scholarly journals Synergetic aerosol retrieval from SCIAMACHY and AATSR onboard ENVISAT

2008 ◽  
Vol 8 (1) ◽  
pp. 2903-2951 ◽  
Author(s):  
T. Holzer-Popp ◽  
M. Schroedter-Homscheidt ◽  
H. Breitkreuz ◽  
D. Martynenko ◽  
L. Klüser
Keyword(s):  
Information Content ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Surface Brightness ◽  
Dark Field ◽  
Water Soluble ◽  
Least Square ◽  
Aerosol Retrieval ◽  
First Case ◽  
Satellite Platform

Abstract. The synergetic aerosol retrieval method SYNAER (Holzer-Popp et al., 2002a) has been extended to the use of ENVISAT measurements. It exploits the complementary information of a radiometer and a spectrometer onboard one satellite platform to extract aerosol optical depth (AOD) and speciation (as choice from a representative set of pre-defined mixtures of water-soluble, soot, mineral dust, and sea salt components). SYNAER consists of two retrieval steps. In the first step the radiometer is used to do accurate cloud screening, and subsequently to quantify the aerosol optical depth (AOD) at 550 nm and spectral surface brightness through a dark field technique. In the second step the spectrometer is applied to choose the most plausible aerosol type through a least square fit of the measured spectrum with simulated spectra using the AOD and surface brightness retrieved in the first step. This method was developed and a first case study evaluation against few (15) multi-spectral ground-based AERONET sun photometer observations was conducted with a sensor pair (ATSR-2 and GOME) onboard ERS-2. However, due to instrumental limitations the coverage of SYNAER/ERS-2 and the AERONET network in 1997/98 is very sparse and thus only few coincidences with AERONET were found. Therefore, SYNAER was transferred to similar sensors AATSR and SCIAMACHY onboard ENVISAT. While transferring to the new sensor pair a thorough evaluation of the synergetic methodology and its information content has been conducted, which led to significant improvements in the methodology: an update of the aerosol model, an improved cloud detection, and an enhanced dark field albedo characterization. This paper describes the information content analysis and these improvements in detail and presents first results of applying the SYNAER methodology to AATSR and SCIAMACHY.

scholarly journals Improvements of synergetic aerosol retrieval for ENVISAT

2008 ◽  
Vol 8 (24) ◽  
pp. 7651-7672 ◽  
Author(s):  
T. Holzer-Popp ◽  
M. Schroedter-Homscheidt ◽  
H. Breitkreuz ◽  
D. Martynenko ◽  
L. Klüser
Keyword(s):  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Surface Brightness ◽  
Dark Field ◽  
Water Soluble ◽  
Aerosol Composition ◽  
Aerosol Retrieval ◽  
First Case ◽  
Satellite Platform ◽  
Version 2.0

Abstract. The synergetic aerosol retrieval method SYNAER (Holzer-Popp et al., 2002a) has been extended to the use of ENVISAT measurements. It exploits the complementary information of a radiometer and a spectrometer onboard one satellite platform to extract aerosol optical depth (AOD) and speciation (as a choice from a representative set of pre-defined mixtures of water-soluble, soot, mineral dust, and sea salt components). SYNAER consists of two retrieval steps. In the first step the radiometer is used for accurate cloud screening, and subsequently to quantify the aerosol optical depth (AOD) at 550 nm and spectral surface brightness through a dark field technique for different pre-defined aerosol mixtures. In the second step the spectrometer is applied to choose the most plausible aerosol mixture through a least square fit of the measured spectrum with simulated spectra using the mixture-dependent values of AOD and surface brightness retrieved in the first step. This method was developed and a first case study evaluation against few (15) multi-spectral ground-based AERONET sun photometer observations was conducted with a sensor pair (ATSR-2 and GOME) onboard ERS-2. Due to instrumental limitations the coverage of SYNAER/ERS-2 is very sparse. Therefore, SYNAER was transferred to similar sensors AATSR and SCIAMACHY onboard ENVISAT. While transferring to the new sensor pair significant improvements in the methodology were made based on a thorough evaluation of the methodology: (1) an update of the aerosol model, (2) improved cloud detection in the tropics and sub tropics, and (3) an enhanced dark field albedo characterization. This paper describes these improvements in detail and assesses their combined impact on the results. After a brief assessment of atmospheric noise impact on comparisons of pixel and station measurements a validation against ground-based measurements establishes error bars for the SYNAER/ENVISAT method version 2.0. A theoretical analysis of the information content with regard to aerosol composition (second retrieval step) is presented to quantify the potential and limitations of this new capability provided by the SYNAER method. Building on this analysis, first seasonal and monthly composition results calculated by applying SYNAER version 2.0 to AATSR and SCIAMACHY are shown to demonstrate the potential of the approach. An inter-comparison to earlier results of SYNAER version 1.0 is made for both the validation and the example datasets.

