scholarly journals DRYING CHARACTERISTICS, MINERAL CONTENT, TEXTURE AND SENSORIAL PROPERTIES OF PUMPKIN FRUIT LEATHER

2021 ◽  
Vol 51 (3) ◽  
pp. 193-201
Author(s):  
Azime Özkan Karabacak ◽  
Senem Suna ◽  
Saliha Dorak ◽  
Ömer Utku Çopur
Keyword(s):  
Mineral Content ◽  
Moisture Diffusivity ◽  
Drying Rate ◽  
Textural Features ◽  
Drying Time ◽  
Drying Characteristics ◽  
Hot Air ◽  
Thin Layer Drying ◽  
Drying Models ◽  
Thin Layer Drying Models

The objective of this study was to investigate the influences of hot air (HAD: 50, 60, 70°C), vacuum (VD: 50, 60, 70°C at 300 mbar) and microwave methods (MWD: 90, 180W) on drying characteristics, effective moisture diffusivity (Deff), mineral content, texture, and sensorial properties of pumpkin pestils. MWD led to the highest drying rate and the lowest drying time in all methods. Page and Modified Page were ideally fitted to experimental results among seven thin layer drying models. Mineral content (Ca, K, Na, P, Mg, Fe, Zn, Cu, Mn) of the pestils showed higher values than non-dried (paste) mixture. Significant differences were determined between textural features of the pestils (p < 0.05). Furthermore, products dried with HAD and VD were preferred rather than MWD in terms of sensorial properties.

Influence of Citric Acid Pretreatment on Drying of Peach Slices

2014 ◽  
Vol 10 (4) ◽  
pp. 829-837 ◽  
Author(s):  
İbrahim Doymaz ◽  
Betül Bilici
Keyword(s):  
Citric Acid ◽  
Moisture Diffusivity ◽  
Citric Acid Solution ◽  
Air Velocity ◽  
Acid Pretreatment ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying ◽  
Drying Models ◽  
Thin Layer Drying Models

Abstract The effect of citric acid pretreatment on the drying characteristics of peach slices was investigated in a cabinet dryer. The experiments were conducted on peach slices with a thickness of 5 mm at temperatures of 45, 55, 65 and 75°C with an air velocity of 2.0 m/s. The drying time of peach slices pretreated with citric acid solution was shorter than the control ones. The drying data were fitted to five thin-layer drying models. The results show that the Midilli et al. model was the most appropriate model for drying of peach slices. The values of effective moisture diffusivity were found to range between 1.94 × 10−10 and 8.49 × 10−10 m2/s over the temperature range studied. The values of activation energy were calculated as 36.82 and 37.12 kJ/mol for control and pretreated samples, respectively. Superior rehydration was noticed for citric acid pretreated slices dried at 65°C.

Drying Characteristics of Soybean (Glycine Max) Using Continuous Drying and Intermittent Drying

2018 ◽  
Vol 14 (9-10) ◽  
Author(s):  
Hyeon W. Park ◽  
Won Y. Han ◽  
Won B. Yoon
Keyword(s):  
Activation Energy ◽  
Moisture Content ◽  
Analysis Method ◽  
Image Analysis Method ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying ◽  
Drying Models ◽  
Thin Layer Drying Models ◽  
Best Fit

AbstractThe effects of drying temperature by continuous and intermittent drying on the drying characteristics of soybean were determined in this study. Among the thin-layer drying models, the Midilli–Kucuk model showed the best fit (R2> 0.99) to describe the drying of soybean. At 300 min of the effective drying time, the moisture content of continuous drying at 35, 40, and 45 ºC were 9.38 (±0.00), 8.69 (±0.17), and 7.70 % (±0.48), respectively; while the moisture content of intermittent drying at 35, 40, and 45 ºC were 8.28 (±0.21), 7.31 (±0.41), and 6.97 % (±0.07), respectively. The image analysis method for detection of the crack in soybean demonstrated that at the target moisture content (7.7 %), cracked grain ratios with intermittent drying at 35, 40, and 45 ºC were reduced by 52.08, 27.59, and 18.24 %, respectively. With the effective drying time, the activation energy for intermittent drying (9.33 kJ/mol) was significantly lower than that value for continuous drying (21.23 kJ/mol).

