scholarly journals Supplier Evaluation and Selection in Automobile Industry

2019 ◽  
Author(s):  
Lokpriya Gaikwad ◽  
Vivek Sunnapwar
Keyword(s):  
Automobile Industry ◽  
Supplier Evaluation

scholarly journals Different Factors and Techniques for Supplier Evaluation and Selection in Automotive Industry of Punjab

2019 ◽  
Vol 8 (12) ◽  
pp. 1338-1345
Keyword(s):  
Automobile Industry ◽  
Supplier Selection ◽  
Selection Process ◽  
Point Of View ◽  
Critical Conditions ◽  
Supplier Evaluation ◽  
Common Criteria ◽  
Purchasing Department ◽  
A Company

In an automobile industry, to operate effectively the supply chain management, it is very important to perform the purchasing function effectively. It is the responsibility of the purchasing department in a company to choose the correct suppliers to purchase the required products. Thus, from purchase manager’s point of view, supplier evaluation technique is essential to choose the best supplier among the available suppliers. The literature addresses quality, delivery, technology, value and service are the five most common criteria used for supplier quality evaluation. In this article, approach of evaluation and selection of supplier has been presented as per the standards. Apart from these, the most important criteria to assess the quality of suppliers is based on a review of the literature and observation in practice. This in turn would help these organizations to review regularly and implement effective quality systems by following the set of standards. Also, nowadays most of the automobile companies have developed in-house pattern of procedures and software for the process of effective supplier selection. In the analysis, part per million equivalent technique is used to help the purchasing organization take a prompt and correct decision related to supplier selection process and evaluation in critical conditions

scholarly journals Green Supplier Evaluation and Selection with an Extended MABAC Method Under the Heterogeneous Information Environment

2019 ◽  
Vol 11 (23) ◽  
pp. 6616 ◽  
Author(s):  
Xu ◽  
Shi ◽  
Zhang ◽  
Liu
Keyword(s):  
Automobile Industry ◽  
Selection Model ◽  
Information Environment ◽  
Production Performance ◽  
Supplier Evaluation ◽  
Interval Numbers ◽  
Heterogeneous Information ◽  
Decision Context ◽  
Green Production ◽  
Green Suppliers

With the increasing awareness of global environmental protection, green production has become a significant part for enterprises to remain in a competitive position. For a manufacturing company, selecting the most suitable green supplier plays an important role in enhancing its green production performance. In this paper, we develop a new green supplier evaluation and selection model through the combination of heterogeneous criteria information and an extended multi-attributive border approximation area comparison (MABAC) method. Considering the complexity of decision context, heterogeneous information, including real numbers, interval numbers, trapezoidal fuzzy numbers, and linguistic hesitant fuzzy sets, is utilized to evaluate alternative suppliers with respect to the selected criteria. A maximizing consensus approach is constructed to determine the weight of each decision-maker based on incomplete weighting information. Then, the classical MABAC method is modified for ranking candidate green suppliers under the heterogeneous information environment. Finally, the developed green supplier selection model is applied in a case study from the automobile industry to illustrate its practicability and efficiency.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Influence of the War on the Automobile Industry

1915 ◽  
Vol 113 (10) ◽  
pp. 206-208 ◽  
Author(s):  
H. W. Perry
Keyword(s):  
Automobile Industry

Integrated FAHP-VIKOR model for green supplier selection in a Nickle coating SME

2020 ◽  
pp. 133-139
Author(s):  
Sanatan Ratna ◽  
B Kumar
Keyword(s):  
Staff Training ◽  
Supplier Selection ◽  
Fuzzy Ahp ◽  
Research Work ◽  
Supplier Evaluation ◽  
Green Supplier Selection ◽  
The Past ◽  
Coating Industry ◽  
Sustainability Issue ◽  
Selection Of

In the past few decades, there has been lot of focus on the issue of sustainability. This has occurred due to the growing concerns related to climate change and the growing awareness about environmental concerns. Also, the competition at global level has led to the search for the most sustainable route in the industries. The current research work deals with the selection of green supplier in a Nickle coating industry based on certain weighted green attributes. For this purpose, a hybrid tool comprising of Fuzzy AHP (Fuzzy Analytical Hierarchy) and VIKOR (VlseKriterijumska Optimizacija I Kompromisno Resenje) is used. The Fuzzy AHP is used for assigning proper weights to the selected criteria for supplier evaluation, while VIKOR is used for final supplier selection based on the weighted criteria. The three criterions for green supplier selection are, Ecological packaging, Corporate socio-environmental responsibility and Staff Training. The outcome of the integrated model may serve as a steppingstone to other SMEs in different sectors for selecting the most suitable supplier for addressing the sustainability issue.

Research on Development Strategy for China’s Powerful Automobile Industry

2018 ◽  
Vol 20 (1) ◽  
pp. 37
Author(s):  
Yang Dong ◽  
Yanhua Xu ◽  
Tianshu Pang ◽  
Peng Zou
Keyword(s):  
Development Strategy ◽  
Automobile Industry

Financial Performance of Automobile Industry in India

2012 ◽  
Vol 3 (1) ◽  
pp. 67-68
Author(s):  
P. Sankaran P. Sankaran ◽  
◽  
Dr. C. Gounasegaran Dr. C. Gounasegaran ◽  
Dr. R. Azhagaiah Dr. R. Azhagaiah
Keyword(s):  
Financial Performance ◽  
Automobile Industry
Sign in / Sign up

Export Citation Format

Share Document