Single-Phase Heat Transfer and Pressure Drop of Water Cooled Inside Horizontal Smooth Tubes in the Transitional Flow Regime

2010 ◽  
Author(s):  
Josua P. Meyer ◽  
Leon Liebenberg ◽  
Jonathan A. Olivier
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Transition Region ◽  
Heat Exchangers ◽  
Operating Conditions ◽  
Transitional Flow ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Smooth Tubes

Heat exchangers are usually designed in such a way that they do not operate in the transition region. This is usually due to a lack of information in this region. However, due to design constraints, energy efficiency requirements or change of operating conditions, heat exchangers are often forced to operate in this region. It is also well known that entrance disturbances influence where transition occurs. The purpose of this paper is to present experimental heat transfer and pressure drop data in the transition region for fully developed and developing flows inside smooth tubes using water as the working fluid. The use of different inlet disturbances were used to investigate its effect on transition. A tube-in-tube heat exchanger was used to perform the experiments, which ranged in Reynolds numbers from 1 000 to 20 000, with Prandtl numbers being between 4 and 6 while Grashof numbers were in the order of 105. Results showed that the type of inlet disturbance could delay transition to a Reynolds number as high as 7 000, while other inlets expedited it, confirming results of others. For heat transfer, though, it was found that transition was independent of the inlet disturbance and all commenced at the same Reynolds number, 2 000–3 000, which was attributed to secondary flow effects.

scholarly journals CFD Study Based on Effect of Employing the Single-Walled Carbon Nanotube (SWCNT) and Graphene Quantum Dots (GQD) Nanoparticles and a Particular Fin Configuration on the Thermal Performance in the Shell and Tube Heat Exchanger

CFD letters ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 37-60
Author(s):  
Mohammadreza Hasandust Rostami ◽  
Barat Ghobadian ◽  
Gholamhassan Najafi ◽  
Ali Motevali ◽  
Nor Azwadi Che Sidik
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Concentration ◽  
Working Fluid ◽  
Tube Heat Exchanger ◽  
Average Temperature

In this research, the thermal attributes of shell and finned tube heat exchanger such as thermal efficiency, pressure drop, heat transfer rate and average temperature in the tube side of heat exchanger with using the different volume concentration of nanoparticles (SWCNT and Graphene quantum dot) at the various Reynolds number by applying either fin blades and without fin blades have been conducted numerically. In this heat exchanger the hot fluid or nanofluid flows in the tube section and cold fluid or pure water moves in the shell side. As regarding to results obtained the majority of thermal characteristics like heat transfer rate, pressure drop and effectiveness enhanced with augmentation of Reynolds number and increasing of volume concentration of nanofluids to 1% volumetric of working fluid whereas at the higher volume concentrations of nanoparticles (upper from 1% volumetric) the thermal properties of heat exchanger decreased generally. Also pressure drop intensifies with increment of Reynolds number and volume concentration of nanoparticles that at higher Reynolds number the effects of nanoparticles on the pressure drop were more noticeable. The average temperature of heat exchanger in the end section of inside tubes increased with augmentation of Reynolds number and nanoparticles. Finally, according to the results obtained in this study, most impression on the thermal attributes enhancement was found by employing of finned tubes compared to other factor which this factor increased heat transfer rate of heat exchanger by almost 188% also the effects of nanoparticles at the high levels of volume concentration especially for 5% of SWCNT nanoparticle on the pressure drop obtained about 80% compared to the base fluid.

CFD Aided Design of Heat Transfer Plates for Gasketed Plate Heat Exchangers

2014 ◽  
Author(s):  
Ece Özkaya ◽  
Selin Aradag ◽  
Sadik Kakac
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Three Dimensional ◽  
Separate Flow ◽  
Working Fluid ◽  
Number Range ◽  
Plate Heat ◽  
Pressure Distributions ◽  
Cfd Analyses

In this study, three-dimensional computational fluid dynamics (CFD) analyses are performed to assess the thermal-hydraulic characteristics of a commercial Gasketed Plate Heat Exchangers (GPHEx) with 30 degrees of chevron angle (Plate1). The results of CFD analyses are compared with a computer program (ETU HEX) previously developed based on experimental results. Heat transfer plate is scanned using photogrammetric scan method to model GPHEx. CFD model is created as two separate flow zones, one for each of hot and cold domains with a virtual plate. Mass flow inlet and pressure outlet boundary conditions are applied. The working fluid is water. Temperature and pressure distributions are obtained for a Reynolds number range of 700–3400 and total temperature difference and pressure drop values are compared with ETU HEX. A new plate (Plate2) with corrugation pattern using smaller amplitude is designed and analyzed. The thermal properties are in good agreement with experimental data for the commercial plate. For the new plate, the decrease of the amplitude leads to a smaller enlargement factor which causes a low heat transfer rate while the pressure drop remains almost constant.

scholarly journals Experimental Investigation of Embedded Micropin-Fins for Single-Phase Heat Transfer and Pressure Drop

