Reliability of Large-Eddy Simulation of Nonpremixed Turbulent Flames: Scalar Dissipation Rate Modeling and 3D-Boundary Conditions

2008 ◽  
pp. 227-237
Author(s):  
L. Vervisch ◽  
G. Lodato ◽  
P. Domingo
Keyword(s):  
Large Eddy Simulation ◽  
Boundary Conditions ◽  
Dissipation Rate ◽  
Turbulent Flames ◽  
Scalar Dissipation ◽  
Scalar Dissipation Rate ◽  
Eddy Simulation ◽  
Large Eddy

scholarly journals A-Priori Validation of Scalar Dissipation Rate Models for Turbulent Non-Premixed Flames

2020 ◽  
Author(s):  
M. P. Sitte ◽  
C. Turquand d’Auzay ◽  
A. Giusti ◽  
E. Mastorakos ◽  
N. Chakraborty
Keyword(s):  
Dissipation Rate ◽  
A Priori ◽  
Turbulent Flames ◽  
Large Eddy Simulations ◽  
Moment Closure ◽  
Scalar Dissipation ◽  
Combustion Model ◽  
Scalar Dissipation Rate ◽  
Jet Flame ◽  
Large Eddy

Abstract The modelling of scalar dissipation rate in conditional methods for large-eddy simulations is investigated based on a priori direct numerical simulation analysis using a dataset representing an igniting non-premixed planar jet flame. The main objective is to provide a comprehensive assessment of models typically used for large-eddy simulations of non-premixed turbulent flames with the Conditional Moment Closure combustion model. The linear relaxation model gives a good estimate of the Favre-filtered scalar dissipation rate throughout the ignition with a value of the related constant close to the one deduced from theoretical arguments. Such value of the constant is one order of magnitude higher than typical values used in Reynolds-averaged approaches. The amplitude mapping closure model provides a satisfactory estimate of the conditionally filtered scalar dissipation rate even in flows characterised by shear driven turbulence and strong density variation.

scholarly journals Large Eddy Simulations of a turbulent premixed swirl flame using an algebraic scalar dissipation rate closure

2015 ◽  
Vol 162 (9) ◽  
pp. 3180-3196 ◽  
Author(s):  
David Butz ◽  
Yuan Gao ◽  
Andreas M. Kempf ◽  
Nilanjan Chakraborty
Keyword(s):  
Dissipation Rate ◽  
Large Eddy Simulations ◽  
Scalar Dissipation ◽  
Scalar Dissipation Rate ◽  
Large Eddy ◽  
Swirl Flame ◽  
Turbulent Premixed

A Method of Measuring Turbulent Flow Structures With Particle Image Velocimetry and Incorporating Into Boundary Conditions of Large Eddy Simulations

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Puxuan Li ◽  
Steve J. Eckels ◽  
Garrett W. Mann ◽  
Ning Zhang
Keyword(s):  
Particle Image Velocimetry ◽  
Large Eddy Simulation ◽  
Boundary Conditions ◽  
Particle Image ◽  
Advantages And Disadvantages ◽  
Eddy Simulation ◽  
Piv Measurement ◽  
Image Velocimetry ◽  
Large Eddy ◽  
Inlet Conditions

The setup of inlet conditions for a large eddy simulation (LES) is a complex and important problem. Normally, there are two methods to generate the inlet conditions for LES, i.e., synthesized turbulence methods and precursor simulation methods. This study presents a new method for determining inlet boundary conditions of LES using particle image velocimetry (PIV). LES shows sensitivity to inlet boundary conditions in the developing region, and this effect can even extend into the fully developed region of the flow. Two kinds of boundary conditions generated from PIV data, i.e., steady spatial distributed inlet (SSDI) and unsteady spatial distributed inlet (USDI), are studied. PIV provides valuable field measurement, but special care is needed to estimate turbulent kinetic energy and turbulent dissipation rate for SSDI. Correlation coefficients are used to analyze the autocorrelation of the PIV data. Different boundary conditions have different influences on LES, and their advantages and disadvantages for turbulence prediction and static pressure prediction are discussed in the paper. Two kinds of LES with different subgrid turbulence models are evaluated: namely dynamic Smagorinsky–Lilly model (Lilly model) and wall modeled large eddy simulation (WMLES model). The performances of these models for flow prediction in a square duct are presented. Furthermore, the LES results are compared with PIV measurement results and Reynolds-stress model (RSM) results at a downstream location for validation.

scholarly journals Experimental study of wall boundary conditions for large-eddy simulation

2001 ◽  
Vol 446 ◽  
pp. 309-320 ◽  
Author(s):  
IVAN MARUSIC ◽  
GARY J. KUNKEL ◽  
FERNANDO PORTÉ-AGEL
Keyword(s):  
Boundary Layer ◽  
Boundary Condition ◽  
Shear Stress ◽  
Wall Shear Stress ◽  
Large Eddy Simulation ◽  
Boundary Conditions ◽  
Streamwise Velocity ◽  
New Model ◽  
Eddy Simulation ◽  
Large Eddy

An experimental investigation was conducted to study the wall boundary condition for large-eddy simulation (LES) of a turbulent boundary layer at Rθ = 3500. Most boundary condition formulations for LES require the specification of the instantaneous filtered wall shear stress field based upon the filtered velocity field at the closest grid point above the wall. Three conventional boundary conditions are tested using simultaneously obtained filtered wall shear stress and streamwise and wall-normal velocities, at locations nominally within the log region of the flow. This was done using arrays of hot-film sensors and X-wire probes. The results indicate that models based on streamwise velocity perform better than those using the wall-normal velocity, but overall significant discrepancies were found for all three models. A new model is proposed which gives better agreement with the shear stress measured at the wall. The new model is also based on the streamwise velocity but is formulated so as to be consistent with ‘outer-flow’ scaling similarity of the streamwise velocity spectra. It is therefore expected to be more generally applicable over a larger range of Reynolds numbers at any first-grid position within the log region of the boundary layer.

Sign in / Sign up

Export Citation Format

Share Document