Soaking Water Composition

Author(s):  
Luca Serventi
Keyword(s):  
1988 ◽  
Vol 20 (3) ◽  
pp. 133-140 ◽  
Author(s):  
Annika Lindblad-Påsse

A number of groundwater heat pump systems have been investigated to determine the extent of problems caused by the chemistry of the groundwater used. The main purpose was to investigate sites using iron rich groundwater. Fifteen facilities were studied regularly for three years. Ten of these facilities had some kind of problem caused by iron precipitation. Four of the sites were rebuilt because of severe plugging due to iron sludge in wells, pumps and pipes. In all facilities with severe problems, iron bacteria were found. Low redox potential, indicated by hydrogen sulphide in the groundwater, seems to protect from iron bacteria. In some of the systems using groundwater with H2S the problems were corrosion and sludge formation caused by sulphur oxidizing bacteria. Rapid clogging was caused by aeration of the groundwater due to improper design of the system. Knowledge of the water composition, design of the systems to minimize aeration, and control of clogging turned out to be important factors to maintain operation safety.


2017 ◽  
Vol 24 (1) ◽  
pp. 41-51
Author(s):  
Agata Rosińska

Abstract The aim of the research was to compare selected coagulants efficiency in indicator and chosen dioxin-like PCB removal from surface water. As coagulants, there were used aluminium sulfate and 5 hydrolyzed polyaluminium chlorides, with trade names: PAX-XL1, PAX-XL10, PAX-XL19, PAX-XL60, PAX-XL69. For the research, surface water was used, collected from dam reservoir. The water composition was modified with standard mixtures PCB MIX24 and MIX13, in order to obtain concentration of each congener equal to 300 ng/dm3. The PCB MIX24 mixture was composed of indicator congeners solution: 28, 52, 101, 118, 138, 153, and 180, whereas the MIX13 mixture - solution of three dioxin-like PCB 77, PCB 126, and PCB 169. It was demonstrated that the application of aluminium sulfate allowed for reaching better effects for purifying water of PCB, than with the usage of pre-hydrolyzed salts, polyaluminium chlorides. Out of the studied coagulants, the best effects for indicator PCB removal were obtained with the application of aluminium sulfate, total PCB concentration was decreased by 65%. The highest efficiency for indicator congeners removal (90%) was obtained for PCB 138 and 153. After the application of hydrolyzed polyaluminium chlorides PAX-XL1, PAX-XL10 decrease in higher chlorinated PCB concentration was obtained, in the range of 23 to 74%. Selectivity of chosen PCB congener removal, depending on applied coagulant, was demonstrated; with the usage of aluminium sulfate, removal of heptachlorobiphenyl PCB 180 at the level of 34% was obtained, whereas with the application of PAX-XL1 and PAX-XL10 higher reduction efficiency for this congener was obtained, i.e. 83 and 74% respectively. For dioxin-like PCB, after application of aluminium sulfate, total concentration reduction by 74% was obtained, efficiency of this congeners removal amounted to from 54 (PCB 77) up to 72% (PCB 126), similar results were obtained after the usage of PAX-XL1. The lowest PCB removal from water rate was stated for coagulants PAX-XL60 and PAX-XL69.


2011 ◽  
Author(s):  
Robin Gupta ◽  
Griffin Griffin Smith ◽  
Lu Hu ◽  
Thomas Willingham ◽  
Mauro Lo Cascio ◽  
...  

2009 ◽  
Vol 101 (1) ◽  
pp. 88
Author(s):  
Ulrike Schacht ◽  
Steffen Kutterolf ◽  
Oliver Bartdorff ◽  
Emelina Corrales Cordero

2011 ◽  
Vol 38 (5) ◽  
pp. 662-669 ◽  
Author(s):  
G. Baldassare ◽  
P. Pagliarulo ◽  
L. E. Zuffianò
Keyword(s):  

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 365
Author(s):  
Jose Luis Cerrillo ◽  
Antonio Eduardo Palomares

The presence of bromate in water sources generates environmental concern due to its toxicity for humans. Diverse technologies, like membranes, ion exchange, chemical reduction, etc., can be employed to treat bromate-polluted water but they produce waste that must be treated. An alternative to these technologies can be the catalytic reduction of bromate to bromide using hydrogen as a reducing agent. In this review, we analyze the research published about this catalytic technology. Specifically, we summarize and discuss about the state of knowledge related to (1) the different metals used as catalysts for the reaction; (2) the influence of the support on the catalytic activity; (3) the characterization of the catalysts; (4) the reaction mechanisms; and (5) the influence of the water composition in the catalytic activity and in the catalyst stability. Based on published papers, we analyze the strength and weaknesses of this technique and the possibilities of using this reaction for the treatment of bromate-polluted water as a sustainable process.


Sign in / Sign up

Export Citation Format

Share Document