Wound morphology in contact shots from blank cartridge handguns: a study on composite models

2017 ◽  
Vol 131 (5) ◽  
pp. 1333-1339 ◽  
Author(s):  
Rebecca Pircher ◽  
Markus Große Perdekamp ◽  
Annette Thierauf-Emberger ◽  
Lena Kramer ◽  
Stefan Pollak ◽  
...  
Author(s):  
Jan Euteneuer ◽  
Annica Gosch ◽  
Cornelius Courts

AbstractBlank cartridge guns are prevalent especially in countries with laws restricting access to conventional firearms, and it is a common misconception that these weapons are harmless and only used as toys or for intimidation. However, although their harming potential is well-documented by numerous reports of accidents, suicides, and homicides, a systematic molecular biological investigation of traces generated by shots from blank cartridges at biological targets has not been done so far. Herein, we investigate the occurrence and analyzability of backspatter generated by shots of different types of blank cartridge guns firing different types of blank ammunition at ballistic gelatin model cubes doped with human blood and radiological contrast agent soaked into a spongious matrix and covered with three different variants of skin simulants. All skin simulants were penetrated, and backspatter was created in 100% of the shots in amounts sufficient for forensic short tandem repeat (STR) typing that resulted in the correct identification of the respective blood donor. Visible backspatter was documented on the muzzle and/or inside the barrel in all cases, and in 75% of cases also on the outer surfaces and on the shooter’s hand(s). Wound cavities were measured and ranged between 1 and 4.5 cm in depth. Discussing our findings, we provide recommendations for finding, recovering, and analyzing trace material from blank guns, and we demonstrate the considerable hazard potential of these devices, which is further emphasized by the presentation of a comprehensive overview of the pertinent literature on injuries inflicted by blank guns.


Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 111
Author(s):  
Ivana O. Mladenović ◽  
Nebojša D. Nikolić ◽  
Jelena S. Lamovec ◽  
Dana Vasiljević-Radović ◽  
Vesna Radojević

The mechanical characteristics of electrochemically deposited copper coatings have been examined by application of two hardness composite models: the Chicot-Lesage (C-L) and the Cheng-Gao (C-G) models. The 10, 20, 40 and 60 µm thick fine-grained Cu coatings were electrodeposited on the brass by the regime of pulsating current (PC) at an average current density of 50 mA cm−2, and were characterized by scanning electron (SEM), atomic force (AFM) and optical (OM) microscopes. By application of the C-L model we determined a limiting relative indentation depth (RID) value that separates the area of the coating hardness from that with a strong effect of the substrate on the measured composite hardness. The coating hardness values in the 0.9418–1.1399 GPa range, obtained by the C-G model, confirmed the assumption that the Cu coatings on the brass belongs to the “soft film on hard substrate” composite hardness system. The obtained stress exponents in the 4.35–7.69 range at an applied load of 0.49 N indicated that the dominant creep mechanism is the dislocation creep and the dislocation climb. The obtained mechanical characteristics were compared with those recently obtained on the Si(111) substrate, and the effects of substrate characteristics such as hardness and roughness on the mechanical characteristics of the electrodeposited Cu coatings were discussed and explained.


2012 ◽  
Vol 2012 (10) ◽  
Author(s):  
Michele Redi ◽  
Andrea Tesi
Keyword(s):  

1986 ◽  
Vol 266 (2) ◽  
pp. 274-284 ◽  
Author(s):  
Howard Georgi
Keyword(s):  

2021 ◽  
Author(s):  
GEORGE BARLOW ◽  
MATHEW SCHEY ◽  
SCOTT STAPLETON

Modeling composites can be an effective way to understand how a part will perform without requiring the destruction of costly specimens. By combining artificial fiber entanglement with manufacturing process simulation, a method was developed to create fiber bundle models using entanglement to control the fiber volume fraction. This fiber entanglement generation uses three parameters, probability of swapping (p_(r_S )), swapping radius standard deviation (r_(σ_S )), and the swapping plane spacing (l_S), to control the amount of entanglement within the fiber bundle. A parametric study was conducted and found that the more entanglement within a fiber bundle, the more compression mold pressure required to compact the fiber bundle to the same fiber volume fraction as that required for a less entangled bundle. This artificial fiber entanglement and manufacturing process simulation method for creating fiber bundles shows the potential to be able to create bundles with controlled final volume fraction using a desired mold compression pressure.


Sign in / Sign up

Export Citation Format

Share Document