scholarly journals Development of a Three-dimensional Finite Element Model for a Unidirectional Carbon Fiber Reinforced Plastic Based on X-ray Computed Tomography Images and the Numerical Simulation on Compression

2017 ◽  
Vol 43 (6) ◽  
pp. 219-225
Author(s):  
Keisuke IIZUKA ◽  
Masahito UEDA ◽  
Takuya TAKAHASHI ◽  
Akinori YOSHIMURA ◽  
Masahiro NAKAYAMA
Keyword(s):  
Three Dimensional ◽  
Element Model ◽  
Carbon Fiber Reinforced Plastic ◽  
X Ray ◽  
Fiber Reinforced Plastic ◽  
Computed Tomography Images ◽  
Reinforced Plastic ◽  
Dimensional Finite Element ◽  
X Ray Computed ◽  
Three Dimensional Finite Element

Evaluation of sternum closure methods by means of a nonlinear finite element analysis

2019 ◽  
Vol 233 (12) ◽  
pp. 1282-1291 ◽  
Author(s):  
Suleyman Nazif Orhan ◽  
Mehmet Hamit Ozyazicioglu
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Plastic Material ◽  
Steel Wire ◽  
Three Dimensional ◽  
Element Model ◽  
Element Analysis ◽  
Computed Tomography Images ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The main purpose of this study is to develop a validated three-dimensional finite element model of sternum closure techniques. For this aim, the finite element method analysis results of three closure methods were compared with experimental test results. Also, three more closure techniques are simulated numerically to study the effect of the number of wires used in the manubrium and xiphoid regions. A three-dimensional model of polyurethane sternum foam was created based on computed tomography images. Six different closure techniques using steel wire, steel bands and ZipFix bands were modeled on the sternum and transferred into a three-dimensional finite element model. The sternum was modeled as an isotropic bilinear-elasto-plastic material, and nonlinear contact conditions were applied. The models were analyzed under lateral distraction loading, and load-displacement curves were obtained from displacements at the incision line. Allowable loads and stiffness values of the methods were evaluated from these curves. The results showed the importance of the including material as well as geometric nonlinearities in the simulations to obtain realistic results from the numerical analyses. Also, the analyses showed that closures that include steel or ZipFix bands are superior to conventional wiring, and addition of a single wire at the manubrium and xiphoid regions significantly improved the efficiency of the closure techniques.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Internal Force on and Deformation of Steel Assembled Supporting Structure of Foundation Pit under Thermal Stress

2021 ◽  
Vol 11 (5) ◽  
pp. 2225
Author(s):  
Fu Wang ◽  
Guijun Shi ◽  
Wenbo Zhai ◽  
Bin Li ◽  
Chao Zhang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Bending Moment ◽  
High Strength ◽  
Element Model ◽  
Internal Force ◽  
Foundation Pit ◽  
Dimensional Finite Element ◽  
Influence Of Temperature On ◽  
Scale Experiment ◽  
Three Dimensional Finite Element

The steel assembled support structure of a foundation pit can be assembled easily with high strength and recycling value. Steel’s performance is significantly affected by the surrounding temperature due to its temperature sensitivity. Here, a full-scale experiment was conducted to study the influence of temperature on the internal force and deformation of supporting structures, and a three-dimensional finite element model was established for comparative analysis. The test results showed that under the temperature effect, the deformation of the central retaining pile was composed of rigid rotation and flexural deformation, while the adjacent pile of central retaining pile only experienced flexural deformation. The stress on the retaining pile crown changed little, while more stress accumulated at the bottom. Compared with the crown beam and waist beam 2, the stress on waist beam 1 was significantly affected by the temperature and increased by about 0.70 MPa/°C. Meanwhile, the stress of the rigid panel was greatly affected by the temperature, increasing 78% and 82% when the temperature increased by 15 °C on rigid panel 1 and rigid panel 2, respectively. The comparative simulation results indicated that the bending moment and shear strength of pile 1 were markedly affected by the temperature, but pile 2 and pile 3 were basically stable. Lastly, as the temperature varied, waist beam 2 had the largest change in the deflection, followed by waist beam 1; the crown beam experienced the smallest change in the deflection.

Process Modeling in Laser Deposition of Multilayer SS410 Steel

2007 ◽  
Vol 129 (6) ◽  
pp. 1028-1034 ◽  
Author(s):  
Liang Wang ◽  
Sergio Felicelli
Keyword(s):  
Phase Transformation ◽  
Temperature Distribution ◽  
Three Dimensional ◽  
Element Model ◽  
Traverse Speed ◽  
Processing Parameters ◽  
Dimensional Finite Element ◽  
Net Shaping ◽  
Three Dimensional Finite Element ◽  
Continuous Cooling Transformation Diagram

A three-dimensional finite element model was developed to predict the temperature distribution and phase transformation in deposited stainless steel 410 (SS410) during the Laser Engineered Net Shaping (LENS™) rapid fabrication process. The development of the model was carried out using the SYSWELD software package. The model calculates the evolution of temperature in the part during the fabrication of a SS410 plate. The metallurgical transformations are taken into account using the temperature-dependent material properties and the continuous cooling transformation diagram. The ferritic and martensitic transformation as well as austenitization and tempering of martensite are considered. The influence of processing parameters such as laser power and traverse speed on the phase transformation and the consequent hardness are analyzed. The potential presence of porosity due to lack of fusion is also discussed. The results show that the temperature distribution, the microstructure, and hardness in the final part depend significantly on the processing parameters.

Sign in / Sign up

Export Citation Format

Share Document