2018 ◽  
Vol 140 (2) ◽  
Author(s):  
Chirag R. Kharangate ◽  
Ki Wook Jung ◽  
Sangwoo Jung ◽  
Daeyoung Kong ◽  
Joseph Schaadt ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Friction Factor ◽  
Integrated Circuit ◽  
Single Phase ◽  
Absolute Error ◽  
Heat Fluxes ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pin Fin

Three-dimensional (3D) stacked integrated circuit (IC) chips offer significant performance improvement, but offer important challenges for thermal management including, for the case of microfluidic cooling, constraints on channel dimensions, and pressure drop. Here, we investigate heat transfer and pressure drop characteristics of a microfluidic cooling device with staggered pin-fin array arrangement with dimensions as follows: diameter D = 46.5 μm; spacing, S ∼ 100 μm; and height, H ∼ 110 μm. Deionized single-phase water with mass flow rates of m˙ = 15.1–64.1 g/min was used as the working fluid, corresponding to values of Re (based on pin fin diameter) from 23 to 135, where heat fluxes up to 141 W/cm2 are removed. The measurements yield local Nusselt numbers that vary little along the heated channel length and values for both the Nu and the friction factor do not agree well with most data for pin fin geometries in the literature. Two new correlations for the average Nusselt number (∼Re1.04) and Fanning friction factor (∼Re−0.52) are proposed that capture the heat transfer and pressure drop behavior for the geometric and operating conditions tested in this study with mean absolute error (MAE) of 4.9% and 1.7%, respectively. The work shows that a more comprehensive investigation is required on thermofluidic characterization of pin fin arrays with channel heights Hf < 150 μm and fin spacing S = 50–500 μm, respectively, with the Reynolds number, Re < 300.

The Effect of Geometrical Features on Air-Side Heat Transfer and Friction Characteristics, and Optimization of a Large-Size Plain Fin-and-Tube Heat Exchanger by 3-D Numerical Simulation

2009 ◽  
Author(s):  
M. Izadi ◽  
D. K. Aidun ◽  
P. Marzocca ◽  
H. Lee
Keyword(s):  
Heat Transfer ◽  
Numerical Modeling ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Simple Algorithm ◽  
Operating Conditions ◽  
Friction Characteristics ◽  
Tube Heat Exchanger ◽  
Large Size ◽  
Geometrical Features

The effect of geometrical features on the air-side heat transfer and friction characteristics of an industrial plain fin-and-tube heat exchanger is investigated by 3-D numerical modeling and simulations. The heat exchanger has been designed and employed as an intercooler in a gas power plant and is a large-size compact heat exchanger. Most of the available design correlations developed so far for plain fin–and–tube heat exchangers have been prepared for small-size exchangers and none of them fits completely to the current heat exchanger regarding the geometrical limitations of correlations. It is shown that neglecting these limitations and applying improper correlations may generate considerable amount of error in the design of such a large-size heat exchanger. The geometry required for numerical modeling is produced by Gambit® software and the boundary conditions are defined regarding the real operating conditions. Then, three-dimensional simulations based on the SIMPLE algorithm in laminar flow regime are performed by FLUENT™ code. The effect of fin pitch, tube pitch, and tube diameter on the thermo-hydraulic behavior of the heat exchanger is studied. Some variations in the design of the heat exchanger are suggested for optimization purposes. It is finally concluded that the current numerical model is a powerful tool to design and optimize of large-size plain fin-and-tube heat exchangers with acceptable accuracy.

Experimental Study on Forced Convection Heat Transfer Inside Horizontal Tubes in an Absorption/Compression Heat Pump

2002 ◽  
Vol 124 (5) ◽  
pp. 975-978 ◽  
Author(s):  
Li Yong and ◽  
K. Sumathy
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Forced Convection ◽  
Experimental Results ◽  
Working Fluid ◽  
Large Temperature ◽  
Absorption Process ◽  
Transfer Coefficients ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients

Quasi-local absorption heat transfer coefficients and pressure drop inside a horizontal tube absorber have been investigated experimentally, with R-22/DMA as the working pair. The absorber is a counterflow coaxial tube-in-tube heat-exchanger with the working fluid flowing in the inner tube while the water moves through the annulus. A large temperature gliding has been experienced during the absorption process. Experimental results show that the heat transfer coefficient of the forced convective vapor absorption process is higher compared to the vertical falling film absorption. A qualitative study is made to analyze the effect of mass flux, vapor quality and solution concentration on pressure drop and heat transfer coefficients. On the basis of the experimental results, a new correlation is proposed whereby the two-phase heat transfer is taken as a product of the forced convection of the absorption and the combined effect of heat and mass transfer at the interface. The correlation is found to predict the experimental data almost within 30 percent.

