The Chaotic Oscillations of High-Speed Milling

2006 ◽  
pp. 147-158 ◽  
Author(s):  
G. Stépán ◽  
R. Szalai ◽  
S. J. Hogan
Keyword(s):  
High Speed ◽  
Chaotic Oscillations ◽  
High Speed Milling

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Trochoidal machining for the high-speed milling of pockets

2016 ◽  
Vol 233 ◽  
pp. 29-43 ◽  
Author(s):  
Wu Shixiong ◽  
Ma Wei ◽  
Li Bin ◽  
Wang Chengyong
Keyword(s):  
High Speed ◽  
High Speed Milling

Effects of Cutting Parameters on Residual Stresses in High-Speed Milling of Ti-17

2013 ◽  
Vol 834-836 ◽  
pp. 861-865 ◽  
Author(s):  
Yong Shou Liang ◽  
Jun Xue Ren ◽  
Yuan Feng Luo ◽  
Ding Hua Zhang
Keyword(s):  
Experimental Study ◽  
Residual Stresses ◽  
High Speed ◽  
Experimental Parameter ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Single Factor ◽  
Cutting Depth ◽  
High Speed Milling ◽  
Parameter Ranges

An experimental study was conducted to determine cutting parameters of high-speed milling of Ti-17 according to their effects on residual stresses. First, three groups of single factor experiments were carried out to reveal the effects of cutting parameters on residual stresses. Then sensitivity models were established to evaluate the influence degrees of cutting parameters on residual stresses. After that, three criteria were proposed to determine cutting parameters from experimental parameter ranges. In the experiments, the cutting parameter ranges are recommended as [371.8, 406.8] m/min, [0.363, 0.412] mm and [0, 0.018] mm/z for cutting speed, cutting depth and feed per tooth, respectively.

Discrete Element Simulation of the Stress Wave in High Speed Milling

2017 ◽  
Author(s):  
Yifei Jiang ◽  
Jun Zhang ◽  
Yong He ◽  
Hongguang Liu ◽  
Afaque Rafique Memon ◽  
...  
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Discrete Element ◽  
Rake Angle ◽  
Stress Waves ◽  
High Speed Milling ◽  
Element Simulation ◽  
Chip Size ◽  
Distribution Of Stress

As cutting tool penetrates into workpiece, stress waves is induced and propagates in the workpiece. This paper aims to propose a two-dimensional discrete element method to analyze the stress waves effects during high speed milling. The dependence of the stress waves propagation characteristics on rake angle and cutting speed was studied. The simulation results show that the energy distribution of stress waves is more concentrated near the tool tip as the rake angle or the cutting speed increases. In addition, the density of initial cracks in the workpiece near the cutting tool increases when the cutting speed is higher. The high speed milling experiments indicate that the chip size decreases as the cutting speed increases, which is just qualitatively consistent with the simulation.

Sign in / Sign up

Export Citation Format

Share Document