Effects of confining pressure and loading path on deformation and strength of cohesive granular materials: a three-dimensional DEM analysis

2018 ◽  
Vol 14 (2) ◽  
pp. 443-460 ◽  
Author(s):  
Yulong Zhang ◽  
Jianfu Shao ◽  
Zaobao Liu ◽  
Chong Shi ◽  
Géry De Saxcé
Keyword(s):  
Granular Materials ◽  
Three Dimensional ◽  
Confining Pressure ◽  
Loading Path ◽  
Dem Analysis

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

scholarly journals Quantitative 3D imaging of partially saturated granular materials under uniaxial compression

2021 ◽  
Author(s):  
Marius Milatz ◽  
Nicole Hüsener ◽  
Edward Andò ◽  
Gioacchino Viggiani ◽  
Jürgen Grabe
Keyword(s):  
Granular Materials ◽  
Uniaxial Compression ◽  
Water Clusters ◽  
Local Strain ◽  
Confining Pressure ◽  
Mechanical Effect ◽  
Compression Tests ◽  
Initial Water ◽  
Interfacial Areas ◽  
Membrane Effects

AbstractGauging the mechanical effect of partial saturation in granular materials is experimentally challenging due to the very low suctions resulting from large pores. To this end, a uniaxial (zero radial stress) compression test may be preferable to a triaxial one where confining pressure and membrane effects may erase the contribution of this small suction; however, volume changes are challenging to measure. This work resolves this limitation by using X-ray imaging during in situ uniaxial compression tests on Hamburg Sand and glass beads at three different initial water contents, allowing a suction-dependent dilation to be brought to the light. The acquired tomography volumes also allow the development of air–water and solid–water interfacial areas, water clusters and local strain fields to be measured at the grain scale. These measurements are used to characterise pertinent micro-scale quantities during shearing and to relate them to the measured macroscopic response. The new and well-controlled data acquired during this experimental campaign are hopefully a useful contribution to the modelling efforts—to this end they are shared with the community.

scholarly journals An Evaluation Method of Brittleness Characteristics of Shale Based on the Unloading Experiment

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1779 ◽  
Author(s):  
Xiaogui Zhou ◽  
Haiming Liu ◽  
Yintong Guo ◽  
Lei Wang ◽  
Zhenkun Hou ◽  
...  
Keyword(s):  
Evaluation Method ◽  
Shear Failure ◽  
Confining Pressure ◽  
Shear Zones ◽  
Loading Path ◽  
Mechanical Parameters ◽  
Failure Characteristics ◽  
Unloading Rate ◽  
Uplift And Erosion ◽  
Unloading Effect

Shale reservoir has an initial unloading effect during the natural uplift and erosion process, which causes the shale brittleness to change, affecting the design of the fracturing scheme. To consider this, the axial compression loading and confining pressure unloading experiment of shale is carried out, and then the influence of unloading rate on the mechanical parameters, failure characteristics, and the brittleness of rock are analyzed. What is more, a new evaluation method of brittleness characteristics that take the unloading effect into consideration is proposed. The conclusions are as follows: (1) The unloading rate has a weakening effect on the mechanical parameters, such as the destructive confining pressure and the residual strength of the samples. (2) The failure characteristics of shale specimens are a single shear failure in an oblique section under low unloading rate, and multiple shear zones accompanied with bedding fracture under high unloading rate. (3) The brittleness of shale samples is well verified by the brittleness index B d 1 and B d 2 during the loading path; nevertheless, it has shortage at the unloading path. This paper proposes a new brittleness evaluation method which can consider the influence of the different unloading rates and unloading points. Furthermore, there is a nice characterization between the brittleness damage and this method.

scholarly journals Harnessing the interface mechanics of hard films and soft substrates for 3D assembly by controlled buckling

2019 ◽  
Vol 116 (31) ◽  
pp. 15368-15377 ◽  
Author(s):  
Yuan Liu ◽  
Xueju Wang ◽  
Yameng Xu ◽  
Zhaoguo Xue ◽  
Yi Zhang ◽  
...  
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Functional Materials ◽  
Loading Path ◽  
Weak Interface ◽  
Nonlinear Buckling ◽  
Micromechanical Resonators ◽  
Diverse Range ◽  
3D Assembly ◽  
Engineering Parameters

Techniques for forming sophisticated, 3D mesostructures in advanced, functional materials are of rapidly growing interest, owing to their potential uses across a broad range of fundamental and applied areas of application. Recently developed approaches to 3D assembly that rely on controlled buckling mechanics serve as versatile routes to 3D mesostructures in a diverse range of high-quality materials and length scales of relevance for 3D microsystems with unusual function and/or enhanced performance. Nonlinear buckling and delamination behaviors in materials that combine both weak and strong interfaces are foundational to the assembly process, but they can be difficult to control, especially for complex geometries. This paper presents theoretical and experimental studies of the fundamental aspects of adhesion and delamination in this context. By quantifying the effects of various essential parameters on these processes, we establish general design diagrams for different material systems, taking into account 4 dominant delamination states (wrinkling, partial delamination of the weak interface, full delamination of the weak interface, and partial delamination of the strong interface). These diagrams provide guidelines for the selection of engineering parameters that avoid interface-related failure, as demonstrated by a series of examples in 3D helical mesostructures and mesostructures that are reconfigurable based on the control of loading-path trajectories. Three-dimensional micromechanical resonators with frequencies that can be selected between 2 distinct values serve as demonstrative examples.

Triaxial Characterization of Minnesota Road Research Project Granular Materials

1997 ◽  
Vol 1577 (1) ◽  
pp. 27-36 ◽  
Author(s):  
Navneet Garg ◽  
Marshall R. Thompson
Keyword(s):  
Shear Strength ◽  
Granular Materials ◽  
Resilient Modulus ◽  
Axial Strain ◽  
Confining Pressure ◽  
Engineering Properties ◽  
Shear Tests ◽  
Road Project ◽  
Load Tests ◽  
Repeated Load

Six granular materials were used as base and subbase materials in the flexible pavement test sections for the Minnesota Road Research (Mn/ROAD) project. Crushed/fractured particles are not allowed in aggregate classes CL-1Fsp, CL-1Csp, CL-3sp, and CL-4sp. Ten to 15 percent crushed/fractured particles are required for CL-5sp. One hundred percent crushed/ fractured particles are required for CL-6sp. A comprehensive laboratory testing program was established to determine pertinent engineering properties of the granular materials. Rapid shear tests and repeated-load tests were conducted to determine the shear strength parameters (friction angle and cohesion), resilient modulus, rutting potential, stress history effects on shear strength, and moisture susceptibility. The results from the rapid shear tests and permanent deformation tests show that the rutting potential of a granular material can be characterized from rapid shear test at a confining pressure of 15 psi (103.35 kPa). The rutting parameter A was a function of the shear strength of the granular materials. The shear strength results obtained from rapid shear tests performed at a confining pressure of 15 psi reflect the rutting trends observed in the low-volume road test sections at the Mn/ROAD project. Results from repeated-load tests were used to develop the parameters for K-θ, UT-Austin, and Uzan’s models for evaluating the resilient modulus of granular materials. The axial strain values calculated from the resilient modulus models appear to be in good agreement with the measured axial strain values, except for the very low shear strength material CL-1Csp.

Sign in / Sign up

Export Citation Format

Share Document