Poisson’s ratios and S-wave velocities of the Xishancun landslide, Sichuan, China, inferred from high-frequency receiver functions of local earthquakes

Author(s):  
Zigen Wei ◽  
Risheng Chu ◽  
Zhiwei Li ◽  
Minhan Sheng ◽  
Qiu Zeng
1996 ◽  
Vol 86 (6) ◽  
pp. 1704-1713 ◽  
Author(s):  
R. D. Catchings ◽  
W. H. K. Lee

Abstract The 17 January 1994, Northridge, California, earthquake produced strong ground shaking at the Cedar Hills Nursery (referred to here as the Tarzana site) within the city of Tarzana, California, approximately 6 km from the epicenter of the mainshock. Although the Tarzana site is on a hill and is a rock site, accelerations of approximately 1.78 g horizontally and 1.2 g vertically at the Tarzana site are among the highest ever instrumentally recorded for an earthquake. To investigate possible site effects at the Tarzana site, we used explosive-source seismic refraction data to determine the shallow (<70 m) P-and S-wave velocity structure. Our seismic velocity models for the Tarzana site indicate that the local velocity structure may have contributed significantly to the observed shaking. P-wave velocities range from 0.9 to 1.65 km/sec, and S-wave velocities range from 0.20 and 0.6 km/sec for the upper 70 m. We also found evidence for a local S-wave low-velocity zone (LVZ) beneath the top of the hill. The LVZ underlies a CDMG strong-motion recording site at depths between 25 and 60 m below ground surface (BGS). Our velocity model is consistent with the near-surface (<30 m) P- and S-wave velocities and Poisson's ratios measured in a nearby (<30 m) borehole. High Poisson's ratios (0.477 to 0.494) and S-wave attenuation within the LVZ suggest that the LVZ may be composed of highly saturated shales of the Modelo Formation. Because the lateral dimensions of the LVZ approximately correspond to the areas of strongest shaking, we suggest that the highly saturated zone may have contributed to localized strong shaking. Rock sites are generally considered to be ideal locations for site response in urban areas; however, localized, highly saturated rock sites may be a hazard in urban areas that requires further investigation.


Geophysics ◽  
2009 ◽  
Vol 74 (2) ◽  
pp. WA93-WA101 ◽  
Author(s):  
Clive McCann ◽  
Jeremy Sothcott

Laboratory measurements of the attenuation and velocity dispersion of compressional and shear waves at appropriate frequencies, pressures, and temperatures can aid interpretation of seismic and well-log surveys as well as indicate absorption mechanisms in rocks. Construction and calibration of resonant-bar equipment was used to measure velocities and attenuations of standing shear and extensional waves in copper-jacketed right cylinders of rocks ([Formula: see text] in length, [Formula: see text] in diameter) in the sonic frequency range and at differential pressures up to [Formula: see text]. We also measured ultrasonic velocities and attenuations of compressional and shear waves in [Formula: see text]-diameter samples of the rocks at identical pressures. Extensional-mode velocities determined from the resonant bar are systematically too low, yielding unreliable Poisson’s ratios. Poisson’s ratios determined from the ultrasonic data are frequency corrected and used to calculate thesonic-frequency compressional-wave velocities and attenuations from the shear- and extensional-mode data. We calculate the bulk-modulus loss. The accuracies of attenuation data (expressed as [Formula: see text], where [Formula: see text] is the quality factor) are [Formula: see text] for compressional and shear waves at ultrasonic frequency, [Formula: see text] for shear waves, and [Formula: see text] for compressional waves at sonic frequency. Example sonic-frequency data show that the energy absorption in a limestone is small ([Formula: see text] greater than 200 and stress independent) and is primarily due to poroelasticity, whereas that in the two sandstones is variable in magnitude ([Formula: see text] ranges from less than 50 to greater than 300, at reservoir pressures) and arises from a combination of poroelasticity and viscoelasticity. A graph of compressional-wave attenuation versus compressional-wave velocity at reservoir pressures differentiates high-permeability ([Formula: see text], [Formula: see text]) brine-saturated sandstones from low-permeability ([Formula: see text], [Formula: see text]) sandstones and shales.


