Coffee ripeness monitoring using a UAV-mounted low-cost multispectral camera

Multispectral imaging is a widely used remote sensing technique, whose applications range from agriculture to environmental monitoring, from food quality check to cultural heritage diagnostic. A variety of multispectral imaging sensors are available on the market, many of them designed to be mounted on different platform, especially small drones. This work focuses on the geometric and radiometric characterization of a brand-new, lightweight, low-cost multispectral camera, called MAIA. The MAIA camera is equipped with nine sensors, allowing for the acquisition of images in the visible and near infrared parts of the electromagnetic spectrum. Two versions are available, characterised by different set of band-pass filters, inspired by the sensors mounted on the WorlView-2 and Sentinel2 satellites, respectively. The camera details and the developed procedures for the geometric calibrations and radiometric correction are presented in the paper.

Download Full-text

Decomposition of the metastable beta titanium alloy Ti-15-3

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100075117 ◽

1983 ◽

Vol 41 ◽

pp. 264-265

Author(s):

Y. L. Chen ◽

S. Fujlshiro

Keyword(s):

Low Cost ◽

High Strength ◽

Alpha Phase ◽

Thick Sheet ◽

Omega Phase ◽

Beta Titanium Alloy ◽

Beta Titanium ◽

Beta Matrix ◽

Metastable Beta ◽

Very High

Metastable beta titanium alloys have been known to have numerous advantages such as cold formability, high strength, good fracture resistance, deep hardenability, and cost effectiveness. Very high strength is obtainable by precipitation of the hexagonal alpha phase in a bcc beta matrix in these alloys. Precipitation hardening in the metastable beta alloys may also result from the formation of transition phases such as omega phase. Ti-15-3 (Ti-15V- 3Cr-3Al-3Sn) has been developed recently by TIMET and USAF for low cost sheet metal applications. The purpose of the present study was to examine the aging characteristics in this alloy.The composition of the as-received material is: 14.7 V, 3.14 Cr, 3.05 Al, 2.26 Sn, and 0.145 Fe. The beta transus temperature as determined by optical metallographic method was about 770°C. Specimen coupons were prepared from a mill-annealed 1.2 mm thick sheet, and solution treated at 827°C for 2 hr in argon, then water quenched. Aging was also done in argon at temperatures ranging from 316 to 616°C for various times.

Download Full-text

Chromic Acid Etching of Polyethylene

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100070801 ◽

1973 ◽

Vol 31 ◽

pp. 72-73

Author(s):

J. D. Muzzy ◽

R. D. Hester ◽

J. L. Hubbard

Keyword(s):

Chromic Acid ◽

Low Cost ◽

Acid Etching ◽

Crystalline Morphology ◽

Bulk Specimen ◽

Morphological Studies ◽

Perfect Form ◽

Molecular Length ◽

Lamellar Texture ◽

Cost Studies

Polyethylene is one of the most important plastics produced today because of its good physical properties, ease of fabrication and low cost. Studies to improve the properties of polyethylene are leading to an understanding of its crystalline morphology. Polyethylene crystallized by evaporation from dilute solutions consists of thin crystals called lamellae. The polyethylene molecules are parallel to the thickness of the lamellae and are folded since the thickness of the lamellae is much less than the molecular length. This lamellar texture persists in less perfect form in polyethylene crystallized from the melt.Morphological studies of melt crystallized polyethylene have been limited due to the difficulty of isolating the microstructure from the bulk specimen without destroying or deforming it.

Download Full-text

Glass Knife Geometry as Seen by the SEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100066322 ◽

1971 ◽

Vol 29 ◽

pp. 454-455

Author(s):

J. Temple Black

Keyword(s):

Low Cost ◽

Amorphous Material ◽

Stress Concentrations ◽

Basic Tool ◽

Tool Materials ◽

Optical Inspection ◽

Surface Flaws ◽

Slip Planes ◽

Glass Knife ◽

Diamond Knife

In ultramicrotomy, the two basic tool materials are glass and diamond. Glass because of its low cost and ease of manufacture of the knife itself is still widely used despite the superiority of diamond knives in many applications. Both kinds of knives produce plastic deformation in the microtomed section due to the nature of the cutting process and microscopic chips in the edge of the knife. Because glass has no well defined slip planes in its structure (it's an amorphous material), it is very strong and essentially never fails in compression. However, surface flaws produce stress concentrations which reduce the strength of glass to 10,000 to 20,000 psi from its theoretical or flaw free values of 1 to 2 million psi. While the microchips in the edge of the glass or diamond knife are generally too small to be observed in the SEM, the second common type of defect can be identified. This is the striations (also termed the check marks or feathers) which are always present over the entire edge of a glass knife regardless of whether or not they are visable under optical inspection. These steps in the cutting edge can be observed in the SEM by proper preparation of carefully broken knives and orientation of the knife, with respect to the scanning beam.

Download Full-text

Spectraplot: A PC-based spectrum translation and display program

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s042482010010665x ◽

1988 ◽

Vol 46 ◽

pp. 918-919

Author(s):

H. O. Colijn

Keyword(s):

Low Cost ◽

Transfer Program ◽

File Transfer ◽

Transfer Data ◽

Error Checking ◽

Data Files ◽

The University

Many labs today wish to transfer data between their EDS systems and their existing PCs and minicomputers. Our lab has implemented SpectraPlot, a low- cost PC-based system to allow offline examination and plotting of spectra. We adopted this system in order to make more efficient use of our microscopes and EDS consoles, to provide hardcopy output for an older EDS system, and to allow students to access their data after leaving the university.As shown in Fig. 1, we have three EDS systems (one of which is located in another building) which can store data on 8 inch RT-11 floppy disks. We transfer data from these systems to a DEC MINC computer using “SneakerNet”, which consists of putting on a pair of sneakers and running down the hall. We then use the Hermit file transfer program to download the data files with error checking from the MINC to the PC.

Download Full-text