A low power and low noise 60-GHz CMOS receiver front-end with high conversion gain and excellent port-to-port isolation

2015 ◽  
Vol 83 (2) ◽  
pp. 119-128 ◽  
Author(s):  
Yo-Sheng Lin ◽  
Jen-How Lee
Keyword(s):  
Low Power ◽  
Low Noise ◽  
High Conversion ◽  
Conversion Gain ◽  
60 Ghz ◽  
Front End ◽  
Cmos Receiver

scholarly journals Design of a very low-power, low-cost 60 GHz receiver front-end implemented in 65 nm CMOS technology

2011 ◽  
Vol 3 (2) ◽  
pp. 131-138 ◽  
Author(s):  
Michael Kraemer ◽  
Daniela Dragomirescu ◽  
Robert Plana
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Noise Figure ◽  
Low Cost ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Voltage Controlled Oscillator ◽  
60 Ghz ◽  
Front End

The research on the design of receiver front-ends for very high data-rate communication in the 60 GHz band in nanoscale Complementary Metal Oxide Semiconductor (CMOS) technologies is going on for some time now. Although a multitude of 60 GHz front-ends have been published in recent years, they are not consequently optimized for low power consumption. Thus, these front-ends dissipate too much power for battery-powered applications like handheld devices, mobile phones, and wireless sensor networks. This article describes the design of a direct conversion receiver front-end that addresses the issue of power consumption, while at the same time permitting low cost (due to area minimization by the use of spiral inductors). It is implemented in a 65 nm CMOS technology. The realized front-end achieves a record power consumption of only 43 mW including low-noise amplifier (LNA), mixer, a voltage controlled oscillator (VCO), a local oscillator (LO) buffer, and a baseband buffer (without this latter buffer the power consumption is even lower, only 29 mW). Its pad-limited size is 0.55 × 1 mm2. At the same time, the front-end achieves state-of-the-art performance with respect to its other properties: Its maximum measured power conversion gain is 30 dB, the RF and IF bandwidths are 56.5–61.5 and 0–1.5 GHz, respectively, its measured minimum noise figure is 9.2 dB, and its measured IP−1 dB is −36 dBm.

Fully integrated 60 GHz transceiver in SiGe BiCMOS, RF modules, and 3.6 Gbit/s OFDM data transmission

2011 ◽  
Vol 3 (2) ◽  
pp. 139-145 ◽  
Author(s):  
Srdjan Glisic ◽  
J. Christoph Scheytt ◽  
Yaoming Sun ◽  
Frank Herzel ◽  
Ruoyu Wang ◽  
...  
Keyword(s):  
Data Transmission ◽  
Intermediate Frequency ◽  
Phase Locked Loop ◽  
Data Rate ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Integrated ◽  
Front End ◽  
Free Data ◽  
Bicmos Technology

A fully integrated transmitter (TX) and receiver (RX) front-end chipset, produced in 0.25 µm SiGe:C bipolar and complementary metal oxide semiconductor (BiCMOS) technology, is presented. The front-end is intended for high-speed wireless communication in the unlicensed ISM band of 9 GHz around 60 GHz. The TXand RX features a modified heterodyne topology with a sliding intermediate frequency. The TX features a 12 GHz in-phase and quadrature (I/Q) mixer, an intermediate frequency (IF) amplifier, a phase-locked loop, a 60 GHz mixer, an image-rejection filter, and a power amplifier. The RX features a low-noise amplifier (LNA), a 60 GHz mixer, a phase-locked loop (PLL), and an IF demodulator. The measured 1-dB compression point at the TX output is 12.6 dBm and the saturated power is 16.2 dBm. The LNA has measured noise figure of 6.5 dB at 60 GHz. Error-free data transmission with a 16 quadrature amplitude modulation (QAM) orthogonal frequency-division multiplexing (OFDM) signal and data rate of 3.6 Gbit/s (without coding 4.8 Gbit/s) over 15 m was demonstrated. This is the best reported result regarding both the data rate and transmission distance in SiGe and CMOS without beamforming.

scholarly journals A 60 GHz fully differential LNA in 90 nm CMOS technology

2013 ◽  
Vol 6 (2) ◽  
pp. 109-113 ◽  
Author(s):  
Andrea Malignaggi ◽  
Amin Hamidian ◽  
Georg Boeck
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Transmission Lines ◽  
Noise Figure ◽  
Design Procedure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
60 Ghz ◽  
Fully Differential

The present paper presents a fully differential 60 GHz four stages low-noise amplifier for wireless applications. The amplifier has been optimized for low-noise, high-gain, and low-power consumption, and implemented in a 90 nm low-power CMOS technology. Matching and common-mode rejection networks have been realized using shielded coplanar transmission lines. The amplifier achieves a peak small-signal gain of 21.3 dB and an average noise figure of 5.4 dB along with power consumption of 30 mW and occupying only 0.38 mm2pads included. The detailed design procedure and the achieved measurement results are presented in this work.

Sign in / Sign up

Export Citation Format

Share Document