scholarly journals Drying Modelling, Moisture Diffusivity and Sensory quality of Thin Layer dried Beef

2018 ◽  
Vol 6 (2) ◽  
pp. 552-565 ◽  
Author(s):  
Eunice Akello Mewa ◽  
Michael Wandayi Okoth ◽  
Catherine Nkirote Kunyanga ◽  
Musa Njue Rugiri
Keyword(s):  
Thin Layer ◽  
Sensory Quality ◽  
Moisture Diffusivity ◽  
Drying Kinetics ◽  
Effect Of Temperature ◽  
Slice Thickness ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying

The objective of the present study was to determine the drying kinetics, moisture diffusivity and sensory quality of convective air dried beef. The effect of temperature of drying (30-60°C) and thickness of samples (2.5-10 mm) on the convective thin-layer drying kinetics of beefdried in a cabinet dryer was evaluated. Five semi-theoretical models were fit to the drying experimentaldata with the aim of predicting drying characteristics of beef and fitting quality of models determined using the standard error of estimate (SEE)and coefficient of determination (R2). Determination ofeffective moisture diffusivity (Deff) from the experimental drying datawas done and sensory quality of the optimized dried cooked and uncookedbeef samplesevaluated. Drying time and rate of drying increased with an increasing temperature but decreased with increased slice thickness. However, there was overlapping of drying curves at 40-50°C. Among the selected models, Page model gave the best prediction of beef drying characteristics. Effective moisture diffusivity (Deff) ranged between 4.2337 x 10-11 and 5.5899 x 10-10 m2/s, increasing with an increase in air temperature and beef slice thickness.Of all the sensory parameters evaluated, texture was the only attribute that gave significantly different (P > 0.05) scores between the cooked and uncooked dried beef samples.

The thin-layer drying characteristics of sewage sludge by the appropriate foaming pretreatment

2014 ◽  
Vol 69 (9) ◽  
pp. 1859-1866 ◽  
Author(s):  
Hui-Ling Wang ◽  
Zhao-Hui Yang ◽  
Jing Huang ◽  
Li-Ke Wang ◽  
Cheng-Liu Gou ◽  
...  
Keyword(s):  
Sample Thickness ◽  
Coefficient Of Determination ◽  
Drying Rate ◽  
Drying Time ◽  
Drying Characteristics ◽  
Thin Layer Drying ◽  
Dewatered Sludge ◽  
Drying Curves ◽  
Sludge Drying ◽  
The Impact

As dewatered sludge is highly viscous and sticky, the combination of foaming pretreatment and drying process seems to be an alternative method to improve the drying performance of dewatered sludge. In this study, CaO addition followed by mechanical whipping was employed for foaming the dewatered sludge. It was found that the foams were stable and the diameters of bubbles mainly ranged from 0.1 to 0.3 mm. The drying experiments were carried out in a drying oven in the convective mode. The results indicated that foamed sludge at 0.70 g/cm3 had the best drying performance at each level of temperature, which could save 35–45% drying time to reach 20% moisture content compared with the non-foamed sludge. The drying rate of foamed sludge at 0.70 g/cm3 was improved with the increasing of drying temperature. The impact of sample thickness on drying rate was not obvious when the sample thickness increased from 2 to 8 mm. Different mathematical models were used for the simulation of foamed sludge drying curves. The Wang and Singh model represented the drying characteristics better than other models with coefficient of determination values over 0.99.

