Experimental Investigation on Adhesive Bonded Fold Tubes Under Quasi-Static Loading

2021 ◽  
pp. 657-666
Author(s):  
M. Nalla Mohamed ◽  
R. Sivaprasad
Keyword(s):  
Experimental Investigation ◽  
Static Loading

Effect of the ageing on the dissipative properties of getinacks subjected to repeated static loading

2014 ◽  
Vol 11 (6) ◽  
pp. 589-596
Author(s):  
Valesyan Shant
Keyword(s):  
Experimental Data ◽  
Experimental Investigation ◽  
Temperature Field ◽  
Energy Dissipation ◽  
Hysteresis Loop ◽  
Static Loading ◽  
Applied Load ◽  
Effect Of Temperature ◽  
Loading And Unloading

The effect of ageing on the dissipative properties of getinacks subjected to repeated static loading has been investigated. Specimens were tested at the age of 1, 4, and 8 years. The approximation of experimental data is done, and the energy of dissipation is calculated. Based on the investigation of getinacks manufactured by the technology of regulated thermo-pressing, this technology can be recommended for the manufacturing of appropriate products.The results of experimental investigation of the effect of temperature field on the dissipative properties of layered getinacks widely applicable in electrical manufacturing, electronics and microelectronics are considered in this paper. The approximation of the experimentally obtained dependences between σ and ε for the loading (→) and unloading (←) parts of the hysteresis loop are calculated and plotted. The factor of energy dissipation is defined. Estimated that the temperature field affects the dissipative properties of the layered getinacks and that effect is depending on the value of applied load cyclically acting on the material.

Experimental Investigation of Energy Absorption of ‎Partially Wrapped Thin-Walled ‎Aluminium-Glass/Epoxy Tube Subjected to Quasi-Static Loading

2017 ◽  
Vol 904 ◽  
pp. 61-67
Author(s):  
Tahir Abbas ◽  
Hamdan H. Ya ◽  
Mohamad Zaki Abdullah
Keyword(s):  
Experimental Investigation ◽  
Energy Absorption ◽  
Fiber Orientation ◽  
Static Loading ◽  
Failure Modes ◽  
Testing Machine ◽  
Filament Winding ◽  
Universal Testing ◽  
Thin Walled ◽  
Filament Winding Process

This paper describes the failure modes and energy absorption capability of partially wrapped aluminium-glass/epoxy tubes, subjected to quasi-static loading. ‎These tubes are used in aircraft and automobiles applications. Aluminium tubes were partially wrapped with 4, 6 and 8 glass/epoxy layers, using filament winding process. The 90◦ fiber orientation was used for glass/epoxy layers. Quasi-static loading of partially wrapped tubes was carried out at 5mm/min speed, using the universal ‎testing machine. The experimental results revealed that partially wrapped aluminium tubes are 42.54%, 47.77% and 28.91% more ‎efficient in energy absorption as compared to the simple aluminium tubes. Furthermore, the effect of glass/epoxy layers on ‎failure modes has also been described.

Experimental investigation on the behavior of fine-grained soils containing waste rubber tires under repeated and static loading using direct shear apparatus

2019 ◽  
Vol 223 ◽  
pp. 106-119 ◽  
Author(s):  
Mohammad Karamad Tabrizi ◽  
Saeed Abrishami ◽  
Ehsan Seyedi Hosseininia ◽  
Sohrab Sharifi ◽  
Saeid Ghorbani
Keyword(s):  
Experimental Investigation ◽  
Static Loading ◽  
Direct Shear ◽  
Fine Grained ◽  
Waste Rubber ◽  
Direct Shear Apparatus

Experimental Investigation of In-Plane Mechanical Performance of Carbon/Glass Hybrid Woven Composite

2014 ◽  
Vol 697 ◽  
pp. 132-135
Author(s):  
Jia Hai Lu ◽  
Ping Zhu ◽  
Qing Hui Ji ◽  
Zhang Cheng
Keyword(s):  
Experimental Investigation ◽  
Mechanical Behavior ◽  
Static Loading ◽  
Mechanical Performance ◽  
Woven Composites ◽  
Woven Composite ◽  
Compressive Behavior ◽  
Engineering Applications ◽  
Vacuum Infusion ◽  
Effective Use

Woven composites have been increasingly employed in engineering applications. For effective use of woven composites in engineering applications, it is essential to fully understand the mechanical behavior. In the present study, both tensile and compressive behavior of a carbon/glass hybrid woven composite manufactured by vacuum infusion process was experimentally investigated under in-plane quasi-static loading. The experiments were performed at both the axial and off-axial directions. The results indicated that the in-plane mechanical performance of the studied composite was highly directional dependent and tension/compression asymmetric.

An Experimental Investigation into the Strainburst Process Under Quasi-static Loading

2020 ◽  
Vol 53 (12) ◽  
pp. 5617-5629
Author(s):  
Fuqiang Gao ◽  
Hongpu Kang ◽  
Lei Yang
Keyword(s):  
Experimental Investigation ◽  
Static Loading

Experimental investigation of the deformation of thin plates under static loading and interaction with a shock

1983 ◽  
Vol 19 (10) ◽  
pp. 906-911
Author(s):  
I. I. Anik'ev ◽  
M. I. Mikhailova ◽  
A. S. Spisovskii ◽  
A. L. Timofeev
Keyword(s):  
Experimental Investigation ◽  
Static Loading ◽  
Thin Plates

Moment-rotation behavior of semi-rigid web cleat connections

2020 ◽  
Vol 6 (3) ◽  
pp. 110
Author(s):  
Merve Sağıroğlu ◽  
Mahyar Maali ◽  
Abdulkadir Cüneyt Aydın ◽  
Mahmut Kılıç
Keyword(s):  
Experimental Investigation ◽  
Static Loading ◽  
Bolted Connections ◽  
Rotation Capacity ◽  
Eurocode 3 ◽  
Moment Resisting ◽  
Resistance Moment ◽  
Rigid Connection ◽  
The Moment ◽  
Standard Profile

The behavior of beam-column semi-rigid connection plays an important role in the response of a steel moment resisting, stiffness and rotation capacity framed structure, especially under static loading conditions. In this study, the moment-rotation characteristics of semi-rigid bolted connections using web cleat connections with IPE standard profile is discussed, based on the experimental investigation. The study revealed that the moment resistance of beam-column semi-rigid connection is improved by increasing the height of the beam to the height of web cleat joint (H), and the increasing thickness of web and flange in web cleat joints. The aim was to provide necessary data to improve the Eurocode 3 and efficiently use residue IPE standard profiles, rather than send them back to the consumption cycle. While the resistance moment increased with an increase in H from Hmin to Hmax.

Sign in / Sign up

Export Citation Format

Share Document