Estimating picking errors in near‐surface seismic data to enable their time‐lapse interpretation of hydrosystems

2018 ◽  
Vol 16 (6) ◽  
pp. 613-625 ◽  
Author(s):  
M. Dangeard ◽  
L. Bodet ◽  
S. Pasquet ◽  
J. Thiesson ◽  
R. Guérin ◽  
...  
Keyword(s):  
Geophysics ◽  
2020 ◽  
Vol 85 (2) ◽  
pp. V169-V181 ◽  
Author(s):  
Daniele Colombo ◽  
Diego Rovetta ◽  
Ernesto Sandoval-Curiel ◽  
Apostolos Kontakis

We have developed a new framework for performing surface-consistent amplitude balancing and deconvolution of the near-surface attenuation response. Both approaches rely on the early arrival waveform of a seismic recording, which corresponds to the refracted or, more generally speaking, to the transmitted energy from a seismic source. The method adapts standard surface-consistent amplitude compensation and deconvolution to the domain of refracted/transmitted waves. A sorting domain specific for refracted energy is extended to the analysis of amplitude ratios of each trace versus a reference average trace to identify amplitude residuals that are inverted for surface consistency. The residual values are either calculated as a single scalar value for each trace or as a function of frequency to build a surface-consistent deconvolution operator. The derived operators are then applied to the data to obtain scalar amplitude balancing or amplitude balancing with spectral shaping. The derivation of the operators around the transmitted early arrival waveforms allows for deterministically decoupling the near-surface attenuation response from the remaining seismic data. The developed method is fully automatic and does not require preprocessing of the data. As such, it qualifies as a standard preprocessing tool to be applied at the early stages of seismic processing. Applications of the developed method are provided for a case in a complex, structure-controlled wadi, for a seismic time-lapse [Formula: see text] land monitoring case, and for an exploration area with high dunes and sabkhas producing large frequency-dependent anomalous amplitude responses. The new development provides an effective tool to enable better reservoir characterization and monitoring with land seismic data.


Geophysics ◽  
2014 ◽  
Vol 79 (6) ◽  
pp. B243-B252 ◽  
Author(s):  
Peter Bergmann ◽  
Artem Kashubin ◽  
Monika Ivandic ◽  
Stefan Lüth ◽  
Christopher Juhlin

A method for static correction of time-lapse differences in reflection arrival times of time-lapse prestack seismic data is presented. These arrival-time differences are typically caused by changes in the near-surface velocities between the acquisitions and had a detrimental impact on time-lapse seismic imaging. Trace-to-trace time shifts of the data sets from different vintages are determined by crosscorrelations. The time shifts are decomposed in a surface-consistent manner, which yields static corrections that tie the repeat data to the baseline data. Hence, this approach implies that new refraction static corrections for the repeat data sets are unnecessary. The approach is demonstrated on a 4D seismic data set from the Ketzin [Formula: see text] pilot storage site, Germany, and is compared with the result of an initial processing that was based on separate refraction static corrections. It is shown that the time-lapse difference static correction approach reduces 4D noise more effectively than separate refraction static corrections and is significantly less labor intensive.


2020 ◽  
Vol 10 (5) ◽  
pp. 1875
Author(s):  
Helene Meling Stemland ◽  
Tor Arne Johansen ◽  
Bent Ole Ruud

The terrestrial Arctic is warming rapidly, causing changes in the degree of freezing of the upper sediments, which the mechanical properties of unconsolidated sediments strongly depend upon. This study investigates the potential of using time-lapse surface seismics to monitor thawing of currently (partly) frozen ground utilizing synthetic and real seismic data. First, we construct a simple geological model having an initial temperature of −5 °C, and infer constant surface temperatures of −5 °C, +1 °C, +5 °C, and +10 °C for four years to this model. The geological models inferred by the various thermal regimes are converted to seismic models using rock physics modeling and subsequently seismic modeling based on wavenumber integration. Real seismic data reflecting altered surface temperatures were acquired by repeated experiments in the Norwegian Arctic during early autumn to mid-winter. Comparison of the surface wave characteristics of both synthetic and real seismic data reveals time-lapse effects that are related to thawing caused by varying surface temperatures. In particular, the surface wave dispersion is sensitive to the degree of freezing in unconsolidated sediments. This demonstrates the potential of using surface seismics for Arctic climate monitoring, but inversion of dispersion curves and knowledge of the local near-surface geology is important for such studies to be conclusive.


Geophysics ◽  
2015 ◽  
Vol 80 (2) ◽  
pp. Q15-Q26 ◽  
Author(s):  
Dmitry Alexandrov ◽  
Andrey Bakulin ◽  
Roy Burnstad ◽  
Boris Kashtan

Time-lapse surface seismic monitoring typically suffers from different sources of nonrepeatability related to acquisition imperfections as well as due to complexity of the subsurface. Placing sources and receivers below the surface can improve seismic data repeatability. However, it is not always possible to bury a large number of sources, and therefore the next best option is monitoring with surface sources and buried sensors. We have discovered that redatuming of surface sources to the shallow buried receivers produced a reliable image of target reflectors despite the fact that receivers were placed in the near-field zone of the source. We redatumed data with the virtual source method using crosscorrelation of the measured wavefields. We found that redatuming also reduced nonrepeatability of seismic data associated with changes in acquisition geometry, variable source coupling, and daily/seasonal variations in the near surface. We developed these results with a synthetic case study using a realistic 1D elastic model with a free surface and acquisition geometry from an actual field experiment conducted in Saudi Arabia.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sherif M. Hanafy ◽  
Hussein Hoteit ◽  
Jing Li ◽  
Gerard T. Schuster

