target loading
Recently Published Documents


TOTAL DOCUMENTS

11
(FIVE YEARS 0)

H-INDEX

3
(FIVE YEARS 0)

Sensors ◽  
2018 ◽  
Vol 19 (1) ◽  
pp. 67
Author(s):  
Kewei Zhang ◽  
Zhe Chen ◽  
Qianke Zhu ◽  
Yong Jiang ◽  
Wenfeng Liu ◽  
...  

We established the vibration governing equation for a magnetoelastic (ME) biosensor with target loading in liquid. Based on the equation, a numerical simulation approach was used to determine the effect of the target loading position and viscous damping coefficient on the node (“blind points”) and mass sensitivity (Sm) of an ME biosensor under different order resonances. The results indicate that viscous damping force causes the specific nodes shift but does not affect the overall variation trend of Sm as the change of target loading position and the effect on Sm gradually reduces when the target approaches to the node. In addition, Sm decreases with the increase of viscous damping coefficient but the tendency becomes weak at high-order resonance. Moreover, the effect of target loading position on Sm decreases with the increase of viscous damping coefficient. Finally, the results provide certain guidance on improving the mass sensitivity of an ME biosensor in liquid by controlling the target loading position.



2016 ◽  
Vol 158 (B2) ◽  
Author(s):  
J P Pilate ◽  
F C Gerhardt ◽  
S E Norris ◽  
R G J Flay

This paper investigates an inverse process for the design of yacht sails. The method is described and then applied to the design of optimal sails for a specific yacht. The proposed inverse method generates the three-dimensional shapes of a headsail and mainsail from prescribed loading (i.e. differential pressure) distributions, accounts for the effect of the sea surface, and also simulates the twist and shear of the incoming flow. The uncoupled iterative routine solves a sequence of analysis steps so that the sail shapes are deformed in such a way that their updated loading distributions converge to the specified target distributions. During each iteration equations derived from two-dimensional Thin Aerofoil Theory, calculate a geometry correction from the difference between the current and target loading distributions. This correction is applied to the sail geometry, and a vortex lattice method code calculates the updated three-dimensional differential pressure distributions, which are again compared to the target distributions. Usually only five iterations are required to converge to sail shapes that have the target loading distributions. The inverse method has been validated by inverting the traditional way of analysing sails, i.e. a set of sails with known geometry has been analysed and the loading distributions on the headsail and mainsail were calculated. These distributions were then used as an input for the inverse code. It was found that the difference in camber between the original sails and the calculated geometry is less than 0.01% of camber at the mid-span of the sails. The second part of the paper presents two methods for the design of optimal sails for a yacht. One of the methods uses the more traditional analysis approach, while the other employs the inverse method described in this paper. The optimisation is performed for a Transpac 52 yacht in 12 knots (6.5 m/s) of true wind speed to obtain the best velocity made good. Results from both methods are presented and discussed and it is found that the results in terms of boat speed are similar although the trims differ slightly. However, the new inverse method is approximately nine times faster than the traditional analysis approach.



2015 ◽  
Vol 15 (6) ◽  
pp. 443-450
Author(s):  
Jong Sang Yeon ◽  
Kyu Bum Sim ◽  
Okjeong Lee ◽  
Sangdan Kim ◽  
Eung Seok Kim


2014 ◽  
Vol 40 (2) ◽  
pp. 137-148 ◽  
Author(s):  
Dragan Čakmak ◽  
Jelena Beloica ◽  
Veljko Perović ◽  
Ratko Kadović ◽  
Vesna Mrvić ◽  
...  

Abstract Acidification, as a form of soil degradation is a process that leads to permanent reduction in the quality of soil as the most important natural resource. The process of soil acidification, which in the first place implies a reduction in soil pH, can be caused by natural processes, but also considerably accelerated by the anthropogenic influence of excessive S and N emissions, uncontrolled deforestation, and intensive agricultural processes. Critical loads, i.e. the upper limit of harmful depositions (primarily of S and N) which will not cause damages to the ecosystem, were determined in Europe under the auspices of the Executive Committee of the CLRTAP in 1980. These values represent the basic indicators of ecosystem stability to the process of acidification. This paper defines the status of acidification for the period up to 2100 in relation to the long term critical and target loading of soil with S and N on the territory of Krupanj municipality by applying the VSD model. The Inverse Distance Weighting (IDW) geostatistic module was used as the interpolation method. Land management, particularly in areas susceptible to acidification, needs to be focused on well-balanced agriculture and use of crops/seedlings to achieve the optimum land use and sustainable productivity for the projected 100-year period.



2010 ◽  
Vol 17 (3) ◽  
pp. 317-328 ◽  
Author(s):  
Andrew Wardlaw ◽  
William Fourney ◽  
Ulrich Leiste

The pressure on a flat plate suspended over a submerged detonation is measured and simulated. Calculation and experiment are in relatively good agreement, although there is variation in experimental results and simulations are sensitive, near the centerline, to the computational details. This sensitivity is linked to the instability of the accelerating plume, typical of a Richtmyer-Meshkov instability. The plate loading features an initial force at plate center, followed by an expanding circular loading pattern. The initial load is due to plume impact, while the circular load arises from the impact of water transported up the edges of the explosion cavity.



2009 ◽  
Author(s):  
L. L. Gibson ◽  
B. Bartram ◽  
D. M. Dattelbaum ◽  
S. A. Sheffield ◽  
D. B. Stahl ◽  
...  


Author(s):  
Richard A. Ferrieri ◽  
David L. Alexoff ◽  
David J. Schlyer ◽  
Alfred P. Wolf


1960 ◽  
Vol 4 ◽  
pp. 194-200
Author(s):  
Peter B. Whitcomb

AbstractThe Hilger & Watts microfocus X-ray diffraction instrument has been redesigned to provide a tube allowing up to three times the target loading of previous tubes. The line focus, 6 mm × 100 μ, increases the target loading to 50 kv dc, 10 ma. To accomplish this, a new high-power transformer is provided with a special demountable tube and anode assembly with suitable cooling provided. The original 40 μ and 100 μ tubes are interchangeable with the new tube. Considerable gains in performance with photographic methods are indicated, but more notable is the increase in resolution when the microfocus unit is used as a source of X-ray for a diffractometer. The diffractometer can now be operated under the same conditions as those required for a conventional tube but with the much higher resolution.



Sign in / Sign up

Export Citation Format

Share Document