Numerical simulation of gas and particle flow in a high-velocity oxygen-fuel (HVOF) torch

1995 ◽  
Vol 4 (4) ◽  
pp. 358-366 ◽  
Author(s):  
C. H. Chang ◽  
R. L. Moore
Keyword(s):  
Numerical Simulation ◽  
High Velocity ◽  
Particle Flow ◽  
High Velocity Oxygen Fuel ◽  
Oxygen Fuel

COLMONOY NO. 43HV

Alloy Digest ◽  
2008 ◽  
Vol 57 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Surface Treatment ◽  
High Velocity ◽  
Base Alloy ◽  
Heat Treating ◽  
High Velocity Oxygen Fuel ◽  
Nickel Base Alloy ◽  
Nickel Base ◽  
Oxygen Fuel

Abstract Colmonoy No. 43HV comprises a nickel-base alloy recommended for hard surfacing parts to resist wear, corrosion, heat, and galling. Deposits that have moderate hardness have increased ductility and slightly less resistance to abrasion than Colmonoy 53HV. Deposits can be finished by grinding or machined with carbide tooling. Colmonoy No. 43HV is supplied as an atomized powder specially sized for application with high-velocity oxygen fuel (HVOF) systems. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance and surface qualities as well as heat treating and surface treatment. Filing Code: Ni-664. Producer or source: Wall Colmonoy Corporation.

Difference oxidation behaviors of Ni8Al and Ni25Cr coatings in air with water vapor at 650∘

2021 ◽  
pp. 2150274
Author(s):  
Dingjun Li ◽  
Wenlang Huang ◽  
Xiaohu Yuan ◽  
Taihong Huang ◽  
Chao Li ◽  
...  
Keyword(s):  
Water Vapor ◽  
High Velocity ◽  
Cyclic Oxidation ◽  
Oxidation Behaviour ◽  
Fuel Spray ◽  
High Velocity Oxygen Fuel ◽  
Service Environment ◽  
Generator Unit ◽  
Oxygen Fuel ◽  
Oxidation Behaviors

The oxidation behaviour of Ni8Al and Ni25Cr coatings produced by high velocity oxygen fuel spray (HVOF) which were deposited on Fe-based alloys (CB2) was investigated. We simulated the service environment of the steam generator unit, and put the samples in a thermostatic tube furnace at 650[Formula: see text] in air with 20 wt.% water vapor for 1000 hours of cyclic oxidation. The formation mechanism are explained using SEM, XRD, and EDX. There were no spallations and obvious cracks in both coatings. Ni25Cr coating generated a better protection oxides scale than that scale on Ni8Al. The behavior and mechanism of the oxide scale formation had an important influence in coatings and we have discussed these phenomenons in the study.

scholarly journals Pengaruh Proses Oksidasi Lapisan Metal Matrix Composite pada Substrat SS316

2019 ◽  
Vol 4 (2) ◽  
pp. 277
Author(s):  
Erie Martides ◽  
Candra Dewi Romadhona ◽  
Djoko Hadi Prajitno ◽  
Budi Prawara
Keyword(s):  
Metal Matrix Composite ◽  
Thermal Spray ◽  
Matrix Composite ◽  
High Velocity ◽  
Metal Matrix ◽  
Spray Coating ◽  
Thermal Spray Coating ◽  
High Velocity Oxygen Fuel ◽  
Hvof Thermal Spray ◽  
Oxygen Fuel

Material SS316 seringkali digunakan untuk komponen yang bekerja pada temperatur tinggi dengan resiko mengalami oksidasi yang menyebabkan penurunan sifat material dan umur pakai dari komponen. Deposisi Metal Matrix Composite (MMC) NiCr+Cr3C2+Al2O3 dan NiCr+WC12Co+Al2O3 menggunakan metode High Velocity Oxygen Fuel (HVOF) thermal spray coating dengan parameter konstan dilakukan sebagai proses perlakuan pada permukaan SS316 untuk meningkatkan nilai kekerasan dan ketahanan terhadap oksidasi.  Tujuan penelitian ini adalah untuk mengetahui pengaruh proses oksidasi lapisan MMC pada material substrat SS316. Proses oksidasi dilakukan dengan variasi temperatur 500° dan 600°C, penahanan temperatur selama 6 jam, kemudian diteruskan dengan karakterisasi serta perhitungan laju oksidasi. Hasil penelitian menunjukkan spesimen MMC NiCr+Cr3C2+Al2O3 yang dilakukan proses oksidasi pada suhu 500°C memiliki laju oksidasi terendah yaitu 6,67 x 10-7 gram/mm2 jam. 

scholarly journals Influence of Chromium Concentration on the Abrasive Wear Of Ni-Cr-B-Si Coatings Applied by High-Velocity Oxygen Fuel

2021 ◽  
Author(s):  
Zhetcho Doinov Kalitchin ◽  
Mara Krumova Kandeva ◽  
Yana Petrova Stoyanova
Keyword(s):  
Wear Resistance ◽  
Thermal Treatment ◽  
High Velocity ◽  
Composite Coatings ◽  
Research Work ◽  
Wear Intensity ◽  
High Velocity Oxygen Fuel ◽  
Preliminary Thermal Treatment ◽  
Cr Concentration ◽  
Oxygen Fuel

This research work studies the characteristics of wear and wear resistance of composite powder coatings, deposited by high-velocity oxygen fuel, which contain composite mixtures Ni-Cr-B-Si having different chromium concentrations – 9.9%; 13.2%; 14%; 16% and 20% , at one and the same size of the particles and the same content of the remaining elements. The coating of 20% Cr does not contain B and Si. Out of each powder, composite coatings have been prepared without any preliminary thermal treatment of the substrate and with preliminary thermal treatment of the substrate up to 650оС. The coatings have been tested under identical conditions of dry friction over a surface of solid firmly attached abrasive particles using the tribological testing device „Pin-on-disk“. Results have been obtained and the dependences of the hardness, mass wear, intensity of the wearing process, absolute and relative wear resistance on the Cr concentration under identical conditions of friction. It has been found out that for all the coatings the preliminary thermal treatment of the substrate leads to a decrease in the wear intensity. Upon increasing Cr concentration the wear intensity diminishes and it reaches minimal values at 16% Cr. In the case of coatings having 20% Cr concentration, the wear intensity is increased, which is due to the absence of the components B and Si in the composite mixture, whereupon no inter-metallic structures are formed having high hardness and wear resistance. The obtained results have no analogues in the current literature and they have not been published by the authors.

Sign in / Sign up

Export Citation Format

Share Document