohesion forces determining their joint operation under load. The design of the mobile unit is presented. The unit provides a possibility of changing the direction of loading and testing the reinforced element of the given shape both for tension and compression. Moreover, the nomenclature of testing equipment and the number of molds for manufacturing concrete samples substantially decrease. Using the values of forcing resulting in concrete cracking when the joint work of concrete and reinforcement is disrupted the values of the inherent stresses and strains attributed to the concrete shrinkage are determined. An analytical relationship between the forces and deformations of the reinforced concrete sample with central reinforcement is derived for axial tension and compression, with allowance for strains and stresses in the reinforcement and concrete resulted from concrete shrinkage. The results of experimental studies are presented, including tension diagrams and diagrams of developing axial deformations with an increase in the load under the central loading of the reinforced elements. A methodology of accounting for stresses and deformations resulted from concrete shrinkage is developed. The applicability of the derived analytical relationships between stresses and deformations on the material diagrams to calculations of the reinforced concrete structures in the framework of the deformation model is estimated.

Use of Foam Polystyrene Waste in the Conditions of a Reinforced Concrete Products Factory

2020 ◽  
pp. 49-52
Author(s):  
S.E. YANUTINA ◽  
Keyword(s):  
Reinforced Concrete ◽  
Precast Concrete ◽  
Expanded Polystyrene ◽  
Insulation Material ◽  
Design Strength ◽  
Foam Polystyrene ◽  
Secondary Use ◽  
Concrete Blocks ◽  
Polystyrene Waste ◽  
Factory Laboratory

The relevance of research in the factory laboratory of JSC «198 KZHI», which is part of the HC GVSU «Center», is dictated by the need to dispose of foam polystyrene waste that occurs in large quantities when producing the precast concrete. In the production of three-layer external wall panels, polystyrene heatinsulating plates of the PPS 17-R-A brand are used as an effective insulation material. The secondary use of PPS 17-R-A for its intended purpose, as a heater, is not possible. The volume of foam polystyrene produced varies from 25 to 45 m3 per month. Utilization (disposal) of foam polystyrene waste is an expensive undertaking. Its use as a filler in the production of expanded polystyrene blocks was tested in the factory’s laboratory to produce foam polystyrene concrete with specified physical and mechanical characteristics. The results of testing of expanded polystyrene concrete of classes B2.5 and B 7.5 are presented. It is shown that under the conditions of the reinforced concrete factory technology, the production of polystyrene concrete blocks is possible with the achievement of the design strength. The information presented in the article is aimed at motivating specialists who produce recast concrete to the possibility of using foam polystyrene waste for low-rise construction. Keywords: foam polystyrene, ecology, energy efficiency, foam polystyrene concrete, foam polystyrene heat insulation plates, precast concrete.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

scholarly journals Application of artificial neural networks to predict the deflections of reinforced concrete beams

2016 ◽  
Vol 38 (2) ◽  
pp. 37-46 ◽  
Author(s):  
Mateusz Kaczmarek ◽  
Agnieszka Szymańska
Keyword(s):  
Neural Network ◽  
Neural Networks ◽  
Artificial Neural Network ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
The Neural Network ◽  
Eurocode 2 ◽  
Artificial Neural ◽  
Concrete Elements

Abstract Nonlinear structural mechanics should be taken into account in the practical design of reinforced concrete structures. Cracking is one of the major sources of nonlinearity. Description of deflection of reinforced concrete elements is a computational problem, mainly because of the difficulties in modelling the nonlinear stress-strain relationship of concrete and steel. In design practise, in accordance with technical rules (e.g., Eurocode 2), a simplified approach for reinforced concrete is used, but the results of simplified calculations differ from the results of experimental studies. Artificial neural network is a versatile modelling tool capable of making predictions of values that are difficult to obtain in numerical analysis. This paper describes the creation and operation of a neural network for making predictions of deflections of reinforced concrete beams at different load levels. In order to obtain a database of results, that is necessary for training and testing the neural network, a research on measurement of deflections in reinforced concrete beams was conducted by the authors in the Certified Research Laboratory of the Building Engineering Institute at Wrocław University of Science and Technology. The use of artificial neural networks is an innovation and an alternative to traditional methods of solving the problem of calculating the deflections of reinforced concrete elements. The results show the effectiveness of using artificial neural network for predicting the deflection of reinforced concrete beams, compared with the results of calculations conducted in accordance with Eurocode 2. The neural network model presented in this paper can acquire new data and be used for further analysis, with availability of more research results.

Sign in / Sign up

Export Citation Format

Share Document