scholarly journals Computational Analysis of a Lecture Room Ventilation System

2020 ◽  
Author(s):  
Abayomi Layeni ◽  
Collins Nwaokocha ◽  
Olalekan Olamide ◽  
Solomon Giwa ◽  
Samuel Tongo ◽  
...  
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Minimum Cost ◽  
Solar Chimney ◽  
Lecture Room ◽  
Room Ventilation System ◽  
Ventilation Systems

The level of Indoor Air Quality (IAQ) has become a big topic of research, and improving it using passive ventilation methods is imperative due to the cost saving potentials. Designing lecture buildings to use less energy or Zero Energy (ZE) has become more important, and analysing buildings before construction can save money in design changes. This research analyses the performance (thermal comfort [TC]) of a lecture room, investigate the use of passive ventilation methods and determine the energy-saving potential of the proposed passive ventilation method using Computational Fluid Dynamics (CFD). Results obtained showed that air change per hour at a wind velocity of 0.05 m/s was 3.10, which was below standards. Therefore, the lecture hall needs external passive ventilation systems (Solar Chimney [SC]) for improved indoor air quality at minimum cost. Also, it was observed that the proposed passive ventilation (SC) system with the size between 1 and 100 m3, made an improvement upon the natural ventilation in the room. There was a 66.69% increase after 10 years in the saving of energy and cost using Solar Chimney as compared to Fans, which depicts that truly energy and cost were saved using passive ventilation systems rather than mechanical ventilation systems.

Numerical and Experimental Modeling of Indoor Air Quality Inside a Conditioned Space with Mechanical Ventilation and DX-Air Conditioner

2020 ◽  
Vol 38 (9A) ◽  
pp. 1257-1275
Author(s):  
Wisam M. Mareed ◽  
Hasanen M. Hussen
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Ventilation System ◽  
Thermal Conditions ◽  
Airflow Rate ◽  
Air Conditioner ◽  
Breathing Zone ◽  
Lecture Room ◽  
Ventilation Performance

 Elevated CO2 rates in a building affect the health of the occupant. This paper deals with an experimental and numerical analysis conducted in a full-scale test room located in the Department of Mechanical Engineering at the University of Technology. The experiments and CFD were conducted for analyzing ventilation performance. It is a study on the effect of the discharge airflow rate of the ceiling type air-conditioner on ventilation performance in the lecture room with the mixing ventilation. Most obtained findings show that database and questionnaires analyzed prefer heights between 0.2 m to 1.2 m in the middle of an occupied zone and breathing zone height of between 0.75 m to 1.8 given in the literature surveyed. It is noticed the mismatch of internal conditions with thermal comfort, and indoor air quality recommended by [ASHRAE Standard 62, ANSI / ASHRAE Standard 55-2010]. CFD simulations have been carried to provide insights on the indoor air quality and comfort conditions throughout the classroom. Particle concentrations, thermal conditions, and modified ventilation system solutions are reported.

scholarly journals Indoor air quality improvement in natural ventilation using a fuzzy logic controller

2020 ◽  
pp. 1-19
Author(s):  
Cezary Kulis ◽  
Jarosław Müller
Keyword(s):  
Fuzzy Logic ◽  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Optical Sensors ◽  
Natural Ventilation ◽  
Fuzzy Logic Controller ◽  
Ventilation System ◽  
Raspberry Pi ◽  
Physical Parameters

The aim of the research was to design and validate the prototype of a device developed to improve the quality of indoor air by supporting the natural ventilation in building. A CO2 sensor and thermo-hygrometer were used to measure the physical parameters of the indoor air. The developed device is based on the Raspberry Pi single-board-computer (SBC) and optical sensors. The prototype casing was made using 3D printing technology. The software was written using the Python 2.7 programming language. The key algorithm of control uses fuzzy logic. The effectiveness of the developed device has been confirmed. The use of the device enabled improvement of the indoor air quality. The presented device may be a solution to improve the indoor air quality by supporting the ventilation system.

scholarly journals The Determination of Indoor Air Quality and Thermal Comfort with Different Space and Ventilation in the Teracce and Bungalow Houses

2021 ◽  
Vol 16 (3) ◽  
pp. 774-793
Author(s):  
Nur Baitul Izati Rasli ◽  
Nor Azam Ramli ◽  
Mohd Rodzi Ismail
Keyword(s):  
Air Quality ◽  
Thermal Comfort ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Physical Parameters ◽  
Air Contaminants ◽  
Code Of Practice ◽  
Air Movement

