Development of numerical model of laser sensing of clear air turbulence (CAT) taking into account effects of the propagation of laser radiation in a random medium, molecular and aerosol scattering

Author(s):  
Alexey Mamontov ◽  
Oksana Koval ◽  
Viktor Kulikov

<p>We've  built a numerical model of the propagation and scattering of laser radiation in a turbulent medium, taking into account molecular and aerosol scattering . The model will be based on the method of random phase screens. In the framework of this method, the direct propagation of laser radiation is modeled by the method of stepwise splitting. For this purpose, a random medium is divided into layers, and each layer is presented as a composition of an infinitely thin phase screen and vacuum propagation. To simulate a random medium, random phase screens whose phase thickness is associated with the spectrum of random medium inhomogeneities will be used.</p><p>Modeling incoherent (molecular and aerosol) scattering is based on the principle of reciprocity. Since the Green function for the propagation problem in a random medium is symmetric with respect to the permutation of the source and receiver, the backscattering problem can be reduced to solving the direct radiation propagation problem. In this case, the summation of the contributions of elementary random scatterers are performed in an incoherent manner. </p><p>         In 2009–2015, with the support of the Commission of the European Communities, as part of the 7th framework program, the DELICAT project  (DEmonstration of LIdar based Clear Air Turbulence detection) was carried out . In the course of this project , a lidar was designed , manufactured and tested for installation on an airplane with the aim of early detection of clear sky turbulence . The emitted signal was polarized vertically. The scattered radiation was measured in two polarizations: vertical and horizontal. The experiment showed that the effects of aerosol scattering at given altitudes can almost never be neglected.</p><p>    To build an aerosol scattering model, the experimental data from the DELICAT project was analyzed . Spectral and cross-spectral analysis of measurements in two polarizations is already  performed. Cross-spectral analysis will evaluate the effects of radiation depolarization. A model of the aerosol scattering matrix describing the observed effects of depolarization was constructed. In particular, multicomponent models will be considered. The spatio-temporal properties of aerosol clouds are closely investigated and also  contribution of variations in the measurement geometry during the flight to measurement errors.</p><p>       The constructed numerical model shall make it possible to plan similar experiments in the future and better understand the role of aerosol and molecular scattering in the interpretation of experimental data in order to detect clear sky turbulence.</p><p>This work was supported by the RFBR grant No. 18-35-00368</p>

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 875
Author(s):  
Jie Wu ◽  
Yuri Hovanski ◽  
Michael Miles

A finite element model is proposed to investigate the effect of thickness differential on Limiting Dome Height (LDH) testing of aluminum tailor-welded blanks. The numerical model is validated via comparison of the equivalent plastic strain and displacement distribution between the simulation results and the experimental data. The normalized equivalent plastic strain and normalized LDH values are proposed as a means of quantifying the influence of thickness differential for a variety of different ratios. Increasing thickness differential was found to decrease the normalized equivalent plastic strain and normalized LDH values, this providing an evaluation of blank formability.


2000 ◽  
Vol 14 (16) ◽  
pp. 1669-1681 ◽  
Author(s):  
SANDEEP K. JOSHI ◽  
A. M. JAYANNAVAR

A study of statistics of transmission and reflection from a random medium with stochastic amplification as opposed to coherent amplification is presented. It is found that the transmission coefficient t, for sample length L less than the critical length L c grows exponentially with L. In the limit L→∞ transmission decays exponentially as < ln t>=-L/ξ where ξ is the localization length. In this limit reflection coefficient r saturates to a fixed value which shows a monotonic increase as a function of strength of amplification α. The stationary distribution of super-reflection coefficient agrees well with the analytical results obtained within the random phase approximation (RPA). Our model also exhibits the well known duality between absorption and amplification. We emphasize the major differences between coherent amplification and stochastic amplification where-ever appropriate.


2003 ◽  
Author(s):  
Alexander V. Novokhreshenov ◽  
Valery V. Bakutkin ◽  
Valery V. Tuchin ◽  
Vladimir P. Ryabukho ◽  
Irina L. Maksimova ◽  
...  

