Externally Bonded CFRP Strengthened RC Slabs, Four years of External Environment Exposure and Evaluation of the Load Carrying Capacity

2021 ◽  
pp. 659-670
Author(s):  
Matteo Breveglieri ◽  
Christoph Czaderski
Keyword(s):  
Carrying Capacity ◽  
External Environment ◽  
Load Carrying Capacity ◽  
Environment Exposure ◽  
Load Carrying ◽  
Externally Bonded ◽  
Rc Slabs

Flexural strengthening of pre-cracked RC slabs with prestressed NSM CFRP laminates and evaluation of strain loss

2021 ◽  
pp. 136943322110105
Author(s):  
M.R. Mostakhdemin Hosseini ◽  
Salvador J.E. Dias ◽  
Joaquim A.O. Barros
Keyword(s):  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Limit States ◽  
Transfer Length ◽  
Rc Structures ◽  
Cracked Concrete ◽  
Flexural Strengthening ◽  
Cfrp Laminates ◽  
Load Carrying ◽  
Rc Slabs

The strengthening intervention of RC structures often involves already cracked concrete. To evaluate the effect of the level of damage prior to the strengthening (pre-cracks) on the behavior of the flexurally strengthened RC slabs with prestressed NSM CFRP laminates, an experimental research was carried out. Two pre-cracking levels of damage were analyzed and, for each one, three levels of prestress were tested (0%, 20% and 40%). The obtained results showed that the strengthening of damaged RC slabs with prestressed NSM CFRP laminates results in a significant increase on the load carrying capacity at serviceability limit states. Pre-cracked RC slabs strengthened with prestressed NSM CFRP laminates presented a load carrying capacity almost similar to the corresponding uncracked strengthened slabs. To determine the effective prestress level in CFRP laminates, the variation of strain over the length of the CFRP and over time was experimentally recorded. The prestress transfer length was also evaluated. The experimental results revealed that the transfer length of CFRP laminates was less than 150 mm, and the maximum value of strain loss out of transfer length (around 14%) was measured close to the cracked section of the damaged RC slabs. Significant part of strain loss in CFRP laminates occurred during 24 h after releasing the prestress load.

Load-Carrying Capacities of Fully Clamped RC Slab Accompanying Compressive-Tensile Membrane Actions: A Theoretical Approach

2020 ◽  
Vol 20 (08) ◽  
pp. 2050094
Author(s):  
Wanxiang Chen ◽  
Lisheng Luo ◽  
Zhikun Guo ◽  
Yingjie Wang
Keyword(s):  
Bearing Capacity ◽  
Carrying Capacity ◽  
Flexural Rigidity ◽  
Load Carrying Capacity ◽  
Membrane Action ◽  
Yield Line ◽  
Load Carrying ◽  
Membrane Effects ◽  
Rc Slab ◽  
Rc Slabs

Fully clamped reinforced concrete (RC) slab is a common structural component possessing better load-carrying capacity over simply supported slab. Currently, typical yield line theory is a popular approach to estimate the bearing capacity of fully clamped RC slab, although it would greatly underestimate the actual ultimate resistance. This paper is devoted to enriching the knowledge of membrane action and its contribution to the load-carrying capacity of the clamped slab. The resistance trajectory of fully clamped RC slab from loading to failure undergoes three phases: the ascending branch raised by outward movement prevention, the descending branch due to crushed concrete and the re-ascending branch caused by reinforcement strain. Applied load–deflection curves of RC slab accompanying compressive-membrane actions are achieved according to the bending theory of normal cross-section. The reserve capacities accompanying tensile-membrane actions in the condition of large deformations are further derived. The whole load–deflection curves that considered compressive-tensile membrane effects are finally presented, where the mid-span displacements are revised by the deflection equations and the softening coefficient of flexural rigidity. It is indicated that the load–deflection relationships of fully clamped RC slabs can be reasonably depicted by taking compressive-tensile membrane effects into account, which are fairly different from yield line approaches. Comparative analysis shows that analytical results are in good agreement with experimental data reported by Park et al. and illustrates that the proposed model is capable of predicting the bearing capacity of fully clamped RC slab with very good accuracy.

