Use of Waste Glass Powder as Partial Replacement of Cement Mortar: Environmental Effects

2021 ◽  
pp. 291-296
Author(s):  
Abderrezak Khellou ◽  
Laid Mechri ◽  
Sofiane Saggaï
Keyword(s):  
Environmental Effects ◽  
Glass Powder ◽  
Cement Mortar ◽  
Waste Glass ◽  
Partial Replacement ◽  
Waste Glass Powder

scholarly journals Thermophysical Properties of Cement Mortar Containing Waste Glass Powder

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 488
Author(s):  
Oumaima Nasry ◽  
Abderrahim Samaouali ◽  
Sara Belarouf ◽  
Abdelkrim Moufakkir ◽  
Hanane Sghiouri El Idrissi ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Specific Heat ◽  
Thermophysical Properties ◽  
Glass Powder ◽  
Cement Mortar ◽  
Soda Lime ◽  
Waste Glass ◽  
Soda Lime Glass ◽  
Volumetric Specific Heat ◽  
Waste Glass Powder

This study aims to provide a thermophysical characterization of a new economical and green mortar. This material is characterized by partially replacing the cement with recycled soda lime glass. The cement was partially substituted (10, 20, 30, 40, 50 and 60% in weight) by glass powder with a water/cement ratio of 0.4. The glass powder and four of the seven samples were analyzed using a scanning electron microscope (SEM). The thermophysical properties, such as thermal conductivity and volumetric specific heat, were experimentally measured in both dry and wet (water saturated) states. These properties were determined as a function of the glass powder percentage by using a CT-Meter at different temperatures (20 °C, 30 °C, 40 °C and 50 °C) in a temperature-controlled box. The results show that the thermophysical parameters decreased linearly when 60% glass powder was added to cement mortar: 37% for thermal conductivity, 18% for volumetric specific heat and 22% for thermal diffusivity. The density of the mortar also decreased by about 11% in dry state and 5% in wet state. The use of waste glass powder as a cement replacement affects the thermophysical properties of cement mortar due to its porosity as compared with the control mortar. The results indicate that thermal conductivity and volumetric specific heat increases with temperature increase and/or the substitution rate decrease. Therefore, the addition of waste glass powder can significantly affect the thermophysical properties of ordinary cement mortar.

Studies on Exciting the Activity of Waste Glass Powder by Hydrothermal Activation

2013 ◽  
Vol 871 ◽  
pp. 171-178
Author(s):  
Qing Qiu Kong ◽  
Guo Jun Ke ◽  
Dan Wang
Keyword(s):  
Compressive Strength ◽  
Hydrothermal Treatment ◽  
Glass Powder ◽  
Cement Mortar ◽  
Waste Glass ◽  
Early Age ◽  
Cement Replacement ◽  
Waste Glass Powder ◽  
Temperature And Pressure ◽  
Optimal Strength

The effect of hydrothermal activation indifferent temperature and pressure conditions on the pozzolanic activity of waste glass powder was discussed. The waste glass powder was treated at 108°C, 0.15MPa, 116°C, 0.18MPa and 121°C, 0.2MPa for 2h in an autoclave respectively after milling to 4215cm2/g. Mortar was made with untreated and hydrothermal activated waste glass power replacement of cement at 20% respectively, then tested for compressive strength at 3, 7, 14 , 28 and 90 days. Results showed that compressive strength of cement mortar had varying degrees of decline when replacing cement with untreated waste glass powder, comparing to the control one. Decline amplitude was large at early age and small at late age. Activity of waste glass powder was significantly improved after hydrothermal treatment. Compressive strength of mortar improved as temperature and pressure elevated, obtaining optimal strength at 121°C, 0.2MPa. Compressive strength of mortar with hydrothermal activated glass powder was higher than that with untreated glass powder at all age with 20% cement replacement. Compressive strength increased 5.3% ~ 13.6% at 3 d, 6.8%~9.7% at 28 d, 9.7% ~ 17.7% at 90 d. The essence of hydrothermal activation was the corrosion of water in the glass.

scholarly journals Mechanical Properties of Mortars Containing Waste Glass Powder

2019 ◽  
Vol 50 (1) ◽  
pp. 30-34 ◽  
Author(s):  
Elżbieta Horszczaruk ◽  
Piotr Brzozowski
Keyword(s):  
Construction Industry ◽  
Co2 Emission ◽  
Glass Powder ◽  
Waste Glass ◽  
Partial Substitution ◽  
Partial Replacement ◽  
Glass Cullet ◽  
Glass Waste ◽  
Waste Glass Powder ◽  
Creative Construction

The utilization of solid waste materials or industrial waste as partial substitution of cement is growing in construction industry all around world. Less cement consumption causes consequently reduction in CO2 emission into the atmosphere and reduction in energy consumption. This paper examines the possibility of using finely ground waste glass as a partial replacement for cement and as a sealing admixture. Glass powder used in the research was prepared from the glass waste obtained from a local recycling company. Glass cullet made of brown glass, which after rinsing to remove sugars and other impurities, was dried and ground to a fraction below 125 μm.This paper is the revised version of the paper that has been published in the Proceedings of the Creative Construction Conference 2018 (Horszczaruk and Brzozowski, 2018).

