High-temperature reaction in titanium alloy-ceramic fiber composite materials

1993 ◽  
Vol 35 (11) ◽  
pp. 643-648
Author(s):  
V. I. Bakarinov ◽  
V. N. Meshcheryakov
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Composite Materials ◽  
Fiber Composite ◽  
Ceramic Fiber ◽  
Temperature Reaction ◽  
High Temperature Reaction ◽  
Fiber Composite Materials

Wood-Glass Fiber Composite Materials in Structural Elements of Tram Tracks

2019 ◽  
Vol 777 (12) ◽  
pp. 73-77
Author(s):  
B.A. BONDAREV ◽  
◽  
T.N. STORODUBTSEVA ◽  
D.A. KOPALIN ◽  
S.V. KOSTIN ◽  
...  
Keyword(s):  
Composite Materials ◽  
Glass Fiber ◽  
Fiber Composite ◽  
Structural Elements ◽  
Glass Fiber Composite ◽  
Fiber Composite Materials

Study of high-pressure air jet controlled compression ignition with compound thermodynamic cycle for combustion and emission formation process

2020 ◽  
pp. 146808742096933
Author(s):  
Xiangyu Meng ◽  
Sicheng Liu ◽  
Jingchen Cui ◽  
Jiangping Tian ◽  
Wuqiang Long ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Low Temperature ◽  
Formation Process ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Compression Ignition ◽  
Temperature Reaction ◽  
Air Jet ◽  
High Temperature Reaction

A novel method called high-pressure air (HPA) jet controlled compression ignition (JCCI) based on the compound thermodynamic cycle was investigated in this work. The combustion process of premixed mixture can be controlled flexibly by the high-pressure air jet compression, and it characterizes the intensified low-temperature reaction and two-stage high-temperature reaction. The three-dimensional (3D) computational fluid dynamics (CFD) numerical simulation was employed to study the emission formation process and mechanism, and the effects of high-pressure air jet temperature and duration on emissions were also investigated. The simulation results showed that the NOx formation is mainly affected by the first-stage high-temperature reaction due to the higher reaction temperature. Overall, this combustion mode can obtain ultra-low NOx emission. The second-stage high-temperature reaction plays an important role in the CO and THC formation caused by the mixing effect of the high-pressure air and original in-cylinder mixture. The increasing air jet temperature leads to a larger high-temperature in-cylinder region and more fuel in the first-stage reaction, and therefore resulting in higher NOx emission. However, the increasing air jet temperature can significantly reduce the CO and THC emissions. For the air jet duration comparisons, both too short and too long air jet durations could induce higher NOx emission. A higher air jet duration would result in higher CO emission due to the more high-pressure air jet with relatively low temperature.

ChemInform Abstract: Organic High-Temperature Syntheses. Part 30. Formation of Thienothiophenes (III), (IV) in the High-Temperature Reaction of 2-Chlorothiophene (I) with Compounds (II) Containing Et-S-Groups.

ChemInform ◽  
1989 ◽  
Vol 20 (10) ◽  
Author(s):  
N. A. KORCHEVIN ◽  
E. N. SUKHOMAZOVA ◽  
L. P. TURCHANINOVA ◽  
G. G. EFREMOVA ◽  
N. A. KALININA ◽  
...  
Keyword(s):  
High Temperature ◽  
Temperature Reaction ◽  
High Temperature Reaction

Effect of Mineral Composition and Sintering Temperature on the Synthetic Cordierite

2014 ◽  
Vol 633 ◽  
pp. 61-64
Author(s):  
Lei Li ◽  
Rui Long Wen ◽  
Xiao Guang Zhang ◽  
Cheng Biao Wang ◽  
Ming Hao Fang ◽  
...  
Keyword(s):  
Phase Composition ◽  
High Temperature ◽  
Flexural Strength ◽  
Mineral Composition ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Temperature Reaction ◽  
Final Phase ◽  
High Temperature Reaction ◽  
Industrial Alumina

Cordierite samples were prepared using quartz sand tailings, industrial alumina and magnesite tailings as raw materials by high-temperature reaction. The influence of mineral composition and sintering temperature on the final phase composition and physical properties of cordierite were studied. The results shown that a large number of cordierite generated at 1300 °C. When the ratio of Al2O3/SiO2 equals to 1.08, the flexural strength of samples increased to 27.66 MPa.

Sign in / Sign up

Export Citation Format

Share Document