Effect of CFRP Thickness on Load-Carrying Capacities and Failure Modes of Strengthened RC Beams

2011 ◽  
Vol 255-260 ◽  
pp. 109-112
Author(s):  
Guo Wen Yao ◽  
Mao Sheng Li ◽  
Shi Ya Li
Keyword(s):  
Carrying Capacity ◽  
Failure Modes ◽  
Mechanical Analysis ◽  
Load Carrying Capacity ◽  
Rc Beams ◽  
Bending Load ◽  
Load Carrying ◽  
Carbon Fiber Laminate ◽  
Externally Bonded ◽  
Ultimate Loading

The effect of thickness of externally bonded carbon fiber laminate (CFRP) on load-carrying capacity and failure modes was analyzed for the strengthened reinforced concrete (RC) beams under bending load. According to the balance equations of applied force and moment, the relation was obtained between ultimate loading of strengthened beam and thickness of CFRP, and the failure modes were predicted for the CFRP strengthened beams. The load-carrying capacity of strengthened RC beam is higher with thicker externally bonded CFRP until it reaches the ultimate loading. The mechanical analysis is in good agreement with the three-point bending experiments performed on CFRP strengthened RC beams.

Axial behaviour of HSS tubular sections strengthened by CFRP strips: an experimental investigation

2012 ◽  
Vol 19 (2) ◽  
pp. 159-168 ◽  
Author(s):  
Muthukamatchi Chelliah Sundarraja ◽  
Sandrasekaran Sivasankar
Keyword(s):  
Carrying Capacity ◽  
Failure Modes ◽  
Load Carrying Capacity ◽  
Structural Behaviour ◽  
Steel Tubes ◽  
Strain Behaviour ◽  
Load Carrying ◽  
Externally Bonded ◽  
Fibre Reinforced Polymer ◽  
Tubular Sections

AbstractThe main objective of this investigation is to assess the feasibility of strengthening square hollow steel tubular sections subjected to compression and to develop or predict the suitable wrapping scheme of fibre reinforced polymer (FRP) to enhance the structural behaviour of it. For this study, compact mild steel tubes were used with the main variable being FRP characteristics. Carbon fibre has been considered and used as strips with several other parameters such as the number of layers, width and spacing of strips, the sectional area of strips, and wrapping scheme. Experiments were undertaken until column failure to fully understand the influence of FRP characteristics on the compressive behaviour of square hollow steel tubes including their failure modes, stress-strain behaviour, enhancement in load carrying capacity and effect of distribution of CFRP layers. The behaviour of externally bonded hollow steel tubular sections was compared with one another and also with the control specimen. From the test results, it was found that CFRP strengthening significantly increases the load carrying capacity and ductility of the hollow steel tubular members further.

scholarly journals Degradation of the EBR-CFRP strengthening system applied to reinforced concrete beams exposed to weathering

2021 ◽  
Vol 14 (2) ◽  
Author(s):  
Gláucia Maria Dalfré ◽  
Guilherme Aris Parsekian ◽  
Douglas da Costa Ferreira
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Natural Aging ◽  
Outdoor Exposure ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Externally Bonded ◽  
Cfrp Composite

Abstract Little is known about the behavior and durability of strengthening systems applied on concrete substrata and the possible loss of performance due to the degradation of the intervening materials by the structure’s natural aging process and exposure of the externally strengthened elements to aggressive environments. In this context, the present work presents an experimental analysis of the behavior of reinforced concrete beams strengthened with Carbon Fiber Reinforced Polymer (CFRP), applied according to the Externally Bonded Reinforcement (EBR) technique, maintained in a laboratory environment (indoor and protected) or exposed to weathering (outdoor exposure). In addition, specimens of the intervenient materials were also molded and exposed to the same environmental conditions as the beams. The results indicate that weather-exposed epoxy adhesives present reductions up to 70% in their mechanical properties after exposure, while the CFRP composite properties remain similar. It was also found that the strengthening system provided 50% and 28% increments in the load-carrying capacity and stiffness of the elements, respectively. However, the tests conducted after 6 months of weathering exposure showed a 10% reduction in the load-carrying capacity of the strengthened elements.

Sign in / Sign up

Export Citation Format

Share Document