The Vulcanization of Elastomers. XI. The Vulcanization of Natural Rubber with Sulfur in the Presence of Mercaptobenzothiazole. I

1957 ◽  
Vol 30 (3) ◽  
pp. 911-927 ◽  
Author(s):  
Otto Lorenz ◽  
Elisabeth Echte
Keyword(s):  
Activation Energy ◽  
Zinc Oxide ◽  
Natural Rubber ◽  
Kinetic Analysis ◽  
Rate Constants ◽  
Network Formation ◽  
Zinc Salt ◽  
Kcal Mole ◽  
Minimum Quantity ◽  
First Order

Abstract 1. The decrease of free sulfur occurs according to the first order law during the vulcanization of natural rubber accelerated by mercaptobenzothiazole in the presence of zinc oxide. The activating energy for this reaction amounts to 30.5 kcal./mole. 2. If zinc benzothiazolylmercaptide is used as an accelerator, one obtains the same rate constants for the sulfur decrease as in the presence of mercaptobenzothiazole. These seem to be equivalent as regards their effectiveness of acceleration. 3. A kinetic analysis of the reciprocal swelling, which represents a measure of network formation, indicates that the reaction is first order. Sulfur decrease and reciprocal swelling prove to be equal processes as regards rate. This is true where vulcanization is accelerated with mercaptobenzothiazole or with the zinc salt. 4. During vulcanization there occurs a decrease of accelerator concentration. This is dependent upon the temperature and is tied in with the combination sulfur with rubber. 5. If the quantity of the accelerator added is changed, the rate constants for sulfur decrease and for reciprocal swelling do not change, provided that a minimum quantity of accelerator is present. 6. In vulcanization accelerated with zinc benzothiazolylmercaptide, zinc oxide being absent, sulfur decrease again occurs according to the first order law but considerably faster, without thereby changing the activation energy. These investigations are being continued and the results will be discussed in detail in relation to other published contributions in this field.

Vulcanization of Elastomers. 21. Vulcanization of Natural Rubber with Thiuram Disulfides. VI

1959 ◽  
Vol 32 (2) ◽  
pp. 566-576
Author(s):  
Walter Scheele ◽  
Klaus Hummel
Keyword(s):  
Activation Energy ◽  
Natural Rubber ◽  
Temperature Dependence ◽  
Sulfur Content ◽  
Rate Constants ◽  
Order Reaction ◽  
First Order Reaction ◽  
Kcal Mole ◽  
First Order ◽  
Limiting Value

Abstract Bound sulfur in a pure thiuram vulcanizate increases relatively rapidly at first at all temperatures, reaches a poorly defined maximum at about 27 to 30%, independent of temperature, and then recedes slightly to reach a limiting value of 25% also independent of temperature, based on the original thiuram disulfide. The rise in sulfur content at the start points to a temperature-independent limiting value of 33%. It is shown that the combination of sulfur in this region initially follows a first order reaction, and goes at the same rate as the reduction in concentration of thiuram disulfide. It can be seen from the above that sulfur may be combined in thiuram vulcanization without simultaneous crosslinking. The dithiocarbamate formation increases rapidly in the region of longer vulcanization times, after the maximum in bound sulfur has been reached, without further combination of sulfur with the vulcanizate. The rate constants for thiuram decrease, for dithiocarbamate increase and for sulfur combination were calculated. The temperature dependence of each of these reactions has practically the same activation energy, 23 kcal/mole. The bound sulfur content of the vulcanizates in pure thiuram vulcanizations is no criterion of the state of vulcanization.

Vulcanization of Elastomers. 40. Vulcanization of Natural Rubber and Synthetic Rubber with Sulfur in Presence of Sulfenamides. III

1965 ◽  
Vol 38 (1) ◽  
pp. 189-203 ◽  
Author(s):  
W. Scheele ◽  
J. Helberg
Keyword(s):  
Activation Energy ◽  
Reaction Mechanism ◽  
Natural Rubber ◽  
Rate Constants ◽  
Sulfur Concentration ◽  
Kcal Mole ◽  
Synthetic Rubber ◽  
Chemical Constitution ◽  
Induction Times ◽  
Kinetics Of