Mathematical Modelling of Thin Layer Sun and Solar Drying of Cassava Chips

2010 ◽  
Vol 6 (6) ◽  
Author(s):  
Toyosi Y Tunde-Akintunde
Keyword(s):  
Thin Layer ◽  
Correlation Coefficients ◽  
Moisture Diffusivity ◽  
Solar Drying ◽  
Drying Time ◽  
Drying Characteristics ◽  
Page Model ◽  
Thin Layer Drying ◽  
Rate Period ◽  
Pretreatment Conditions

In this paper, the effect of sun and solar drying and pretreatment conditions (soaking in water; soaking in water and then blanching; blanching and then soaking) on the drying characteristics and kinetics of cassava chips were investigated. The drying time was shorter for samples pretreated by soaking only (SK) compared to the others. It was observed that pretreatment conditions and drying method significantly (P < 0.05) affected the drying rate. The drying for all experiments occurred in the falling rate period with no constant rate period. Four mathematical models were studied for the description thin layer drying characteristics of pretreated cassava chips. The models considered were the Henderson and Pabis, Newton, Logarithmic and the Page model. Comparing the correlation coefficients (R2), chi-square (c2) and root mean square error (RMSE) values of four models, it was observed that the highest values of R2 and lowest ?2 and RMSE were obtained using Page model. This shows that the Page model represents drying characteristics better than other models. The effective moisture diffusivity values were estimated from Fick’s diffusional model. These values obtained for solar dried samples were generally higher than those obtained for sun dried samples.

scholarly journals The Experimental Research of Drying Kinetics of Nagpur Orange Fruit (Citrus Sinesis- L) by Hot Air Electrical Dryer

2019 ◽  
Vol 8 (6S4) ◽  
pp. 1131-1134
Keyword(s):  
Thin Layer ◽  
Drying Kinetics ◽  
Drying Time ◽  
Drying Characteristics ◽  
Drying Temperature ◽  
Hot Air ◽  
Thin Layer Drying ◽  
Drying Behavior ◽  
Orange Fruit ◽  
Kinetics Of

The study is aimed experimentally and compared with the theoretical results of drying kinetics of Nagpur orange fruit dried in a hot air electrical dryer. Orange fruit is highly perishable and needs to be consumed or processed immediately after harvest. Drying or dehydration is one of the most practical methods of preserving food products. Therefore, thin layer drying characteristics of falling rate of Nagpur orange are determined experimentally under different conditions of drying air temperatures, relative humidity and air velocities for different moisture contents. Thin layer models like Wang and Singh, Page and Henderson have been compared with Experimental results. The knowledge of drying kinetics helps for identification of exact drying time and air flow velocity for different moisture content. Here drying operation is carried out at a velocity of 1m/sec and 1.25 m/sec for different temperature of 55°C, 65°C and 75°C. This analysis reveals that drying temperature has a more significant effect on moisture removal while velocity has the least effect. Drying rate is found to increase with the increase in drying temperature and reduce with drying time. Experimental data is statistically correlated by plotting the drying characteristics curve. The analysis reveals that Wang and Singh's model is a better model to explain the drying behavior of Nagpur Orange fruit (R2=0.9888).

scholarly journals Drying Kinetics of Sliced Pineapples in a Solar Conduction Dryer

2017 ◽  
Vol 7 (2) ◽  
pp. 14 ◽  
Author(s):  
Luqman Ebow Ibn Daud ◽  
Isaac Nyambe Simate
Keyword(s):  
Thin Layer ◽  
Average Moisture Content ◽  
Drying Time ◽  
Sun Drying ◽  
Thin Layer Drying ◽  
Drying Models ◽  
Drying Model ◽  
Thin Layer Drying Models ◽  
Drying Curves ◽  
Kinetics Of

As a means of adding value to pineapple production and minimising post-harvest losses, sliced pineapples were dried using a Solar Conduction Dryer (SCD) and appropriate thin layer drying models to predict drying were developed whilst the performance of the SCD was also investigated. For the period of the experiment, ambient temperature and temperature in the dryer ranged from 24 to 37 °C and 25 to 46 ℃ respectively. The performance of the dryer was compared to open sun drying using pineapple slices of 3-5 mm in thickness where the slices were reduced from an average moisture content of 85.42 % (w.b.) to 12.23 % (w.b.) by the SCD and to 51.51 % (w.b.) by the open sun drying in 8 hours effective drying time. Pineapple slices of thicknesses 3 mm, 5 mm, 7 mm and 10 mm were simultaneously dried in the four drying chambers of the SCD and their drying curves simulated with twelve thin layer drying models. The Middilli model was found as the best fitted thin layer drying model for sliced pineapples. The optimum fraction of drying tray area that should be loaded with pineapples was also investigated by simultaneously loading 7 mm slices of pineapples at 50, 75, and 100 percent of drying tray area. Loading the slices at 50, 75 and 100 percent of drying tray area gave overall thermal efficiencies of 23, 32 and 44 percent, respectively, hence loading pineapple slices at 100 percent drying tray area was recommended as the best.

