Vulcanization of Elastomers. 12. Perbunan with Thiuram Monosulfide and Sulfur. I

1959 ◽  
Vol 32 (1) ◽  
pp. 128-138 ◽  
Author(s):  
Walter Scheele ◽  
Horst-Eckart Toussaint

Abstract The vulcanization of Perbunan 2818 by tetramethylthiuram monsulfide plus sulfur (1 mole monosulfide per gram-atom S) was thoroughly studied. The following results were shown: The limiting value for dithiocarbamate formation is 66 mole per cent of the initial thiuram monosulfide, indicating a two-thirds transformation. The limiting value is practically independent of temperature. The formation of dithiocarbamate can be described as a reaction of the first order. The formation of dithiocarbamate is characterized by an induction period which grows longer with lowering of the temperature, and at 100° C it amounts to about 100 minutes. The rate constants for dithiocarbamate formation were calculated, and it was shown that they were practically the same as those for the vulcanization of Perbunan with tetramethylthiuram disulfide. The activation energies as derived from the temperature dependence of the rate constants for dithiocarbamate formation in the vulcanization of Perbunan by thiuram monosulfide plus sulfur on the one hand and with thiuram disulfide on the other, are only very slightly different and are practically the same as the activation energy for dithiocarbamate formation during the vulcanization of natural rubber with thiuram monosulfide plus sulfur. The results were thoroughly discussed in light of the present conceptions of the course of thiuram vulcanizations.

1959 ◽  
Vol 32 (2) ◽  
pp. 566-576
Author(s):  
Walter Scheele ◽  
Klaus Hummel

Abstract Bound sulfur in a pure thiuram vulcanizate increases relatively rapidly at first at all temperatures, reaches a poorly defined maximum at about 27 to 30%, independent of temperature, and then recedes slightly to reach a limiting value of 25% also independent of temperature, based on the original thiuram disulfide. The rise in sulfur content at the start points to a temperature-independent limiting value of 33%. It is shown that the combination of sulfur in this region initially follows a first order reaction, and goes at the same rate as the reduction in concentration of thiuram disulfide. It can be seen from the above that sulfur may be combined in thiuram vulcanization without simultaneous crosslinking. The dithiocarbamate formation increases rapidly in the region of longer vulcanization times, after the maximum in bound sulfur has been reached, without further combination of sulfur with the vulcanizate. The rate constants for thiuram decrease, for dithiocarbamate increase and for sulfur combination were calculated. The temperature dependence of each of these reactions has practically the same activation energy, 23 kcal/mole. The bound sulfur content of the vulcanizates in pure thiuram vulcanizations is no criterion of the state of vulcanization.


1956 ◽  
Vol 29 (1) ◽  
pp. 37-48 ◽  
Author(s):  
Walter Scheele ◽  
Otto Lorenz

Abstract If we disregard for the moment the phenomena which occur in the interaction of thiuram disulfide with geraniol under the influence of air and confine our consideration to the results which can be deduced from the study of this reaction in a stream of nitrogen, we are led to the conclusion that geraniol, which was used as a model compound, behaves with respect to its interaction with tetraethylthiuram disulfide, not only qualitatively but also quantitatively, exactly like rubber, and that it is not to be assumed that other tetraalkylthiuram disulfides as well as other compounds which are analogous to geraniol will behave differently. Thus the results can be evaluated as a proof that the vulcanization of natural rubber by thiuram disulfides depends on nothing other than a definite and always similar interaction with the allyl groups of the polyisoprene chain. The results of the investigation described in this paper can be regarded, moreover, as support for the correctness of our procedure in the clarification of the vulcanization mechanisms, and they stress the importance of analytical-chemical methods, which have certainly not been pursued in the past with the necessary intensity and insight. These investigations are being continued. It has already been found that the vulcanization of natural rubber with thiuram monosulfides and sulfur leads to the same results as vulcanization with thiuram disulfides. This has been conjectured, to be sure, by a number of workers. However, it was never really demonstrated experimentally. We shall report on this in the near future. The experimental results can now be summarized as follows : 1. The reaction between thiuram disulfide and geraniol (demonstrated by the example of tetraethylthiuram disulfide) takes place qualitatively and quantitatively like the interaction between thiuram disulfide and natural rubber. In the vulcanization of rubber by thiuram disulfides, therefore, there is involved a reaction of the thiuram disulfide with the allyl groups, leading to a definite conversion. 2. It was found that in the interaction of geraniol with thiuram disulfide under nitrogen and in the presence of zinc oxide, the limiting value of zinc dithiocarbamate amounts to 66 mole-per cent of the original thiuram disulfide, independent of the temperature. This was the result found in the study of the reaction of the thiuram disulfides with rubber. 3. We were able to show that the limiting value of the dithiocarbamate yield in the interaction of tetraethylthiuram disulfide with geraniol is independent of the thiuram disulfide concentration. This is likewise true for the reaction of the thiuram disulfides with natural rubber. From this it follows that the interaction of thiuram disulfides with allyl groupings, as they occur in the polyisoprene chain, is apparently a stoichiometric one. For this reason we can no longer retain the assumption that the limiting value of the yield of dithiocarbamate is the result of a sterically hindered reaction. 4. The change of concentration of zinc dithiocarbamate in the interaction of tetraethylthiuram disulfide with geraniol under nitrogen can be accounted for by postulating a reaction of the first order. The velocity constants were calculated and it was found that the resulting activation energy is somewhat greater than the one for the interaction with natural rubber. 5. Similarly the concentration of thiuram disulfide obeys a first-order reaction as it falls off to zero. The velocity constants were calculated. The activation energy obtained from the temperature dependence is in good agreement with that found for the interaction with rubber. 6. In the presence of oxygen, the reaction between thiuram disulfide and geraniol takes a quite different course. The rate of decrease of concentration of thiuram disulfide, which likewise follows a first-order reaction, is higher. The yield of zinc dithiocarbamate does not attain the constant value of 66 mole-per cent of the original thiuram disulfide. In the temperature range studied, the amount of dithiocarbamate found is smaller. The limiting value reached at the various temperatures is progressively smaller, the lower the temperature chosen. Whether by expanding the temperature range, one would eventually reach a minimum and a maximum limiting value has not been investigated.