This study observed the influence of different ventilation, indoor and outdoor activities (i.e., cooking, praying, sweeping, gathering, and exhaust from motorcycle) between a bungalow house (i.e., stack and cross ventilation applications) and a terrace house (i.e., one-sided ventilation application). We appraised the indoor air quality (IAQ) and thermal comfort. We monitored the indoor air contaminants (i.e., TVOC, CO, CH2O, PM10, O3, and CO2) and specific physical parameters (i.e., T, RH, and AS) for four days in the morning (i.e., 6.00 a.m. – 9.00 a.m.), morning-evening (i.e., 11.00 a.m. – 2.00 p.m.), and evening-night (i.e., 5.00 p.m. – 8.00 p.m.) sessions. The results found that cooking activities are the major activities that contributed to the increase of the TVOC, CO, PM10, O3, and CO2 concentrations in the bungalow and terrace houses. However, IAQ exceeded the Industry Code of Practice on IAQ (ICOP) limit in the terrace house. The bungalow house applies stack and cross ventilation, double area, and a long pathway of indoor air contaminants movements. Besides that, the results indicated that cooking activities worsen the ventilation system because CO2 exceeded the ICOP limit on Day 2 at 74.1 % (evening-night session) and Day 3 at 13.2 % (morning session), 11% (morning-evening session), and 50.1 % (evening-night session). Moreover, the combination of mechanical (i.e., opened all fans) and natural ventilation (i.e., opened all doors, windows, and fans) is the best application in the house without a cooking ventilator with lower indoor air movement. Furthermore, the temperatures exceeding the ICOP limit of 23-26 °C for both bungalow and terrace houses could be lower indoor air movement, which is less than the ICOP limit of 0.15-0.5 m/s and high outdoor air temperature. Therefore, it is prudent to have an efficient ventilation system for acceptable indoor air quality and thermal comfort in the family house.

scholarly journals Research on Best Solution for Improving Indoor Air Quality and Reducing Energy Consumption in a High-Risk Radon Dwelling from Romania

2021 ◽  
Vol 18 (23) ◽  
pp. 12482
Author(s):  
Ion-Costinel Mareș ◽  
Tiberiu Catalina ◽  
Marian-Andrei Istrate ◽  
Alexandra Cucoș ◽  
Tiberius Dicu ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Energy Consumption ◽  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Heat Recovery ◽  
Natural Ventilation ◽  
High Efficiency ◽  
Ventilation System ◽  
Radon Level

The purpose of this article is the assessment of energy efficiency and indoor air quality for a single-family house located in Cluj-Napoca County, Romania. The studied house is meant to be an energy-efficient building with thermal insulation, low U-value windows, and a high efficiency boiler. Increasing the energy efficiency of the house leads to lower indoor air quality, due to lack of natural ventilation. As the experimental campaign regarding indoor air quality revealed, there is a need to find a balance between energy consumption and the quality of the indoor air. To achieve superior indoor air quality, the proposed mitigation systems (decentralized mechanical ventilation with heat recovery combined with a minimally invasive active sub-slab depressurization) have been installed to reduce the high radon level in the dwelling, achieving an energy reduction loss of up to 86%, compared to the traditional natural ventilation of the house. The sub-slab depressurization system was installed in the room with the highest radon level, while the local ventilation system with heat recovery has been installed in the exterior walls of the house. The results have shown significant improvement in the level of radon decreasing the average concentration from 425 to 70 Bq/m 3, respectively the carbon dioxide average of the measurements being around 760 ppm. The thermal comfort improves significantly also, by stabilizing the indoor temperature at 21 °C, without any important fluctuations. The installation of this system has led to higher indoor air quality, with low energy costs and significant energy savings compared to conventional ventilation (by opening windows).

scholarly journals Numerical Assessment of Seven Ventilation Systems for Social Residential Buildings based on Indoor Air Quality and Energy Consumption

2021 ◽  
Vol 2069 (1) ◽  
pp. 012181
Author(s):  
Guillaume Sérafin ◽  
Marc O. Abadie ◽  
Patrice Joubert
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Residential Buildings ◽  
Living Room ◽  
Internal Sources ◽  
Controlled Mechanical Systems ◽  
Ventilation Systems

Abstract This work presents a modelling approach for evaluating ventilation systems for their ability to provide good indoor air quality in dwellings. Infiltration and ventilation rates are defined by the conventional French 3CL-DPE standard. The case study is a two-bedroom apartment with a shared or separate kitchen and living room. Three natural ventilation options and four mechanical ventilation systems are compared with respect to exposure to PM2.5, NO2 and formaldehyde. Pollutant concentration levels are assessed in each room based on a scenario of daily occupancy, average annual outdoor concentrations and internal sources. The daily exposure of the occupants to the targeted substances allows the comparison of ventilation systems on the basis of the ULR-QAI index developed at LaSIE laboratory from La Rochelle University. For this case study, it results that controlled mechanical systems are much more efficient than natural ventilation systems, especially in the case of an open-plan kitchen.

scholarly journals Identifying mechanical ventilation issues in classrooms

2018 ◽  
Vol 44 ◽  
pp. 00055
Author(s):  
Julia Janiga ◽  
Joanna Krzempka ◽  
Aleksandra Szczerbińska
Keyword(s):  
Mechanical Ventilation ◽  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Ventilation System ◽  
Operating Time ◽  
Mechanically Ventilated ◽  
Ventilation Systems

This article focuses on the issues of indoor air quality in mechanically ventilated classrooms. The aim of the study was to determine the reasons for inadequate air quality reported by occupants. Two different ventilation systems were assessed by measuring CO2 and VOC concentrations in classrooms during operating time. Results showed that in both cases, CO2 levels in the air, even though mostly acceptable, were exceeded throughout the measuring periods on occasion. Based on obtained data, in both cases probable causes for reported ventilation system malfunctions were proposed.