scholarly journals Understanding the aerosol information content in multi-spectral reflectance measurements using a synergetic retrieval algorithm

2010 ◽  
Vol 3 (6) ◽  
pp. 1589-1598 ◽  
Author(s):  
D. Martynenko ◽  
T. Holzer-Popp ◽  
H. Elbern ◽  
M. Schroedter-Homscheidt
Keyword(s):  
Content Analysis ◽  
Information Content ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Degrees Of Freedom ◽  
Surface Albedo ◽  
Water Soluble ◽  
Retrieval Algorithm ◽  
Aerosol Types ◽  
Reflectance Measurements

Abstract. An information content analysis for multi-wavelength SYNergetic AErosol Retrieval algorithm SYNAER was performed to quantify the number of independent pieces of information that can be retrieved. In particular, the capability of SYNAER to discern various aerosol types is assessed. This information content depends on the aerosol optical depth, the surface albedo spectrum and the observation geometry. The theoretical analysis is performed for a large number of scenarios with various geometries and surface albedo spectra for ocean, soil and vegetation. When the surface albedo spectrum and its accuracy is known under cloud-free conditions, reflectance measurements used in SYNAER is able to provide for 2–4° of freedom that can be attributed to retrieval parameters: aerosol optical depth, aerosol type and surface albedo. The focus of this work is placed on an information content analysis with emphasis to the aerosol type classification. This analysis is applied to synthetic reflectance measurements for 40 predefined aerosol mixtures of different basic components, given by sea salt, mineral dust, biomass burning and diesel aerosols, water soluble and water insoluble aerosols. The range of aerosol parameters considered through the 40 mixtures covers the natural variability of tropospheric aerosols. After the information content analysis performed in Holzer-Popp et al. (2008) there was a necessity to compare derived degrees of freedom with retrieved aerosol optical depth for different aerosol types, which is the main focus of this paper. The principle component analysis was used to determine the correspondence between degrees of freedom for signal in the retrieval and derived aerosol types. The main results of the analysis indicate correspondence between the major groups of the aerosol types, which are: water soluble aerosol, soot, mineral dust and sea salt and degrees of freedom in the algorithm and show the ability of the SYNAER to discern between this aerosol types. The results of the work will be further used for the development of the promising methodology of the construction error covariance matrices in the assimilation system.

scholarly journals Retrieval of aerosol optical depth over land surfaces from AVHRR data

2013 ◽  
Vol 6 (1) ◽  
pp. 2227-2251 ◽  
Author(s):  
L. Mei ◽  
Y. Xue ◽  
A. A. Kokhanovsky ◽  
W. von Hoyningen-Huene ◽  
G. de Leeuw ◽  
...  
Keyword(s):  
Time Series ◽  
High Resolution ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Surface Reflectance ◽  
Aerosol Retrieval ◽  
Avhrr Data ◽  
Land Surfaces ◽  
Very High