Abstract Vulcanization of natural rubber with sulfur was studied in presence of six sulfenamides, to determine the effect of the chemical constitution of the sulfenamide on sulfur decrease and on crosslinking. The results can be condensed as follows: (1) The kinetics of sulfur disappearance is in every respect qualitatively independent of the chemical constitution of the sulfenamide. (2) For the sulfenamides investigated, the smallest and largest rate constants for sulfur decrease differed only by a factor of two. (3) Greater differences are encountered in the induction times for sulfur decrease and for crosslinking. The latter are notably longer than those for sulfur disappearance. (4) The same activation energy, 23 kcal/mole, is derived from the temperature dependence of the induction times for all the sulfenamides. (5) The dissociation of sulfenamides in solution and their reaction with mercaptobenzothiazole were investigated further. The results provide the basis for a proposed reaction mechanism, which is presented in detail and can account for a number of the features typical of sulfenamide-accelerated vulcanization. (6) The drop in sulfur concentration goes at practically the same rate, if one introduces, instead of N, N-dicyclohexyl-2-benzothiazolesulfenamide, the corresponding ammonium mercaptide in equimolar concentration.

THE THERMAL DECOMPOSITION OF METHYL HYDROPEROXIDE

1965 ◽  
Vol 43 (8) ◽  
pp. 2236-2242 ◽  
Author(s):  
Alexander D. Kirk
Keyword(s):  
Activation Energy ◽  
Thermal Decomposition ◽  
Gas Phase ◽  
Rate Constants ◽  
Dimethyl Phthalate ◽  
Kcal Mole ◽  
First Order ◽  
Methyl Hydroperoxide ◽  
Expected Values ◽  
Homogeneous Decomposition

The thermal decomposition of methyl hydroperoxide has been studied in solution and in the gas phase. The decomposition was found to be partly heterogeneous in solution in dimethyl phthalate and no reliable rate constants were obtained. Use of the toluene carrier method for the gas phase work enabled measurement of the rate constant for the homogeneous decomposition. The first order rate constants obtained range from 0.19 s−1 at 292 °C to 1.5 s−1 at 378 °C, leading to log A, 11± 2, and activation energy, 32 ± 5 kcal/mole. These results are compared with the expected values of log A, 13–14, and activation energy, 42 kcal/mole. The significance of these findings is discussed.

THE PYROLYSIS OF TOLUENE

1962 ◽  
Vol 40 (7) ◽  
pp. 1310-1317 ◽  
Author(s):  
S. J. Price
Keyword(s):  
Activation Energy ◽  
Rate Constant ◽  
Rate Constants ◽  
Contact Time ◽  
Flow System ◽  
Kcal Mole ◽  
Homogeneous Process ◽  
First Order ◽  
Order Rate ◽  
Toluene Concentration

The pyrolysis of toluene has been studied in a flow system from 913 to 1143 °K. First-order rate constants are independent of the toluene concentration but decrease approximately 9% when the contact time is reduced from 1.0 to 0.41 second. Increasing the contact time from 1.0 second to 2.07 seconds does not affect the rate constant. The overall rate has been resolved into homogeneous and heterogeneous components. It is suggested that the activation energy of the homogeneous process, 85 kcal/mole, may be associated with D(C6H5CH2—H).

Vulcanization of Elastomers. 12. Perbunan with Thiuram Monosulfide and Sulfur. I

1959 ◽  
Vol 32 (1) ◽  
pp. 128-138 ◽  
Author(s):  
Walter Scheele ◽  
Horst-Eckart Toussaint
Keyword(s):  
Activation Energy ◽  
Natural Rubber ◽  
Temperature Dependence ◽  
Induction Period ◽  
Rate Constants ◽  
The Other ◽  
Tetramethylthiuram Disulfide ◽  
First Order ◽  
The One ◽  
Limiting Value

Abstract The vulcanization of Perbunan 2818 by tetramethylthiuram monsulfide plus sulfur (1 mole monosulfide per gram-atom S) was thoroughly studied. The following results were shown: The limiting value for dithiocarbamate formation is 66 mole per cent of the initial thiuram monosulfide, indicating a two-thirds transformation. The limiting value is practically independent of temperature. The formation of dithiocarbamate can be described as a reaction of the first order. The formation of dithiocarbamate is characterized by an induction period which grows longer with lowering of the temperature, and at 100° C it amounts to about 100 minutes. The rate constants for dithiocarbamate formation were calculated, and it was shown that they were practically the same as those for the vulcanization of Perbunan with tetramethylthiuram disulfide. The activation energies as derived from the temperature dependence of the rate constants for dithiocarbamate formation in the vulcanization of Perbunan by thiuram monosulfide plus sulfur on the one hand and with thiuram disulfide on the other, are only very slightly different and are practically the same as the activation energy for dithiocarbamate formation during the vulcanization of natural rubber with thiuram monosulfide plus sulfur. The results were thoroughly discussed in light of the present conceptions of the course of thiuram vulcanizations.