1957 ◽  
Vol 30 (3) ◽  
pp. 911-927 ◽  
Author(s):  
Otto Lorenz ◽  
Elisabeth Echte

Abstract 1. The decrease of free sulfur occurs according to the first order law during the vulcanization of natural rubber accelerated by mercaptobenzothiazole in the presence of zinc oxide. The activating energy for this reaction amounts to 30.5 kcal./mole. 2. If zinc benzothiazolylmercaptide is used as an accelerator, one obtains the same rate constants for the sulfur decrease as in the presence of mercaptobenzothiazole. These seem to be equivalent as regards their effectiveness of acceleration. 3. A kinetic analysis of the reciprocal swelling, which represents a measure of network formation, indicates that the reaction is first order. Sulfur decrease and reciprocal swelling prove to be equal processes as regards rate. This is true where vulcanization is accelerated with mercaptobenzothiazole or with the zinc salt. 4. During vulcanization there occurs a decrease of accelerator concentration. This is dependent upon the temperature and is tied in with the combination sulfur with rubber. 5. If the quantity of the accelerator added is changed, the rate constants for sulfur decrease and for reciprocal swelling do not change, provided that a minimum quantity of accelerator is present. 6. In vulcanization accelerated with zinc benzothiazolylmercaptide, zinc oxide being absent, sulfur decrease again occurs according to the first order law but considerably faster, without thereby changing the activation energy. These investigations are being continued and the results will be discussed in detail in relation to other published contributions in this field.


2012 ◽  
Vol 535-537 ◽  
pp. 1214-1217
Author(s):  
Yong Zhou Wang ◽  
Hong Xing Gui ◽  
Tao Chen ◽  
Hong Hai Huang ◽  
Fu Quan Zhang ◽  
...  

In this work, effect of carboxymethyl chitosan (CMCS) on vulcanization kinetics of natural rubber was studied using the Rheometer MDR2000.The results showed that both the rate constants of induction period and curing period of natural rubber (K-N) was greater than that of natural rubber added CMCS and the dosage is 0.05% of fresh latex (CMCS-1), but less than that of natural rubber added CMCS and the dosage is 0.1% of fresh latex (CMCS-2), and the activation energy 100.8kJ/mol of induction period of K-N is greater than the activation energy 96.7kJ/mol, 93.7kJ/mol of induction period of CMCS-1, CMCS-2, respectively and that the activation energy 104.4 kJ/mol of curing period of K-N is less than the activation energy111.9kJ/mol of curing period of CMCS-1, and bigger than the activation energy 103.4 of CMCS-2 at the same temperature.


2010 ◽  
Vol 160-162 ◽  
pp. 1181-1186 ◽  
Author(s):  
Zhi Feng Wang ◽  
Si Dong Li ◽  
Xiao Dong She

Kinetics of vulcanization of natural rubber coagulated by microorganisms (NR-m) was studied with the use of a vulcameter. In the induction period of vulcanization, the time t0 of NR-m is shorter than that of natural rubber coagulated by acid (NR-a), and the rate constant k1/a of NR-m are greater than that of NR-a. Both the curing periods of NR-m and NR-a consist of two stages. The first stage follows first-order reaction. The rate constants k2 of NR-m in the first stage are greater than that of NR-a at the same temperature, and so are the activation energy E2. The second stage (end stage of the curing period) does not follow first-order reaction, and the calculated reaction order n of NR-m is in the range of 0.82-0.85, and that of NR-a is in the range of 0.64-0.72. The rate constants k3 of the second stage for NR -m are greater than that of NR-a at the same temperature, and so is the activation energy E3.