Abstract. The Advanced Very High Resolution Radiometer (AVHRR) radiance data provide a global, long-term, consistent time series having high spectral and spatial resolution and thus being valuable for the retrieval of surface spectral reflectance, albedo and surface temperature. Long term time series of such data products are necessary for studies addressing climate change, sea ice distribution and movement, and ice sheet coastal configuration. These data have also been used to retrieve aerosol properties over ocean and land surfaces. However, the retrieval of aerosol over land and land surface albedo are challenging because of the information content of the measurement is limited and the inversion of these data products being ill defined. Solving the radiative transfer equations requires additional information and knowledge to reduce the number of unknowns. In this contribution we utilise an empirical linear relationship between the surface reflectances in the AVHRR channels at wavelengths of 3.75 μm and 2.1 μm, which has been identified in Moderate Resolution Imaging Spectroradiometer (MODIS) data. Next, following the MODIS dark target approach, the surface reflectance at 0.64 μm was obtained. The comparison of the estimated surface reflectance at 0.64 μm with MODIS reflectance products (MOD09) shows a strong correlation (R = 0.7835). Once this was established, the MODIS "dark-target" aerosol retrieval method was adapted to Advanced Very High Resolution Radiometer (AVHRR) data. A simplified Look-Up Table (LUT) method, adopted from Bremen AErosol Retrieval (BAER) algorithm, was used in the retrieval. The Aerosol Optical Depth (AOD) values retrieved from AVHRR with this method compare favourably with ground-based measurements, with a correlation coefficient R = 0.861 and Root Mean Square Error (RMSE) = 0.17. This method can be easily applied to other satellite instruments which do not have a 2.1 μm channel, such as those currently planned to geostationary satellites.

scholarly journals Retrieval of aerosol optical depth over land surfaces from AVHRR data

2014 ◽  
Vol 7 (8) ◽  
pp. 2411-2420 ◽  
Author(s):  
L. L. Mei ◽  
Y. Xue ◽  
A. A. Kokhanovsky ◽  
W. von Hoyningen-Huene ◽  
G. de Leeuw ◽  
...  
Keyword(s):  
Time Series ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Limited Information ◽  
Additional Information ◽  
Aerosol Retrieval ◽  
Avhrr Data ◽  
Moderate Resolution Imaging Spectroradiometer ◽  
Land Surfaces

Abstract. The Advanced Very High Resolution Radiometer (AVHRR) provides a global, long-term, consistent time series of radiance data in several wavebands which are used for the retrieval of surface spectral reflectance, albedo and surface temperature. Long-term time series of such data products are necessary for studies addressing climate change, sea ice distribution and movement, and ice sheet coastal configuration. AVHRR radiances have also been used to retrieve aerosol properties over ocean and land surfaces. However, the retrieval of aerosol over land is challenging because of the limited information content in the data which renders the inversion problem ill defined. Solving the radiative transfer equations requires additional information to reduce the number of unknowns. In this contribution we utilise an empirical linear relationship between the surface reflectances in the AVHRR channels at wavelengths of 3.75 μm and 2.1 μm, which has been identified in the Moderate Resolution Imaging Spectroradiometer (MODIS) data. Following the MODIS dark target approach, this relationship is used to obtain the surface reflectance at 0.64 μm. The comparison of the estimated surface reflectances with MODIS reflectance products (MOD09) shows a strong correlation. Once this was established, the MODIS "dark-target" aerosol retrieval method was adapted to AVHRR data. A simplified look-up table (LUT) method, adopted from the Bremen AErosol Retrieval (BAER) algorithm, was used in the retrieval. The aerosol optical depth (AOD) values retrieved from AVHRR with this method compare favourably with ground-based measurements, with 71.8% of the points located within ±(0.1 + 0.15τ) (τ is the AOD) of the identity line. This method can be easily applied to other satellite instruments which do not have a 2.1 μm channel, such as those currently planned to be used on geostationary satellites.

scholarly journals Validation of MODIS 3 km Land Aerosol Optical Depth from NASA's EOS Terra and Aqua Missions