The Vulcanization of Elastomers. 13. The Vulcanization of Natural Rubber with Sulfur in the Presence of Mercaptobenzothiazole. II

1958 ◽  
Vol 31 (1) ◽  
pp. 117-131 ◽  
Author(s):  
O. Lorenz ◽  
Elisabeth Echte
Keyword(s):  
Natural Rubber ◽  
Rate Constants ◽  
Zinc Stearate ◽  
Molar Ratio ◽  
Crosslinking Reaction ◽  
Square Root ◽  
Kcal Mole ◽  
First Order ◽  
Equilibrium Swelling ◽  
Rate Processes

Abstract The vulcanization of natural rubber with sulfur, using mercaptobenzothiazole as accelerator in the presence of zinc stearate, was investigated. The results were as follows: 1) When natural rubber is cured with sulfur in the presence of zinc oxide and mercaptobenzothiazole, as well as zinc stearate, one observes, with the first order diminution of sulfur concentration, an induction period that grows longer as the cure temperature falls. 2) For the disappearance of sulfur there is calculated, from the temperature dependence of the rate constants, an activation energy of 19.5 kcal/mole. This value is considerably smaller than that found for the mercaptobenzothiazole-accelerated sulfur cure when no zinc stearate is present. 3) The percentage loss in mercaptobenzothiazole during vulcanization is, in the presence of zinc stearate, independent of the temperature; there is a reaction, independent of the amount of stearate added of 5 molecules of S8 for each molecule of mercaptobenzothiazole. 4) The diminution in accelerator can also be explained as a first order reaction, and it becomes evident that disappearance of accelerator and sulfur are equivalent-rate processes. 5) The crosslinking, measured by the reciprocal equilibrium swelling, goes according to the first order, yet sulfur disappearance and the crosslinking reaction are not equal rate processes, which was always true in the absence of zinc stearate. In each case the crosslinking rate constants are greater than those for the decrease in sulfur. 6) For the activation energy of network formation, we calculated, from the temperature dependence of the rate constants of the reciprocal equilibrium swelling, 20.5 kcal/mole. 7) When the stearate content is constant, there is a linear relationship between kSI, the rate constant for sulfur diminution, and the given amount of mercaptobenzothiazole, up to an initial molar ratio of mercaptobenzothiazole: stearate = 4:1. Increases in accelerator proportion beyond this initial ratio cause no further rise in the rate constants. 8) The rate constants of the crosslinking reaction also increase with increasing proportion of mercaptobenzothiazole (stearate portion remaining constant), until the initial molar ratio of mercaptobenzothiazole:zinc stearate = 4:1 is reached. Nevertheless, the relationship is not linear. 9) There is a linear relationship between the amount of zinc stearate in the vulcanizate and the maximum sulfur-loss rate constants kSI (max). 10) The maximum rate constants of the network forming reaction kQI (max) are proportional to the square root of the stearate content. 11) The number of crosslinkage points formed is independent of the quantity of mercaptobenzothiazole, when the stearate content is constant. 12) The number of crosslinking points formed increases, however, along with increasing stearate content, and is proportional to the square root of the stearate content. The investigations will be continued.

Vulcanization Kinetics of Natural Rubber Coagulated by Microorganisms with Use of a Vulcameter

2010 ◽  
Vol 160-162 ◽  
pp. 1181-1186 ◽  
Author(s):  
Zhi Feng Wang ◽  
Si Dong Li ◽  
Xiao Dong She
Keyword(s):  
Activation Energy ◽  
Natural Rubber ◽  
Rate Constants ◽  
Order Reaction ◽  
First Order Reaction ◽  
First Order ◽  
Second Stage ◽  
End Stage ◽  
Two Stages ◽  
Kinetics Of

Kinetics of vulcanization of natural rubber coagulated by microorganisms (NR-m) was studied with the use of a vulcameter. In the induction period of vulcanization, the time t0 of NR-m is shorter than that of natural rubber coagulated by acid (NR-a), and the rate constant k1/a of NR-m are greater than that of NR-a. Both the curing periods of NR-m and NR-a consist of two stages. The first stage follows first-order reaction. The rate constants k2 of NR-m in the first stage are greater than that of NR-a at the same temperature, and so are the activation energy E2. The second stage (end stage of the curing period) does not follow first-order reaction, and the calculated reaction order n of NR-m is in the range of 0.82-0.85, and that of NR-a is in the range of 0.64-0.72. The rate constants k3 of the second stage for NR -m are greater than that of NR-a at the same temperature, and so is the activation energy E3.

