Concerning the error of the statistical method of determining the dependence of combustion characteristics on particle size

1974 ◽  
Vol 7 (4) ◽  
pp. 474-476
Author(s):  
E. S. Ozerov ◽  
S. A. Chivilikhin ◽  
A. A. Yurinov
Author(s):  
Joana Freitas Campana ◽  
Kaio Pandolfi Pessotti ◽  
Carlos Eduardo Silva Abreu ◽  
Patrick de Jesus

2013 ◽  
Vol 805-806 ◽  
pp. 200-207
Author(s):  
Bing Zhang ◽  
Guang Wu Lu

Under different conditions,combustion characteristics of the single biomass,the single coal and the mixture of biomass and coal were analyzed by using thermogravimetric analyzer. Combustion characteristic parameters of the sawdust,the rice husk,the rice straw and the Baisha coal of Leiyang were studied,including ignition temperature,the maximum rate of combustion temperature,the burnout temperature and so on. The experimental results show that the biomass burning temperature is lower than the Baisha coal and there are two obvious weight loss phases in the combustion process of the biomass. However,there is only one in the coal. The ignition temperature and time of the coal can be reduced ,the temperature range of the entire combustion can be extended,the coal can be burnout more well and the fuel combustion characteristic can be optimized by blending combustion. With the increase of biomass mixing proportion, the ignition temperature of mixing samples was decreased more obviously. Moreover,when the biomass particle size becomes R200,compared with R90 particle size under the same blending ratio,its ignition temperature is more lower.


2013 ◽  
Vol 1521 ◽  
Author(s):  
Yasmine Aly ◽  
Vern K. Hoffman ◽  
Mirko Schoenitz ◽  
Edward L. Dreizin

ABSTRACTAdding aluminum to propellants, pyrotechnics, and explosives is a common way to boost their energy density. A number of approaches have been investigated that shorten aluminum ignition delay, increase combustion rate, and decrease the tendency of aluminum droplets to agglomerate. Previous work showed that particles of mechanically alloyed Al-Mg powders burn faster than similarly sized particles of pure aluminum. However, preparation of mechanically alloyed powders with particle sizes matching those of fine aluminum used in energetic formulations was not achieved. This work is focused on preparation of mechanically alloyed, composite Al-Mg powders in which both internal structures and particle size distributions are adjusted. Binary powders with compositions in the range of 50 - 90 at. % Al were prepared and characterized. Milling protocol is optimized to prepare equiaxial, micron-scale particles suitable for laboratory evaluations of their oxidation, ignition, and combustion characteristics. Quantitative particle size analyses are done using low-angle laser light scattering. Electron microscopy and x-ray diffraction are used to examine particle morphology and phase makeup, respectively. Combustion of aerosolized powder clouds is studied using a constant volume explosion setup. For all materials, ignition and combustion characteristics are compared to each other and to those of pure Al. Compositions with improved performance (i.e., shorter ignition delay and faster pressurization rate) compared to pure Al are identified.


1969 ◽  
Vol 5 (3) ◽  
pp. 304-305 ◽  
Author(s):  
M. A. Gurevich ◽  
G. V. Ignatov ◽  
E. S. Ozerov ◽  
B. I. Sotnichenko

2014 ◽  
Vol 187 (7) ◽  
pp. 1036-1043 ◽  
Author(s):  
Mingxia Zha ◽  
Xuewen Lv ◽  
Zhenye Ma ◽  
Lixiong Zhang ◽  
Fengqi Zhao ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document