2018 ◽  
Author(s):  
Pawan Gupta ◽  
Lorraine A. Remer ◽  
Robert C. Levy ◽  
Shana Mattoo
Keyword(s):  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Retrieval Algorithm ◽  
Data Sets ◽  
Aerosol Retrieval ◽  
Moderate Resolution ◽  
Resolution Imaging ◽  
Moderate Resolution Imaging Spectroradiometer ◽  
Sensor Degradation ◽  
Over Time

Abstract. The two MODerate Resolution Imaging Spectroradiometer (MODIS) sensors, aboard Earth Observing Satellites (EOS) Terra and Aqua, have been making aerosol observations for more than 15 years. From these observations, the MODIS dark target (DT) aerosol retrieval algorithm provides aerosol optical depth (AOD) products, globally over both land and ocean. In addition to the standard resolution product (10 × 10 km2), the MODIS collection 6 (C006) data release included a higher resolution (3 × 3 km2). Other than accommodations for the two different resolutions, the 10 km, and 3 km DT algorithms are basically the same. In this study, we perform global validation of the higher resolution AOD over global land by comparing against AERONET measurements. The MODIS-AERONET collocated data sets consist of 161,410 high-confidence AOD pairs from 2000 to 2015 for MODIS Terra and 2003 to 2015 for MODIS-Aqua. We find that 62.5 % and 68.4 % of AODs retrieved from MODIS-Terra and MODIS-Aqua, respectively, fall within previously published expected error bounds of ±(0.05 + 0.2*AOD), with a high correlation (R = 0.87). The scatter is not random but exhibits a mean positive bias of ~ 0.06 for Terra and ~ 0.03 for Aqua. These biases for the 3 km product are approximately 0.03 larger than the biases found in similar validations of the 10 km product. The validation results for the 3 km product did not have a relationship to aerosol loading (i.e. true AOD) but did exhibit dependence on quality flags, region, viewing geometry, and aerosol spatial variability. Time series of global MODIS-AERONET differences show that validation is not static, but has changed over the course of both sensors' lifetimes, with MODIS-Terra showing more change over time. The likely cause of the change of validation over time is sensor degradation, but changes in the distribution of AERONET stations and differences in the global aerosol system itself could be contributing to the temporal variability of validation.

scholarly journals Understanding the aerosol information content in multi-spectral reflectance measurements using a synergetic retrieval algorithm

2010 ◽  
Vol 3 (3) ◽  
pp. 2579-2602 ◽  
Author(s):  
D. Martynenko ◽  
T. Holzer-Popp ◽  
H. Elbern ◽  
M. Schroedter-Homscheidt
Keyword(s):  
Content Analysis ◽  
Information Content ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Degrees Of Freedom ◽  
Surface Albedo ◽  
Retrieval Algorithm ◽  
Multi Wavelength ◽  
Aerosol Types ◽  
Reflectance Measurements

Abstract. The multi-wavelength SYNergetic AErosol Retrieval algorithm SYNAER (Holzer-Popp et al., 2002) is used to retrieve aerosol parameters from the Advanced Along Tracking Scanning Radiometer (AATSR) and the Scanning Imaging Absorption Spectrometer for Atmospheric CHartographY (SCIAMACHY). An information content analysis (Holzer-Popp et al., 2008) was performed to quantify the number of independent pieces of information can be retrieved from the combined reflectance measurements of aerosols by both instruments. In particular, the capability of SYNAER to discern various aerosol types is assessed. The focus of this work is further placed on an information content analysis with emphasis to the aerosol type classification. This analysis is applied to synthetic reflectance measurements for 40 predefined aerosol mixtures of different basic components, given by sea salt, mineral dust, biomass burning and diesel aerosols, water soluble and water insoluble aerosols. The range of aerosol parameters considered through the 40 mixtures covers the natural variability of tropospheric aerosols. In this work the capability of the multi-wavelength algorithm to discern aerosol types is investigated. After the information content analysis performed in Holzer-Popp et al. (2008) there was a necessity to compare derived degrees of freedom with retrieved aerosol optical depth for different aerosol types, which is the main focus of this paper. This information content depends on the aerosol optical depth, the surface albedo spectrum and the observation geometry. This theoretical analysis is performed for a large number of scenarios with various geometries and surface albedo spectra for ocean, soil and vegetation. When the surface albedo spectrum and its accuracy is known under cloud-free conditions, reflectance measurements used in SYNAER is able to provide for 2 to 4 degrees of freedom that can be attributed to retrieval parameters: aerosol optical depth, aerosol type and surface albedo.

