Polyurethane and unsaturated polyester hybrid networks: Chemorheological and dielectric study for the resin transfer molding process (RTM)

This study investigated the effect of heatingtime during heat treatment on mechanical and physical properties of the kenaf fiber and its composites. Kenafbast fibers were modified by heat treatmentat 140°C for2.5, 5, 7.5, 10 and 12.5 hours. Composites were fabricated by resin transfer molding process with unsaturated polyester as matrices and needle-punched kenaf fiber mat as reinforces. The fiberswerecharacterized by Fourier Transform-Infra Red (FT-IR) and X-Ray Diffraction (XRD). FT-IR resultsshowedthe changesin intensity ofhemicelluloce wavelength (1736 cm-1). Besides XRD observation also confirmed the increase of cellulose content in kenafthat described to the increase of crystallinity index ofkenaf fiber with heat treatment. The single fiber strength investigation stated that the highest strength and modulus was obtained bykenaf fiber heated for10hours indrying oven. SEM observation showed the decreasing numbers of impuritieson thefibers surface with fiber treatment compared to untreated kenaf fibers. The flexural properties of composites showed a similar trend to fiber strength, but the fracture toughnesshas showedcontrary results.

Download Full-text

Correction to: numerical study to control the filler distribution in fibrous media during the particle-filled resin transfer molding process

The International Journal of Advanced Manufacturing Technology ◽

10.1007/s00170-021-07062-x ◽

2021 ◽

Author(s):

Ahmed El Moumen ◽

Abdelghani Saouab ◽

Nihad A. Siddig ◽

Laurent Bizet ◽

Abdellatif Imad

Keyword(s):

Numerical Study ◽

Resin Transfer Molding ◽

Fibrous Media ◽

Molding Process ◽

Transfer Molding ◽

Filler Distribution

Download Full-text

A Conceptional Approach of Resin-Transfer-Molding to Rosin-Sourced Epoxy Matrix Green Composites

Aerospace ◽

10.3390/aerospace8010005 ◽

2020 ◽

Vol 8 (1) ◽

pp. 5

Author(s):

Sicong Yu ◽

Xufeng Zhang ◽

Xiaoling Liu ◽

Chris Rudd ◽

Xiaosu Yi

Keyword(s):

Composite Laminates ◽

Resin Transfer Molding ◽

High Viscosity ◽

Ramie Fiber ◽

Liquid Composite Molding ◽

Curing Agent ◽

Molding Process ◽

Transfer Molding ◽

Low Viscosity ◽

Composite Molding

In this concept-proof study, a preform-based RTM (Resin Transfer Molding) process is presented that is characterized by first pre-loading the solid curing agent onto the preform, and then injecting the liquid nonreactive resin with an intrinsically low viscosity into the mold to infiltrate and wet the pre-loaded preform. The separation of resin and hardener helped to process inherently high viscosity resins in a convenient way. Rosin-sourced, anhydrite-cured epoxies that would normally be regarded as unsuited to liquid composite molding, were thus processed. Rheological tests revealed that by separating the anhydrite curing agent from a formulated RTM resin system, the remaining epoxy liquid had its flowtime extended. C-scan and glass transition temperature tests showed that the preform pre-loaded with anhydrite was fully infiltrated and wetted by the liquid epoxy, and the two components were diffused and dissolved with each other, and finally, well reacted and cured. Composite laminates made via this approach exhibited roughly comparable quality and mechanical properties with prepreg controls via autoclave or compression molding, respectively. These findings were verified for both carbon and ramie fiber composites.

Download Full-text

Development of resin transfer molding process using scaling down strategy

Polymer Composites ◽

10.1002/pc.22821 ◽

2013 ◽

Vol 35 (9) ◽

pp. 1683-1689 ◽

Cited By ~ 5

Author(s):

Raghu Raja Pandiyan Kuppusamy ◽

Swati Neogi

Keyword(s):

Resin Transfer Molding ◽

Molding Process ◽

Transfer Molding ◽

Scaling Down

Download Full-text

Resin transfer molding process: a numerical and experimental investigation

The International Journal of Multiphysics ◽

10.1260/1750-9548.7.2.125 ◽

2013 ◽

Vol 7 (2) ◽

pp. 125-136 ◽

Cited By ~ 9

Author(s):

Iran de Oliveira ◽

Sandro Amico ◽

Jeferson Souza ◽

Antonio de Lima

Keyword(s):

Experimental Investigation ◽

Resin Transfer Molding ◽

Molding Process ◽

Transfer Molding

Download Full-text

A Closed Form Solution for Flow During the Vacuum Assisted Resin Transfer Molding Process

Journal of Manufacturing Science and Engineering ◽

10.1115/1.1285907 ◽

1999 ◽

Vol 122 (3) ◽

pp. 463-475 ◽

Cited By ~ 66

Author(s):

K-T. Hsiao ◽

R. Mathur ◽

S. G. Advani ◽

J. W. Gillespie, ◽

B. K. Fink

Keyword(s):

Closed Form ◽

Scaling Laws ◽

Resin Transfer Molding ◽

Closed Form Solution ◽

Form Solution ◽

Flow Front ◽

Molding Process ◽

Transfer Molding ◽

Front Region ◽

Insight Into

A closed form solution to the flow of resin in vacuum assisted resin transfer molding process (VARTM) has been derived. VARTM is used extensively for affordable manufacturing of large composite structures. During the VARTM process, a highly permeable distribution medium is incorporated into the preform as a surface layer. During infusion, the resin flows preferentially across the surface and simultaneously through the preform giving rise to a complex flow front. The analytical solution presented here provides insight into the scaling laws governing fill times and resin inlet placement as a function of the properties of the preform, distribution media and resin. The formulation assumes that the flow is fully developed and is divided into two regimes: a saturated region with no crossflow and a flow front region where the resin is infiltrating into the preform from the distribution medium. The flow front region moves with a uniform velocity. The law of conservation of mass and Darcy’s Law for flow through porous media are applied in each region. The resulting equations are nondimensionalized and are solved to yield the flow front shape and the development of the saturated region. It is found that the flow front is parabolic in shape and the length of the saturated region is proportional to the square root of the time elapsed. The results thus obtained are compared to data from full scale simulations and an error analysis of the solution was carried out. It was found that the time to fill is determined with a high degree of accuracy while the error in estimating the flow front length, d, increases with a dimensionless parameter ε=K2xxh22/K2yyd2. The solution allows greater insight into the process physics, enables parametric and optimization studies and can reduce the computational cost of full-scale 3-dimensional simulations. A parametric study is conducted to establish the sensitivity of flow front velocity to the distribution media/preform thickness ratio and permeabilities and preform porosity. The results provide insight into the scaling laws for manufacturing of large scale structures by VARTM. [S1087-1357(00)02002-5]

Download Full-text