Two Automated Techniques for Carotid Lumen Diameter Measurement: Regional versus Boundary Approaches

2016 ◽  
Vol 40 (7) ◽  
Author(s):  
Tadashi Araki ◽  
◽  
P. Krishna Kumar ◽  
Harman S. Suri ◽  
Nobutaka Ikeda ◽  
...  
2021 ◽  
Vol 8 (6) ◽  
pp. 8-21
Author(s):  
Sujith Pereira ◽  
Jonathan Reeves ◽  
Malcolm Birch ◽  
Ahmed Ali ◽  
Ajay Sinha ◽  
...  

Diameter form an integral part of blood flow measurement. This study aimed to explore different three-dimensional (3D) printed materials to develop flow phantom models of the carotid artery in preterm newborn infants and to investigate ideal diameter measurement points using ultrasound that reflected accurate lumen diameter measurement. Cerebral blood flow measurements data using Doppler ultrasound of the right common carotid artery from 21 randomly selected preterm infants were used to produce a 3D printed Doppler flow phantom model with three different vessel diameters. Diameters were measured by multiple observers blinded to phantom vessel characteristics and each other’s measurements. 9 measurement points were studied. Agreement between observers, inter and intra observer reliability and coefficient of variation (CoV) was examined. Of the 63 diameter measurements, 45 (71%) were performed on flow phantoms with vessel diameter of 0.196 cm. Bland-Altman plots revealed that measurement performed using leading edge to centre (mean bias 1.8% {95%LOA -4.1% to 7.7%}) and centre to trailing edge (mean bias 1.1% {95%LOA -5.4% to 7.8%}) resulted in the most accurate lumen diameter measurements. Inter and intra-observer reliability was excellent. The mean CoV for inter observer measurements was 1.7% and intra observer measurements was 1.6% and 1.8% for each observer. We successfully produced a 3D printed flow phantom model of the carotid artery in preterm infants and identified two measurement methods that result in reliable and accurate lumen diameter measurement. Researchers and clinicians can use this information for further studies involving ultrasound diameter measurements in small calibre vessels.


1999 ◽  
Vol 1 ◽  
pp. S16-S16
Author(s):  
M MATEOS ◽  
A EVANGELISTA ◽  
A SALAS ◽  
M SEBASTIA ◽  
R DOMINGUEZ ◽  
...  

2014 ◽  
Vol 11 (1) ◽  
pp. 51
Author(s):  
Mohd Helmy Ibrahim ◽  
Mohd Nazip Suratman ◽  
Razali Abd Kader

Trees planted from agroforestry practices can become valuable resources in meeting the wood requirements of many nations. Gliricidia sepium is an exotic species introduced to the agricultural sector in Malaysia mainly for providing shade for cocoa and coffee plantations. This study investigates its wood physical properties (specific gravity and moisture content) and fibre morphology (length, lumen diameter and cell wall thickness) of G. sepium at three intervals according to age groups ( three, five and seven years of ages). Specific gravity (0.72) was significantly higher at seven years ofage as compared to five (0.41) and three (0.35) years age group with a mean of 0.43 (p<0.05). Mean moisture content was 58.3% with no significant difference existing between the tree age groups. Fibre diameter (22.4 mm) was significantly lower (p<0.05) for the trees which were three years of age when compared to five and seven years age groups (26.6 mm and 24. 7 mm), respectively. Means of fibre length, lumen diameter and cell wall thickness were 0.83 mm, 18.3 mm, and 6.2 mm, respectively, with no significant differences detected between trees in all age groups. Further calculation on the coefficient of suppleness and runkel ratio suggest that wood from G.sepium may have the potential for insulation board manufacturing and paper making. However, future studies should experiment the utilisation of this species for these products to determine its full potential.


Sign in / Sign up

Export Citation Format

Share Document