scholarly journals Intercomparison of column aerosol optical depths from CALIPSO and MODIS-Aqua

2011 ◽  
Vol 4 (2) ◽  
pp. 131-141 ◽  
Author(s):  
C. Kittaka ◽  
D. M. Winker ◽  
M. A. Vaughan ◽  
A. Omar ◽  
L. A. Remer
Keyword(s):  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Orthogonal Polarization ◽  
Aerosol Layer ◽  
Aerosol Retrieval ◽  
Modis Aod ◽  
Seasonal Basis ◽  
Selection Of ◽  
Good Agreement

Abstract. The Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) is carried on the CALIPSO satellite and has acquired global aerosol profiles since June 2006. CALIPSO is flown in formation with the Aqua satellite as part of the A-train satellite constellation, so that a large number of coincident aerosol observations are available from CALIOP and the MODIS-Aqua instrument. This study compares column aerosol optical depth at 0.532 μm derived from CALIOP aerosol profiles with MODIS-Aqua 0.55 μm aerosol optical depth over the period June 2006 through August 2008. The study is based on the CALIOP Version 2 Aerosol Layer Product and MODIS Collection 5. While CALIOP is first and foremost a profiling instrument, this comparison of column aerosol optical depth provides insight into quality of CALIOP aerosol data. It is found that daytime aerosol optical depth from the CALIOP Version 2 product has only a small global mean bias relative to MODIS Collection 5. Regional biases, of both signs, are larger and biases are seen to vary somewhat with season. Good agreement between the two sensors in ocean regions with low cloudiness suggests that the selection of lidar ratios used in the CALIOP aerosol retrieval is sufficient to provide a regional mean AOD consistent with that retrieved from MODIS. Although differences over land are observed to be larger than over ocean, the bias between CALIOP and MODIS AOD on a regional-seasonal basis is found to be roughly within the envelope of the MODIS expected uncertainty over land and ocean. This work forms a basis for further comparisons using the recently released CALIOP Version 3 data.

scholarly journals Theoretical Uncertainty Analysis of Satellite Retrieved Aerosol Optical Depth Associated with Surface Albedo and Aerosol Optical Properties

2021 ◽  
Vol 13 (3) ◽  
pp. 344
Author(s):  
Jingting Huang ◽  
William Patrick Arnott ◽  
James C. Barnard ◽  
Heather A. Holmes
Keyword(s):  
Optical Properties ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Asymmetry Parameter ◽  
Surface Albedo ◽  
Single Scattering ◽  
Critical Surface ◽  
Surface Reflectance ◽  
Aerosol Optical Properties ◽  
Aerosol Retrieval

Deriving aerosol optical depth (AOD) from space-borne observations is still challenging due to uncertainties associated with sensor calibration drift, cloud screening, aerosol type classification, and surface reflectance characterization. As an initial step to understanding the physical processes impacting these uncertainties in satellite AOD retrievals, this study outlines a theoretical approach to estimate biases in the satellite aerosol retrieval algorithm affected by surface albedo and prescribed aerosol optical properties using a simplified radiative transfer model with a traditional error propagation approach. We expand the critical surface reflectance concept to obtain the critical surface albedo (CSA), critical single scattering albedo (CSSA), and critical asymmetry parameter (CAP). The top-of-atmosphere (TOA) reflectance is not sensitive to significant variability in aerosol loading (AOD) at the critical value; thus, the AOD cannot be determined. Results show that 5% bias in surface albedo (A), single scattering albedo (SSA), or asymmetry parameter (g) lead to large retrieved AOD errors, especially high under conditions when A, SSA, or g are close to their critical values. The results can be useful for future research related to improvements of satellite aerosol retrieval algorithms and provide a preliminary framework to analytically quantify AOD uncertainties from satellite retrievals.