scholarly journals Application of Wind as a Renewable Energy Source for Passive Cooling through Windcatchers Integrated with Wing Walls

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2536 ◽  
Author(s):  
Payam Nejat ◽  
Fatemeh Jomehzadeh ◽  
Hasanen Hussen ◽  
John Calautit ◽  
Muhd Abd Majid
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Natural Ventilation ◽  
Passive Cooling ◽  
Quality Factors ◽  
Ventilation Performance ◽  
Wing Walls ◽  
The Impact ◽  
Ventilation Systems

Generally, two-third of a building’s energy is consumed by heating, ventilation and air-conditioning systems. One green alternative for conventional air conditioner systems is the implementation of passive cooling. Wing walls and windcatchers are two prominent passive cooling techniques which use wind as a renewable resource for cooling. However, in low wind speed regions and climates, the utilization of natural ventilation systems is accompanied by serious uncertainties. The performance of ventilation systems can be potentially enhanced by integrating windcatchers with wing walls. Since previous studies have not considered this integration, in the first part of this research the effect of this integration on the ventilation performance was assessed and the optimum angle was revealed. However, there is still gap of this combination; thus, in the second part, the impact of wing wall length on the indoor air quality factors was evaluated. This research implemented a Computational Fluid Dynamics (CFD) method to address the gap. The CFD simulation was successfully validated with experimental data from wind tunnel tests related to the previous part. Ten different lengths from 10 cm to 100 cm were analyzed and it was found that the increase in wing wall length leads to a gradual reduction in ventilation performance. Hence, the length does not have a considerable influence on the indoor air quality factors. However, the best performance was seen in 10 cm, that could provide 0.8 m/s for supply air velocity, 790 L/s for air flow rate, 39.5 1/h for air change rate, 107 s for mean age of air and 92% for air change effectiveness.

scholarly journals Indoor air quality in natural-ventilated bedrooms in renovated Norwegian houses

2021 ◽  
Vol 246 ◽  
pp. 01001
Author(s):  
Vegard Heide ◽  
Silje Skyttern ◽  
Laurent Georges
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Indoor Environment ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Opening Angle ◽  
Single Family ◽  
Night Time ◽  
Window Opening

The objective of this work is to investigate the indoor environment in bedrooms ventilated by window opening during night-time. How window opening behaviour affects indoor air quality (IAQ), and how window opening behaviour and IAQ is influenced by external factors, are important questions. The context is renovation of detached wooden houses in Norway. To motivate building owners to renovate their ventilation system, it is important to know the typical indoor environment in bedrooms of existing buildings with natural ventilation. Ten bedrooms in six case houses were investigated by measuring temperature, relative humidity, CO2, particulate matter, formaldehyde and TVOC. The window opening angle was also logged with an accelerometer. The measurements were conducted over 2 to 3 weeks, during March and April. The dwellings were renovated single-family and terraced houses from 1950 – 80, in Trondheim. All the bedrooms had natural ventilation, and the occupants stated they used to open bedroom windows at night. Participants answered a questionnaire about motivations and habits regarding window opening. The most common reason given for not opening was low outdoor temperatures. The window opening behaviour was both predictable and continuous. Windows were open every night in most of the bedrooms, and most of the windows were opened to the same position every night. High CO2 levels during night were found in two bedrooms. In the other bedrooms, the CO2 concentration was satisfying during night-time, although higher concentrations were found in some bedrooms during daytime. Finally, indoor temperature measurements confirmed that many occupants prefer a low bedroom temperature.

scholarly journals Feasibility of a Passive Ventilation System with a Thermal Damper - Simulations and measurement results of an experimental house in a mild region of Japan -

2019 ◽  
Vol 111 ◽  
pp. 06047
Author(s):  
Motoya Hayashi ◽  
Hoon kim ◽  
Yoshinori Honma ◽  
Junichiro Matsunaga
Keyword(s):  
Air Quality ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Ventilation System ◽  
Indoor Environments ◽  
Air Supply ◽  
Measurement Results ◽  
Simulation Results ◽  
Ventilation Rates ◽  
Ventilation Systems

In order to retain good indoor air quality through the year in detached houses with passive ventilation systems, the authors investigated a mechanical control air-supply method. Firstly, indoor environments in houses with passive ventilation systems with thermal dampers, were examined using a simulation program (Fresh). Secondly, a passive ventilation system with a thermal damper, an under-floorheating system with a heat pump and were installed in an airtight house at Maebashi in Japan and measurements on its ventilation characteristics and indoor air quality were made. The simulation results showed that if the thermal damper is well tuned, this mechanically controlled air-supply opening keeps ventilation rates adequate through the year especially in airtight houses. The measurement results showed that the ventilation rates were kept above the required level through the year and the TVOC concentration decreases from 3000 to 200 μg/m3 in 5 months after the construction.

Sign in / Sign up

Export Citation Format

Share Document