scholarly journals Effect of Partial Replacement of Crushed Stone Dust Filler with Waste Glass Powder in Hot Mix Asphalt Concrete Production

2020 ◽  
Author(s):  
Destaw Kifile ◽  
Emer Quezon ◽  
Abel Tesfaye
Keyword(s):  
Glass Powder ◽  
Hot Mix Asphalt ◽  
Road Construction ◽  
Waste Glass ◽  
Crushed Stone ◽  
Partial Replacement ◽  
Waste Glass Powder ◽  
Stone Dust ◽  
Concrete Production ◽  
Bitumen Content

The use of waste recycled materials in road construction nowadays considered a positive means of providing improved pavement performance. This research focused on evaluating the effect of waste glass powder as a partial replacement of crushed stone dust filler in hot mix asphalt. Three hot mix asphalt samples produced using crushed stone dust of 5%, 6.5%, and 8% as mineral filler with five different bitumen content of 4%, 4.5%, 5%, 5.5%, and 6%, respectively. From the preliminary series tests of asphalt contents, a 6.5% crushed stone dust filler selected, providing the highest stability of waste glass powder. The content of crushed stone dust filler replaced with a rate of 0%, 25%, 50%, 75%, and 100% to test Marshal stability to obtain the Optimum bitumen content and Optimum filler content. Results indicated at 75% replacement of crushed stone dust with waste glass powder at 5.10% bitumen content, 12.0kN Marshall stability value, 2.84mm Flow value, 4.0% Air voids, 72.3% VFB, and 2.360g/cm3 Bulk density. Hence, the mixture of 75% waste glass powder by weight of crushed stone dust filler meets the minimum requirements of the Ethiopian Road Authority and Asphalt Institute Specifications.

The Research on the Strength of Cement Mortar with Different Particle Size of Waste Glass Powder

2014 ◽  
Vol 1082 ◽  
pp. 265-269 ◽  
Author(s):  
Guo Jun Ke ◽  
Yan Chao Wang ◽  
Pin Yu Zou ◽  
Dai Nian Zeng
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Glass Powder ◽  
Cement Mortar ◽  
Waste Glass ◽  
Optimum Size ◽  
Best Value ◽  
Waste Glass Powder ◽  
Baseline Group ◽  
Mixed Water

To study the strength of cement mortar with different particle size of waste glass powder, grinding and screening the colorless waste glasses to 38-53,53-75,75-150,150-300,300-600μm, and as supplementary cement materials replacing the cement of cement mortar at 5,10,15,20,25,30%, respectively. Meanwhile divide the experiment into two parts:containing water reducer or not and add fly ash as comparison at the same time, measuring the flexural and compressive strength of cement mortar for 28 days. It is concluded that the flexural and compressive strength of cement mortar are decreased when mix with water reducer with maintaining the dosage of water;The optimum size and amount of waste glass powder in the cement mortar keep the same whether it is mixed water reducer or not; The flexural and compressive strength for 28days of the cement mortar reach the best value and differ with the baseline group very few whether it's mixed water reducer or not.

scholarly journals Development of Environment-Friendly Concrete through Partial Addition of Waste Glass Powder (WGP) as Cement Replacement

2020 ◽  
Vol 6 (12) ◽  
pp. 2332-2343
Author(s):  
Fasih Ahmed Khan ◽  
Khan Shahzada ◽  
Qazi Sami Ullah ◽  
Muhammad Fahim ◽  
Sajjad Wali Khan ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Glass Powder ◽  
Waste Glass ◽  
Modulus Of Rupture ◽  
Partial Replacement ◽  
Supplementary Cementitious Material ◽  
Beam Elements ◽  
Pozzolanic Material ◽  
Waste Glass Powder ◽  
Study Results

This paper presents the study carried out on the utilization of Waste Glass Powder (WGP) as supplementary cementitious material in concrete. The evaluation of the influence of WGP on the mechanical properties of concrete was carried out by casting and testing of concrete samples as per ASTM standards (cylinders and beam elements). The control samples were designed to represent field conditions with a target compressive strength of 20,000 kPa. The Portland cement in concrete was substituted with WGP in proportions of 0%-35% by weight, in increments of 5%. Two curing domains were adopted in the preparation of the test samples to evaluate the effect of pozzolanic material wherein the tested samples were cured for 28, 56, and 84 days. The study results indicated a reduction in compressive strength of concrete up to 10% with partial replacement of cement with 25% of WGP when standard curing of 28 days was adopted. Furthermore, with the same replacement proportion and prolonged curing for 84 days, the gap in strength reduction was reduced by 5%. However, a significant decrease in workability was noted between the control concrete samples and glass powder infused concrete. Furthermore, the Waste Glass Powder Concrete (WGPC) exhibited an improved flexural strength with the modulus of rupture for WGPC being 2% higher than control concrete at the age of 84 days. Based on the results of this study it was concluded that 25% replacement of cement with WGP provides an optimum replacement ratio. Doi: 10.28991/cej-2020-03091620 Full Text: PDF

Sign in / Sign up

Export Citation Format

Share Document