2021 ◽  
Vol 42 ◽  
pp. 128-134
Author(s):  
Daniela Pintilie ◽  
Iuliana Florina Pană ◽  
Adrian Malciu ◽  
Constantin Puică ◽  
Cristina Pupăză

High Explosive Mortar bombs are used on the battlefield for destroying the manpower, non-armoured equipment and shelters. The paper describes an original experimental and numerical approach regarding the potential threats caused by the detonation of 120 mm HE mortar bombs. The evaluation of the bomb effect presumes the fulfillment of experimental trials that focus on two physical mechanisms which appear after the detonation of the cased high explosive. These mechanisms are the shock wave generation and the fragments propulsion, which were also studied by a numerical model that provides results over the bomb fragmentation mode. The novelty of the paper consists in the calibrated 3D numerical model confirmed by the experimental data, which provides information over the fragmentation process of the case and the initial velocity of its fragments, proving that the main threat of this type of ammunition is the effect through metal fragments. The results of numerical simulation and experimental data are used for their comparative analysis and the assessment of the phenomena.


Author(s):  
Marcin Wikło ◽  
Przemysław Motyl ◽  
Krzysztof Olejarczyk ◽  
Krzysztof Kołodziejczyk ◽  
Rafał Kalbarczyk ◽  
...  

10.14311/450 ◽  
2003 ◽  
Vol 43 (4) ◽  
Author(s):  
P. Hasal ◽  
I. Fořt ◽  
J. Kratěna

Experimental data obtained by measuring the tangential component of the force affecting radial baffles in a flat-bottomed cylindrical mixing vessel stirred with a Rushton turbine impeller is analysed. Spectral analysis of the experimental data demonstrated the presence of its macro-instability (MI) related low-frequency component embedded in the total force. Two distinct dimensionless frequencies (both directly proportional to the impeller speed of rotation N) of the occurence of the MI component were detected: a lower frequency of approximately 0.025N and a higher frequency of about 0.085N. The relative magnitude QMI of the MI-related component of the total tangential force was evaluated by a combination of proper orthogonal decomposition (POD) and spectral analysis. The values of magnitude QMI varied in the interval [rom approximately 0.05 to 0.30. The magnitude QMI takes maximum values at low Reynolds number values (in laminar and transitional regions). In the turbulent region (ReM >20000) the QMI value is low and practically constant. The dependence oj the QMI values on vertical position in the vessel is only marginal. The results suggest that the magnitude of the MI component of the force is significantly influenced by the liquid viscosity and density.


2020 ◽  
Vol 8 (9) ◽  
pp. 728
Author(s):  
Said Alhaddad ◽  
Lynyrd de Wit ◽  
Robert Jan Labeur ◽  
Wim Uijttewaal

Breaching flow slides result in a turbidity current running over and directly interacting with the eroding, submarine slope surface, thereby promoting further sediment erosion. The investigation and understanding of this current are crucial, as it is the main parameter influencing the failure evolution and fate of sediment during the breaching phenomenon. In contrast to previous numerical studies dealing with this specific type of turbidity currents, we present a 3D numerical model that simulates the flow structure and hydrodynamics of breaching-generated turbidity currents. The turbulent behavior in the model is captured by large eddy simulation (LES). We present a set of numerical simulations that reproduce particular, previously published experimental results. Through these simulations, we show the validity, applicability, and advantage of the proposed numerical model for the investigation of the flow characteristics. The principal characteristics of the turbidity current are reproduced well, apart from the layer thickness. We also propose a breaching erosion model and validate it using the same series of experimental data. Quite good agreement is observed between the experimental data and the computed erosion rates. The numerical results confirm that breaching-generated turbidity currents are self-accelerating and indicate that they evolve in a self-similar manner.


2012 ◽  
Vol 468-471 ◽  
pp. 2248-2254
Author(s):  
Qiang Li ◽  
Wan Kui Bu ◽  
Hui Xu ◽  
Xiao Bo Song

The numerical model of top coal drawing in gently inclined seam is built based on PFC2d software. By comparing with the theory of drawn-body movement law, it can be obtained that the shape of top coal drawn-body accords with the theory of random medium movement. The research results show that the form of the shape equation of top coal drawn-body is uniform while the top coal caving angle is different. On the other hand, with the difference of top coal caving angle and drawing height, the shape of top coal drawn-body is differential at the meso scale, which depends on the parameters of the shape equation of top coal drawn-body.


1992 ◽  
Vol 285 ◽  
Author(s):  
W.W. Duley ◽  
G. Kinsman

ABSTRACTExcimer laser radiation may be used to process metal surfaces in a variety of novel ways. The simplest of these involves the use of UV laser pulses for ablation. Ablation occurs as the result of both vaporization and hydrodynamical effects. Experimental data related to these processes will be discussed. In addition, it will be shown how specific irradiation regimes can yield metal surfaces with unique radiative properties.


Sign in / Sign up

Export Citation Format

Share Document