Air-side heat transfer and pressure drop of the fin-and-tube heat exchangers having oval tubes under wet condition

2021 ◽  
Author(s):  
Nae-Hyun Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Wet Condition

HEAT TRANSFER AND PRESSURE DROP CHARACTERISTICS OF FIN-AND-TUBE HEAT EXCHANGERS HAVING SPIRAL FINS UNDER WET CONDITIONS

2011 ◽  
Vol 19 (03) ◽  
pp. 185-193 ◽  
Author(s):  
JIN-WOOK LEE ◽  
NAE-HYUN KIM ◽  
HYUN-MIN SIM
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
F Factor ◽  
Wet Condition ◽  
Wet Surface

In this study, wet surface j and f factors were obtained for spiral fin-and-tube heat exchangers. Nine samples having different fin pitches (2.12, 2.54 and 3.18 mm) and different tube rows (1, 2 and 3 row) were tested. Data are compared with those of the dry surface. For the wet surface, the effect of fin pitch on j factor is not significant. However, f factor decreases as the number of tube row increases. The j factor increases as the number of tube row increases. Different from the j factor, f factor decreases as the number of tube row increases. At one row configuration, the dry surface j factor is larger than that of the wet surface one. As the number of tube row increases, the trend is gradually reversed. Possible reasoning is provided considering the condensate behavior under wet condition. A new j and f factor correlation is developed, which predicts j and f factors within ± 20% and ± 30%, respectively.

scholarly journals A MCDM Methodology to Determine the Most Critical Variables in the Pressure Drop and Heat Transfer in Minichannels

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2069
Author(s):  
Eloy Hontoria ◽  
Alejandro López-Belchí ◽  
Nolberto Munier ◽  
Francisco Vera-García
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Saturation Pressure ◽  
Computational Cost ◽  
Urban Systems ◽  
Condensation Process ◽  
Geometrical Parameters ◽  
Maximum Heat ◽  
Maximum Heat Transfer

This paper proposes a methodology aiming at determining the most influent working variables and geometrical parameters over the pressure drop and heat transfer during the condensation process of several refrigerant gases using heat exchangers with pipes mini channels technology. A multi-criteria decision making (MCDM) methodology was used; this MCDM includes a mathematical method called SIMUS (Sequential Interactive Modelling for Urban Systems) that was applied to the results of 2543 tests obtained by using a designed refrigeration rig in which five different refrigerants (R32, R134a, R290, R410A and R1234yf) and two different tube geometries were tested. This methodology allows us to reduce the computational cost compared to the use of neural networks or other model development systems. This research shows six variables out of 39 that better define simultaneously the minimum pressure drop, as well as the maximum heat transfer, saturation pressure fluid entering the condenser being the most important one. Another aim of this research was to highlight a new methodology based on operation research for their application to improve the heat transfer energy efficiency and reduce the CO2 footprint derived of the use of heat exchangers with minichannels.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

Performance Study of Heat Exchangers with Continuous Helical Baffles on Different Inclination Angles

2013 ◽  
Vol 655-657 ◽  
pp. 461-464 ◽  
Author(s):  
Su Fang Song
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Performance Study ◽  
Three Dimensional Model ◽  
Shell Side ◽  
Inclination Angles

The three-dimensional model of heat exchangers with continuous helical baffles was built. The fluid flow dynamics and heat transfer of shell side in the helical baffled heat exchanger were simulated and calculated. The velocity, pressure and temperature distributions were achieved. The simulation shows that with the same baffle pitch, shell-side heat transfer coefficient increased by 25% and the pressure drop decreases by 18% in helical baffled heat exchanger compared with segmental helical baffles. With the analyzing of the flow and heat transfer in heat exchanger in 5 different inclination angles from 11°to 21°, it can be found that both shell side heat transfer coefficient and pressure drop will reduce respectively by 86% and 52% with the increases 11°to 21°of the inclination angles. Numerical simulation provided reliable theoretical reference for further engineering research of heat exchanger with helical baffles.

