Numerical simulation of S-shaped inlet under the intake total pressure distortion

During the development of the stealth fighter, the S-shaped inlet enters the designer’s vision because it has better stealth than bump inlet and straight inlet. During the use of the S-shaped inlet, due to its structural reasons, secondary flow is likely to occur in the curved section, which directly causes the flow state to be changeable and complicated. Therefore, this paper takes the S-shaped inlet as the research object to analyzes the steady flow field simulation under uniform inlet condition and distortion inlet condition and analyze the flow field of the airflow and the total pressure of each section under the S-shaped inlet by changing the intake distortion conditions with CFX software. The results show that although the S-shaped inlet will occur total pressure distortion under uniform intake. However, when the S-shaped inlet work under certain flight conditions, the level of total pressure distortion will be smaller than the uniform inlet condition, which can improve the air intake performance. Finally, it can be inferred that with use of the S-shaped intake port, the deterioration of distortion may be prevented under certain specific intake conditions.

Effect of Compressor Inlet Condition on Supercritical Carbon Dioxide Compressor Performance

Supercritical carbon dioxide (S-CO2) Brayton power cycle has attracted a lot of attention around the world in energy conversion field. It takes advantage of the high density of CO2 near the critical point while maintaining low viscosity to reduce compressor power and achieve high cycle efficiency. However, as CO2 approaches to its critical point, the thermodynamic properties of CO2 vary dramatically with small changes in temperature or pressure. As a result, the density of the working fluid varies significantly at the compressor inlet in the practical cycle if operating near the critical point, especially for small-scale cycles and air-cooled cycles, which leads to compressors operating out of the flow range, even being damaged. Concerns of large density variations at the inlet of the compressor result in S-CO2 compressor designers selecting compressor inlet conditions away from the critical point, thereby increasing compressor power. In this paper, a criterion to choose inlet pressure and inlet temperature of compressors as the design inlet condition is proposed, which is guaranteeing ±50% change in inlet specific volume within ±3 °C variation in inlet temperature. By the criterion, 8 MPa and 34.7 °C is selected as the design inlet condition. According to design requirements of the cycle, a S-CO2 centrifugal compressor is designed through 1-D design methodology. Based on the two-zone model, the effects of compressor inlet condition including inlet pressure and inlet temperature on the compressor performance are analyzed in detail. In practical operation, the compressor inlet condition is varied. Thus, an accurate prediction of compressor performance under different inlet conditions is necessary. The traditional correction method is not suitable for S-CO2 compressor. Dimensionless specific enthalpy rise is used to correct pressure ratio by the real gas table. And the S-CO2 compressor performance can be predicted correctly under different inlet conditions.

Large Eddy Simulations of a Highly Loaded Transonic Blade With Separated Flow

Efficient design of highly loaded pressure blades often leads to the generation of a separation bubble on the pressure side of highly curved blades. For this specific region, fundamental, numerical and experimental studies have indicated the importance of the turbulence present in the main stream in determining the size of the bubble before its reattachment to the blade. Despite this important finding, many complex phenomena remain and are still present and can influence the overall flow response. In this paper, explorations of high-fidelity unsteady Large Eddy Simulations of a separated flow are studied for the high pressure T120 blade from the European project AITEB II (Aerothermal Investigation on Turbine Endwalls and Blades). For this investigation, simulations are carried out at the nominal operating point with and without synthetic turbulence injection at the inlet condition to comply with the specification from the experiment. Based on these predictions, the near wall flow structure and turbulent fields are specifically investigated in an attempt to identify the key mechanisms introduced by the turbulent main stream flow. Results show that the turbulence specification at the inlet enables the recovery of the correct pressure distribution on the blade surface contrary to the laminar inlet condition if compared to the experiment. Investigations of the boundary layer profiles show a strong impact of the freestream turbulence on the shape factor from the leading edge. As a consequence, the recirculation bubble located downstream on the pressure side is impacted and reduced when turbulence is injected. Due to this change in mean flow topology, the mass flow distribution in the passage appears strongly affected. Investigations of loss fields furthermore show that the freestream turbulence dramatically increases the loss production within the computational domain.