1956 ◽  
Vol 29 (1) ◽  
pp. 15-28 ◽  
Author(s):  
Walter Scheele ◽  
Otto Lorenz ◽  
Wilhelm Dummer

Abstract This paper gives some insight into the kinetics of thiuram vulcanization. The following results were obtained. 1. The decrease of concentration of thiuram disulfides during vulcanization is a first-order reaction in the range of short vulcanization times. At longer reaction times, departures occur. The process then takes place more slowly. 2. The departures from the course of a first-order reaction are displaced with decreasing temperature toward the range of longer vulcanization times. 3. At 87° C, the reaction of tetramethylthiuram disulfide is of the first order over the whole range of vulcanization temperatures chosen, and at this temperature no deviations whatever are observed. 4. The same relationships are found in the kinetic study of dithiocarbamate formation. 5. From the combined results, it is concluded that, besides the two reactions occurring independently of each other during vulcanization, the diffusion of the reaction partners also has some influence on the kinetics. 6. The limiting value of dithiocarbamate formation is correlated with the macromolecular structure of the polyisoprene, and it is shown to be probable that this limit is not determined fundamentally by the chemistry of the vulcanization reaction.


1981 ◽  
Vol 27 (5) ◽  
pp. 753-755 ◽  
Author(s):  
P A Adams ◽  
M C Berman

Abstract We describe a simple, highly reproducible kinetic technique for precisely measuring temperature in spectrophotometric systems having reaction cells that are inaccessible to conventional temperature probes. The method is based on the temperature dependence of pseudo-first-order rate constants for the acid-catalyzed hydrolysis of N-o-tolyl-D-glucosylamine. Temperatures of reaction cuvette contents are measured with a precision of +/- 0.05 degrees C (1 SD).


1960 ◽  
Vol 33 (2) ◽  
pp. 335-341
Author(s):  
Walter Scheele ◽  
Karl-Heinz Hillmer

Abstract As a complement to earlier investigations, and in order to examine more closely the connection between the chemical kinetics and the changes with vulcanization time of the physical properties in the case of vulcanization reactions, we used thiuram vulcanizations as an example, and concerned ourselves with the dependence of stress values (moduli) at different degrees of elongation and different vulcanization temperatures. We found: 1. Stress values attain a limiting value, dependent on the degree of elongation, but independent of the vulcanization temperature at constant elongation. 2. The rise in stress values with the vulcanization time is characterized by an initial delay, which, however, is practically nonexistent at higher temperatures. 3. The kinetics of the increase in stress values with vulcanization time are both qualitatively and quantitatively in accord with the dependence of the reciprocal equilibrium swelling on the vulcanization time; both processes, after a retardation, go according to the first order law and at the same rate. 4. From the temperature dependence of the rate constants of reciprocal equilibrium swelling, as well as of the increase in stress, an activation energy of 22 kcal/mole can be calculated, in good agreement with the activation energy of dithiocarbamate formation in thiuram vulcanizations.


2010 ◽  
Vol 8 (2) ◽  
pp. 219-225
Author(s):  
Yoeswono Yoeswono ◽  
Triyono Triyono ◽  
Iqmal Tahir

A study on palm oil transesterification to evaluate the effect of some parameters in the reaction on the reaction kinetics has been carried out. Transesterification was started by preparing potassium methoxide from potassium hydroxide and methanol and then mixed it with the palm oil. An aliquot was taken at certain time interval during transesterification and poured into test tube filled with distilled water to stop the reaction immediately. The oil phase that separated from the glycerol phase by centrifugation was analyzed by 1H-NMR spectrometer to determine the percentage of methyl ester conversion. Temperature and catalyst concentration were varied in order to determine the reaction rate constants, activation energies, pre-exponential factors, and effective collisions. The results showed that palm oil transesterification in methanol with 0.5 and 1 % w/w KOH/palm oil catalyst concentration appeared to follow pseudo-first order reaction. The rate constants increase with temperature. After 13 min of reaction, More methyl esters were formed using KOH 1 % than using 0.5 % w/w KOH/palm oil catalyst concentration. The activation energy (Ea) and pre-exponential factor (A) for reaction using 1 % w/w KOH was lower than those using 0.5 % w/w KOH.   Keywords: palm oil, transesterification, catalyst, first order kinetics, activation energy, pre-exponential factor


1971 ◽  
Vol 26 (10) ◽  
pp. 1010-1016 ◽  
Author(s):  
Renate Voigt ◽  
Helmut Wenck ◽  
Friedhelm Schneider

First order rate constants of the reaction of a series of SH-, imidazole- and imidazole/SH-compounds with FDNB as well as their pH- and temperature dependence were determined. Some of the tested imidazole/SH-compounds exhibit a higher nucleophilic reactivity as is expected on the basis of their pKSH-values. This enhanced reactivity is caused by an activation of the SH-groups by a neighbouring imidazole residue. The pH-independent rate constants were calculated using the Lindley equation.The kinetics of DNP-transfer from DNP-imidazole to SH-compounds were investigated. The pH-dependence of the reaction displays a maximum curve. Donor in this reaction is the DNP-imidazolecation and acceptor the thiolate anion.The reaction rate of FDNB with imidazole derivatives is two to three orders of magnitude slower than with SH-compounds.No inter- or intra-molecular transfer of the DNP-residue from sulfure to imidazole takes place.


Sign in / Sign up

Export Citation Format

Share Document