2020 ◽  
Vol 110 (3) ◽  
pp. 1372-1386
Author(s):  
Thayane Victor ◽  
Jordi Julià ◽  
Nicholas J. White ◽  
Verónica Rodríguez-Tribaldos

ABSTRACT We assess the performance of the joint inversion of receiver functions (RF) and surface-wave dispersion in the characterization of the sedimentary package comprising the Parnaíba basin. This procedure is routinely utilized in passive-source crustal studies to retrieve S-wave velocity variations with depth, and has seldom been used with higher-frequency datasets to investigate fine sedimentary structure. The Parnaíba basin is a Paleozoic cratonic basin composed of five supersequences, accumulating ∼3.5  km of sedimentary rocks interbedded by Late Cretaceous diabase sills. The dataset used for this research was acquired between 2015 and 2017 through deployment of 10 short-period and one broadband seismic stations distributed along an approximately 100-kilometer-long linear array in the center of the basin. The deployment was carried out under the Parnaíba Basin Analysis Project, a multi-institutional and multidisciplinary effort funded by BP Energy do Brasil. High-frequency RFs (f<4.8  Hz) were calculated from deconvolution of teleseismic P waveforms (30°<Δ<90°) after rotation into the great-circle path, whereas high-frequency dispersion curves (0.25–2 Hz) were obtained through multiple filter analysis of empirical Green’s functions developed from cross-correlation (ZZ component) and stacking (six months) of time–frequency-normalized ambient seismic noise recordings. S-wave velocity–depth profiles down to ∼5  km depth were developed through an iterative, linearized joint inversion approach. Comparison to independent active-source seismic profiles overlapping with our passive-source seismic line reveals the inverted velocity models successfully retrieve sedimentary thickness (top of the Cambrian), sedimentary velocity structure, and depth to the Cenozoic sedimentary sequence. In addition, high-velocity zones at depths ranging from 1.5 to 2.5 km are observed in the inverted velocity–depth profiles, which are interpreted as due to the Late Cretaceous sills interbedding the basin’s sedimentary rocks. The relative low cost of our approach makes it ideal for basic characterization of relatively unknown sedimentary basins.


Geophysics ◽  
2007 ◽  
Vol 72 (5) ◽  
pp. R77-R85 ◽  
Author(s):  
Donghong Pei ◽  
John N. Louie ◽  
Satish K. Pullammanappallil

The simulated annealing (SA) inversion technique has been successfully applied for solving various nonlinear geophysical problems. Following previous developments, we modified the SA inversion, yielding 1D shallow S-wave velocity profiles from high frequency fundamental-mode Rayleigh dispersion curves, and validated the inversion with blind tests. Unlike previous applications of SA, this study draws random numbers from a standard Gaussian distribution. The numbers simultaneously perturb both S-wave velocities and the layer thickness of models. The annealing temperature is gradually decreased following a polynomial-time cooling schedule. Phase velocities are calculated using the reflectivity-transmission coefficient method. The reliability of the model resulting from our implementation is evaluated by statistically calculating the expected values of model parameters and their covariance matrices. Blind tests on two field and 12 synthetic Rayleigh dispersion data sets show that our SA implementation works well for S-wave velocity inversion of dispersion curves from high-frequency fundamental-mode Rayleigh waves. Blind estimates of layer S-wave velocities fall within one standard deviation of the velocities of the original synthetic models in 78% of cases.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Philipp Balling ◽  
Christoph Grützner ◽  
Bruno Tomljenović ◽  
Wim Spakman ◽  
Kamil Ustaszewski

AbstractThe Dinarides fold-thrust belt on the Balkan Peninsula resulted from convergence between the Adriatic and Eurasian plates since Mid-Jurassic times. Under the Dinarides, S-wave receiver functions, P-wave tomographic models, and shear-wave splitting data show anomalously thin lithosphere overlying a short down-flexed slab geometry. This geometry suggests a delamination of Adriatic lithosphere. Here, we link the evolution of this continental convergence system to hitherto unreported sets of extensively uplifted Oligocene–Miocene (28–17 Ma) marine terraces preserved at elevations of up to 600 m along the Dinaric coastal range. River incision on either side of the Mediterranean-Black Sea drainage divide is comparable to the amounts of terrace uplift. The preservation of the uplifted terraces implies that the most External Dinarides did not experience substantial deformation other than surface uplift in the Neogene. These observations and the contemporaneous emplacement of igneous rocks (33–22 Ma) in the internal Dinarides suggest that the Oligo-Miocene orogen-wide uplift was driven by post-break-off delamination of the Adriatic lithospheric mantle, this was followed by isostatic readjustment of the remaining crust. Our study details how lithospheric delamination exerts an important control on crustal deformation and that its crustal signature and geomorphic imprint can be preserved for millions of years.


Sign in / Sign up

Export Citation Format

Share Document