Impact of an Anisotropic Fin Surface Design on the Thermal-Hydraulic Performance of a Plain-Fin-and-Tube Heat Exchanger

2011 ◽  
Author(s):  
Rong Yu ◽  
Andrew D. Sommers ◽  
Nicole C. Okamoto ◽  
Koushik Upadhyayula
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Hydraulic Performance ◽  
Normal Operation ◽  
Surface Design ◽  
Tube Heat Exchanger ◽  
Silane Coating ◽  
Side Pressure

In this study, we have explored the effectiveness of heat exchangers constructed using anisotropic, micro-patterned aluminum fins to more completely drain the condensate that forms on the heat transfer surface during normal operation with the aim of improving the thermal-hydraulic performance of the heat exchanger. This study presents and critically evaluates the efficacy of full-scale heat exchangers constructed from these micro-grooved surfaces by measuring dry/wet air-side pressure drop and dry/wet air-side heat transfer data. The new fin surface design was shown to decrease the core pressure drop of the heat exchanger during wet operation from 9.3% to 52.7%. Furthermore, these prototype fin surfaces were shown to have a negligible effect on the heat transfer coefficient under both dry and wet conditions while at the same time reducing the wet airside pressure drop thereby decreasing fan power consumption. That is to say, this novel fin surface design has shown the ability, through improved condensate management, to enhance the thermal-hydraulic performance of plain-fin-and-tube heat exchangers used in air-conditioning applications. This paper also presents data pertaining to the durability of the alkyl silane coating.

CFD Simulation of Fin-and-Tube Heat Exchanger with Louvered Fin Configuration: Technical Note

2017 ◽  
Vol 9 (3) ◽  
Author(s):  
M. Sabari ◽  
D. Channankiah ◽  
D. Shivalingappa
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Cfd Simulation ◽  
Calculated Data ◽  
Technical Note ◽  
Operating Conditions ◽  
Tube Heat Exchanger ◽  
Louvered Fin ◽  
Almost All

Heat exchanger plays a major role in almost all mechanical industries. Enhancement of heat transfer surface plays major role in numerous applications such as in heat exchangers, refrigeration and air conditioning systems etc. This paper examines the fluid flow and heat exchange on the air side of a multi-row fin-and-tube heat exchanger. A brief comparison is given between fin-and-tube heat exchanger attributes with louvered fins in a wider range of operating conditions defined by inlet air velocities. The brief representation on the calculated data for the louvered heat exchanger shows better heat transfer characteristics with a slightly higher pressure drop. The CFD procedure is validated by comparing the numerical simulation results with different inlet air velocities. Best combination of higher heat transfer and minimum pressure drop are occurred in inlet air velocity of 2.5 m/s.

Comparative Experimental Study on Performance of Corrugated Tube and Straight Tube Heat Exchanger

2012 ◽  
Vol 560-561 ◽  
pp. 156-160
Author(s):  
Lin Ping Lu ◽  
Liang Ying
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Straight Tube ◽  
Lower Stress ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Corrugated Tube

The experiments on heat transfer coefficient, pressure drop and thermal stress were done to heat exchangers with corrugated tubes and staight tubes. By analyising and comparing the heat transfer coeffient, pressure drop in tube side and shell side and axial force and stress, some conclusions can be conducted that the corrugated tube heat exchanger has better heat transfer coeffient, higher pressure drop and much lower stress caused by temperatur difference, also, it has obvious advantages under the circumstance of low Reynolds number and high temperature difference.

Performance Evaluation of Tube-in-Tube Heat Exchanger Using Nanofluids

2015 ◽  
Vol 787 ◽  
pp. 72-76 ◽  
Author(s):  
V. Naveen Prabhu ◽  
M. Suresh
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Thermal Performance ◽  
Transfer Rate ◽  
Flow Characteristics ◽  
Operating Conditions ◽  
Element Analysis ◽  
Tube Heat Exchanger

Nanofluids are fluids containing nanometer-sized particles of metals, oxides, carbides, nitrides, or nanotubes. They exhibit enhanced thermal performance when used in a heat exchanger as heat transfer fluids. Alumina (Al2O3) is the most commonly used nanoparticle due to its enhanced thermal conductivity. The work presented here, deals with numerical simulations performed in a tube-in-tube heat exchanger to study and compare flow characteristics and thermal performance of a tube-in-tube heat exchanger using water and Al2O3/water nanofluid. A local element-by-element analysis utilizing e-NTU method is employed for simulating the heat exchanger. Profiles of hot and cooling fluid temperatures, pressure drop, heat transfer rate along the length of the heat exchanger are studied. Results show that heat exchanger with nanofluid gives improved heat transfer rate when compared with water. However, the pressure drop is more, which puts a limit on the operating conditions.

A study of non-redirection louvre fin-and-tube heat exchangers

1998 ◽  
Vol 212 (1) ◽  
pp. 1-14 ◽  
Author(s):  
C-C Wang ◽  
Y-P Chang ◽  
K-Y Chi ◽  
Y-J Chang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Wind Tunnel ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Geometrical Parameters ◽  
Tube Size ◽  
Collar Diameter ◽  
Fanning Friction Factor

Extensive experiments on the heat transfer and pressure drop characteristics of louvre finand-tube heat exchangers were carried out. In the present study, 14 samples of non-redirection louvre fin-and-tube heat exchangers with different geometrical parameters, including the number of tube row, fin pitch and tube size, were tested in a wind tunnel. Results are presented as plots of the Fanning friction factor f and the Colburn j factor against Reynolds number based on the tube collar diameter in the range of 300–8000.

Sign in / Sign up

Export Citation Format

Share Document