scholarly journals Modelling the Drying Characteristics and Kinetics of Hot Air-Drying of Unblanched Whole Red Pepper and Blanched Bitter Leaf Slices

2017 ◽  
Vol 5 (1) ◽  
pp. 24
Author(s):  
Samuel Enahoro Agarry
Keyword(s):  
Moisture Diffusivity ◽  
Effective Moisture Diffusivity ◽  
Red Pepper ◽  
Coefficient Of Determination ◽  
Drying Time ◽  
Drying Characteristics ◽  
Hot Air ◽  
Effective Moisture ◽  
Drying Curves ◽  
Kinetics Of

The objective of this study was to investigate the drying characteristics and kinetics of red pepper and bitter leaf under the influence of different drying temperatures. The drying experiments were carried out at dry bulb temperature of 35, 45, 55 and 75oC, respectively in an oven dryer. The results showed that as drying temperature increased, drying rate also increased and the drying time decreased. It was observed that un-sliced red pepper and sliced bitter leaf would dry within 2.5-12 h and 1.67-7 h, respectively at temperature ranging from 75 to 35oC. The drying of red pepper and bitter leaf was both in the constant and falling rate period. Four semi-empirical mathematical drying models (Newton, Page, Henderson and Pabis, and Logarithmic models) were fitted to the experimental drying curves. The models were compared using the coefficient of determination (R^2) and the root mean square error (RMSE). The Page model has shown a better fit to the experimental drying data of red pepper and bitter leaf, respectively as relatively compared to other tested models. Moisture transport during drying was described by the application of Fick’s diffusion model and the effective moisture diffusivity was estimated. The value ranges from 15.69 to 84.79 × 10-9 m2/s and 0.294 to 1.263 × 10-9 m2/s for red pepper and bitter leaf, respectively. The Arrhenius-type relationship describes the temperature dependence of effective moisture diffusivity and was determined to be 37.11 kJ/mol and 32.86 kJ/mol for red pepper and bitter leaf, respectively. A correlation between the drying time and the heat transfer area was also developed.

scholarly journals Infrared drying kinetics of blue mussels and physical properties

2019 ◽  
Vol 25 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Azmi Kipcak ◽  
İbrahim Doymaz ◽  
Emek Moroydor-Derun
Keyword(s):  
Blue Mussel ◽  
Power Level ◽  
Colour Change ◽  
Moisture Diffusivity ◽  
Drying Kinetics ◽  
Drying Time ◽  
Blue Mussels ◽  
Thin Layer Drying ◽  
Drying Models ◽  
Kinetics Of

As an alternative to fish and beef, blue mussels (Mytilus edulis) can be consumed due to their high protein content. In this study, the drying kinetics and quality changes (cook loss, area shrinkage and colour change) in whole blue mussels were investigated with several infrared power levels between 88?146 W. Various thin-layer drying models were applied to the blue mussel and the Midilli et al., model best fits the experimental data (R2: 0.999150?0.999750, ?2: 0.000104?0.000030, RMSE: 0.008309?0.004797). The effective moisture diffusivity was determined to be between 4.24?10-9 and 1.10?10-8 m2/s. The activation energy was found to be 20.85 kW/kg. The cook loss and area shrinkage increased with increasing power level and drying time. Most cook loss (30%) and area shrinkage (30%) were obtained between 15-23 min and 8-20 min of drying time, respectively. The colour change was slightly affected by the change in infrared power level.

Sign in / Sign up

Export Citation Format

Share Document