scholarly journals Spectral Aerosol Optical Depth Retrievals by Ground-Based Fourier Transform Infrared Spectrometry

2020 ◽  
Vol 12 (19) ◽  
pp. 3148
Author(s):  
África Barreto ◽  
Omaira Elena García ◽  
Matthias Schneider ◽  
Rosa Delia García ◽  
Frank Hase ◽  
...  
Keyword(s):  
Fourier Transform ◽  
High Resolution ◽  
Aerosol Optical Depth ◽  
Optical Depth ◽  
Cross Validation ◽  
Mineral Dust ◽  
Fourier Transform Infrared ◽  
Water Soluble ◽  
Infrared Spectrometry ◽  
Low Resolution

Aerosol Optical Depth (AOD) and the Ångström Exponent (AE) have been calculated in the near infrared (NIR) and short-wave infrared (SWIR) spectral regions over a period of one year (May 2019–May 2020) at the high-mountain Izaña Observatory (IZO) from Fourier Transform Infrared (FTIR) solar spectra. The high-resolution FTIR measurements were carried out coincidentally with Cimel CE318-T photometric observations in the framework of the Aerosol Robotic Network (AERONET). A spectral FTIR AOD was generated using two different approaches: by means of the selection of seven narrow FTIR micro-windows (centred at 1020.90, 1238.25, 1558.25, 1636.00, 2133.40, 2192.00, and 2314.20 nm) with negligible atmospheric gaseous absorption, and by using the CE318-AERONET’s response function in the near-coincident bands (1020 nm and 1640 nm) to degrade the high-resolution FTIR spectra. The FTIR system was absolutely calibrated by means of a continuous Langley–Plot analysis over the 1-year period. An important temporal drift of the calibration constant was observed as a result of the environmental exposure of the FTIR’s external optical mirrors (linear degradation rate up to 1.75% month−1). The cross-validation of AERONET-FTIR databases documents an excellent agreement between both AOD products, with mean AOD differences below 0.004 and root-mean-squared errors below 0.006. A rather similar agreement was also found between AERONET and FTIR convolved bands, corroborating the suitability of low-resolution sunphotometers to retrieve high-quality AOD data in the NIR and SWIR domains. In addition, these results demonstrate that the methodology developed here is suitable to be applied to other FTIR spectrometers, such as portable and low-resolution FTIR instruments with a potentially higher spatial coverage. The spectral AOD dependence for the seven FTIR micro-windows have been also examined, observing a spectrally flat AOD behaviour for mineral dust particles (the typical atmospheric aerosols presented at IZO). A mean AE value of 0.53 ± 0.08 for pure mineral dust in the 1020–2314 nm spectral range was retrieved in this paper. A subsequent cross-validation with the MOPSMAP (Modeled optical properties of ensembles of aerosol particles) package has ensured the reliability of the FTIR dataset, with AE values between 0.36 to 0.60 for a typical mineral dust content at IZO of 100 cm−3 and water-soluble particle (WASO) content ranging from 600 to 6000 cm−3. The new database generated in this study is believed to be the first long-term time series (1-year) of aerosol properties generated consistently in the NIR and SWIR ranges from ground-based FTIR spectrometry. As a consequence, the results presented here provide a very promising tool for the validation and subsequent improvement of satellite aerosol products as well as enhance the sensitivity to large particles of the existing databases, required to improve the estimation of the aerosols’ radiative effect on climate.

Sign in / Sign up

Export Citation Format

Share Document