Pressure Drop and Heat Transfer Characteristics of Louvered Fin Heat Exchangers

2013 ◽  
Vol 465-466 ◽  
pp. 500-504 ◽  
Author(s):  
Shahrin Hisham Amirnordin ◽  
Hissein Didane Djamal ◽  
Mohd Norani Mansor ◽  
Amir Khalid ◽  
Md Seri Suzairin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Considerable Effect ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Louvered Fin

This paper presents the effect of the changes in fin geometry on pressure drop and heat transfer characteristics of louvered fin heat exchanger numerically. Three dimensional simulation using ANSYS Fluent have been conducted for six different configurations at Reynolds number ranging from 200 to 1000 based on louver pitch. The performance of this system has been evaluated by calculating pressure drop and heat transfer coefficient. The result shows that, the fin pitch and the louver pitch have a very considerable effect on pressure drop as well as heat transfer rate. It is observed that increasing the fin pitch will relatively result in an increase in heat transfer rate but at the same time, the pressure drop will decrease. On the other hand, low pressure drop and low heat transfer rate will be obtained when the louver pitch is increased. Final result shows a good agreement between experimental and numerical results of the louvered fin which is about 12%. This indicates the capability of louvered fin in enhancing the performance of heat exchangers.

Single-Phase Heat Transfer and Pressure Drop of Water Cooled Inside Horizontal Smooth Tubes in the Transitional Flow Regime

2010 ◽  
Author(s):  
Josua P. Meyer ◽  
Leon Liebenberg ◽  
Jonathan A. Olivier
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Transition Region ◽  
Heat Exchangers ◽  
Operating Conditions ◽  
Transitional Flow ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Smooth Tubes

Heat exchangers are usually designed in such a way that they do not operate in the transition region. This is usually due to a lack of information in this region. However, due to design constraints, energy efficiency requirements or change of operating conditions, heat exchangers are often forced to operate in this region. It is also well known that entrance disturbances influence where transition occurs. The purpose of this paper is to present experimental heat transfer and pressure drop data in the transition region for fully developed and developing flows inside smooth tubes using water as the working fluid. The use of different inlet disturbances were used to investigate its effect on transition. A tube-in-tube heat exchanger was used to perform the experiments, which ranged in Reynolds numbers from 1 000 to 20 000, with Prandtl numbers being between 4 and 6 while Grashof numbers were in the order of 105. Results showed that the type of inlet disturbance could delay transition to a Reynolds number as high as 7 000, while other inlets expedited it, confirming results of others. For heat transfer, though, it was found that transition was independent of the inlet disturbance and all commenced at the same Reynolds number, 2 000–3 000, which was attributed to secondary flow effects.

CFD Aided Design of Heat Transfer Plates for Gasketed Plate Heat Exchangers

2014 ◽  
Author(s):  
Ece Özkaya ◽  
Selin Aradag ◽  
Sadik Kakac
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Three Dimensional ◽  
Separate Flow ◽  
Working Fluid ◽  
Number Range ◽  
Plate Heat ◽  
Pressure Distributions ◽  
Cfd Analyses

In this study, three-dimensional computational fluid dynamics (CFD) analyses are performed to assess the thermal-hydraulic characteristics of a commercial Gasketed Plate Heat Exchangers (GPHEx) with 30 degrees of chevron angle (Plate1). The results of CFD analyses are compared with a computer program (ETU HEX) previously developed based on experimental results. Heat transfer plate is scanned using photogrammetric scan method to model GPHEx. CFD model is created as two separate flow zones, one for each of hot and cold domains with a virtual plate. Mass flow inlet and pressure outlet boundary conditions are applied. The working fluid is water. Temperature and pressure distributions are obtained for a Reynolds number range of 700–3400 and total temperature difference and pressure drop values are compared with ETU HEX. A new plate (Plate2) with corrugation pattern using smaller amplitude is designed and analyzed. The thermal properties are in good agreement with experimental data for the commercial plate. For the new plate, the decrease of the amplitude leads to a smaller enlargement factor which causes a low heat transfer rate while the pressure drop remains almost constant.

Sign in / Sign up

Export Citation Format

Share Document