AbstractResults are presented for real-time seismic imaging of subsurface fluid flow by parsimonious refraction and surface-wave interferometry. Each subsurface velocity image inverted from time-lapse seismic data only requires several minutes of recording time, which is less than the time-scale of the fluid-induced changes in the rock properties. In this sense this is real-time imaging. The images are P-velocity tomograms inverted from the first-arrival times and the S-velocity tomograms inverted from dispersion curves. Compared to conventional seismic imaging, parsimonious interferometry reduces the recording time and increases the temporal resolution of time-lapse seismic images by more than an order-of-magnitude. In our seismic experiment, we recorded 90 sparse data sets over 4.5 h while injecting 12-tons of water into a sand dune. Results show that the percolation of water is mostly along layered boundaries down to a depth of a few meters, which is consistent with our 3D computational fluid flow simulations and laboratory experiments. The significance of parsimonious interferometry is that it provides more than an order-of-magnitude increase of temporal resolution in time-lapse seismic imaging. We believe that real-time seismic imaging will have important applications for non-destructive characterization in environmental, biomedical, and subsurface imaging.


2021 ◽  
Vol 109 ◽  
pp. 103363
Author(s):  
Ben Roche ◽  
Jonathan M. Bull ◽  
Hector Marin-Moreno ◽  
Timothy G. Leighton ◽  
Ismael H. Falcon-Suarez ◽  
...  

Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. U67-U76 ◽  
Author(s):  
Robert J. Ferguson

The possibility of improving regularization/datuming of seismic data is investigated by treating wavefield extrapolation as an inversion problem. Weighted, damped least squares is then used to produce the regularized/datumed wavefield. Regularization/datuming is extremely costly because of computing the Hessian, so an efficient approximation is introduced. Approximation is achieved by computing a limited number of diagonals in the operators involved. Real and synthetic data examples demonstrate the utility of this approach. For synthetic data, regularization/datuming is demonstrated for large extrapolation distances using a highly irregular recording array. Without approximation, regularization/datuming returns a regularized wavefield with reduced operator artifacts when compared to a nonregularizing method such as generalized phase shift plus interpolation (PSPI). Approximate regularization/datuming returns a regularized wavefield for approximately two orders of magnitude less in cost; but it is dip limited, though in a controllable way, compared to the full method. The Foothills structural data set, a freely available data set from the Rocky Mountains of Canada, demonstrates application to real data. The data have highly irregular sampling along the shot coordinate, and they suffer from significant near-surface effects. Approximate regularization/datuming returns common receiver data that are superior in appearance compared to conventional datuming.


Geophysics ◽  
2015 ◽  
Vol 80 (2) ◽  
pp. WA61-WA67 ◽  
Author(s):  
Zhaoyun Zong ◽  
Xingyao Yin ◽  
Guochen Wu ◽  
Zhiping Wu

Elastic inverse-scattering theory has been extended for fluid discrimination using the time-lapse seismic data. The fluid factor, shear modulus, and density are used to parameterize the reference medium and the monitoring medium, and the fluid factor works as the hydrocarbon indicator. The baseline medium is, in the conception of elastic scattering theory, the reference medium, and the monitoring medium is corresponding to the perturbed medium. The difference in the earth properties between the monitoring medium and the baseline medium is taken as the variation in the properties between the reference medium and perturbed medium. The baseline and monitoring data correspond to the background wavefields and measured full fields, respectively. And the variation between the baseline data and monitoring data is taken as the scattered wavefields. Under the above hypothesis, we derived a linearized and qualitative approximation of the reflectivity variation in terms of the changes of fluid factor, shear modulus, and density with the perturbation theory. Incorporating the effect of the wavelet into the reflectivity approximation as the forward solver, we determined a practical prestack inversion approach in a Bayesian scheme to estimate the fluid factor, shear modulus, and density changes directly with the time-lapse seismic data. We evaluated the examples revealing that the proposed approach rendered the estimation of the fluid factor, shear modulus, and density changes stably, even with moderate noise.


Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. C81-C92 ◽  
Author(s):  
Helene Hafslund Veire ◽  
Hilde Grude Borgos ◽  
Martin Landrø

Effects of pressure and fluid saturation can have the same degree of impact on seismic amplitudes and differential traveltimes in the reservoir interval; thus, they are often inseparable by analysis of a single stacked seismic data set. In such cases, time-lapse AVO analysis offers an opportunity to discriminate between the two effects. We quantify the uncertainty in estimations to utilize information about pressure- and saturation-related changes in reservoir modeling and simulation. One way of analyzing uncertainties is to formulate the problem in a Bayesian framework. Here, the solution of the problem will be represented by a probability density function (PDF), providing estimations of uncertainties as well as direct estimations of the properties. A stochastic model for estimation of pressure and saturation changes from time-lapse seismic AVO data is investigated within a Bayesian framework. Well-known rock physical relationships are used to set up a prior stochastic model. PP reflection coefficient differences are used to establish a likelihood model for linking reservoir variables and time-lapse seismic data. The methodology incorporates correlation between different variables of the model as well as spatial dependencies for each of the variables. In addition, information about possible bottlenecks causing large uncertainties in the estimations can be identified through sensitivity analysis of the system. The method has been tested on 1D synthetic data and on field time-lapse seismic AVO data from the Gullfaks Field in the North Sea.


Sign in / Sign up

Export Citation Format

Share Document