Vulcanization of Elastomers. 23. The Chemical Kinetics of Vulcanization Reactions and The Physical Properties of The Vulcanizates. I

1960 ◽  
Vol 33 (2) ◽  
pp. 335-341
Author(s):  
Walter Scheele ◽  
Karl-Heinz Hillmer
Keyword(s):  
Activation Energy ◽  
Physical Properties ◽  
Chemical Kinetics ◽  
Kcal Mole ◽  
First Order ◽  
Equilibrium Swelling ◽  
Kinetics Of ◽  
Kinetics Of Vulcanization ◽  
Limiting Value ◽  
Good Agreement

Abstract As a complement to earlier investigations, and in order to examine more closely the connection between the chemical kinetics and the changes with vulcanization time of the physical properties in the case of vulcanization reactions, we used thiuram vulcanizations as an example, and concerned ourselves with the dependence of stress values (moduli) at different degrees of elongation and different vulcanization temperatures. We found: 1. Stress values attain a limiting value, dependent on the degree of elongation, but independent of the vulcanization temperature at constant elongation. 2. The rise in stress values with the vulcanization time is characterized by an initial delay, which, however, is practically nonexistent at higher temperatures. 3. The kinetics of the increase in stress values with vulcanization time are both qualitatively and quantitatively in accord with the dependence of the reciprocal equilibrium swelling on the vulcanization time; both processes, after a retardation, go according to the first order law and at the same rate. 4. From the temperature dependence of the rate constants of reciprocal equilibrium swelling, as well as of the increase in stress, an activation energy of 22 kcal/mole can be calculated, in good agreement with the activation energy of dithiocarbamate formation in thiuram vulcanizations.

THE REACTION OF METHYL RADICALS WITH FORMALDEHYDE

1959 ◽  
Vol 37 (9) ◽  
pp. 1462-1468 ◽  
Author(s):  
A. R. Blake ◽  
K. O. Kutschke
Keyword(s):  
Activation Energy ◽  
Kinetic Analysis ◽  
Addition Reactions ◽  
Methyl Radicals ◽  
Kcal Mole ◽  
A Value ◽  
Abstraction Reaction ◽  
Butyl Peroxide

The pyrolysis of di-t-butyl peroxide has been reinvestigated and used as a source of methyl radicals to study the abstraction reaction between methyl radicals and formaldehyde. At low [HCHO]/[peroxide] ratios the system was simple enough for kinetic analysis, and a value of 6.6 kcal/mole was obtained for the activation energy. At higher [HCHO]/[peroxide] ratios the system became very complicated, possibly due to the increased importance of addition reactions.

scholarly journals KINETICS OF PALM OIL TRANSESTERIFICATION IN METHANOL WITH POTASSIUM HYDROXIDE AS A CATALYST

2010 ◽  
Vol 8 (2) ◽  
pp. 219-225
Author(s):  
Yoeswono Yoeswono ◽  
Triyono Triyono ◽  
Iqmal Tahir
Keyword(s):  
Activation Energy ◽  
Palm Oil ◽  
Rate Constants ◽  
Potassium Hydroxide ◽  
Catalyst Concentration ◽  
Time Interval ◽  
Pseudo First Order Reaction ◽  
Exponential Factor ◽  
Potassium Methoxide ◽  
First Order

A study on palm oil transesterification to evaluate the effect of some parameters in the reaction on the reaction kinetics has been carried out. Transesterification was started by preparing potassium methoxide from potassium hydroxide and methanol and then mixed it with the palm oil. An aliquot was taken at certain time interval during transesterification and poured into test tube filled with distilled water to stop the reaction immediately. The oil phase that separated from the glycerol phase by centrifugation was analyzed by 1H-NMR spectrometer to determine the percentage of methyl ester conversion. Temperature and catalyst concentration were varied in order to determine the reaction rate constants, activation energies, pre-exponential factors, and effective collisions. The results showed that palm oil transesterification in methanol with 0.5 and 1 % w/w KOH/palm oil catalyst concentration appeared to follow pseudo-first order reaction. The rate constants increase with temperature. After 13 min of reaction, More methyl esters were formed using KOH 1 % than using 0.5 % w/w KOH/palm oil catalyst concentration. The activation energy (Ea) and pre-exponential factor (A) for reaction using 1 % w/w KOH was lower than those using 0.5 % w/w KOH.   Keywords: palm oil, transesterification, catalyst, first order kinetics, activation energy, pre-exponential factor

Sign in / Sign up

Export Citation Format

Share Document