Thermal stability of catalyst for ammonia synthesis based on cobalt molybdenum nitrides

The application of cobalt molybdenum nitrides as ammonia synthesis catalysts requires further development of the optimal promoter system, which enhances not only the activity but also the stability of the catalysts. To do so, elucidating the influence of the addition of alkali metals on the structural properties of the catalysts is essential. In this study, potassium-promoted cobalt molybdenum nitrides were synthesized by impregnation of the precursor CoMoO4·3/4H2O with aqueous KNO3 solution followed by ammonolysis. The catalysts were characterized with the use of XRD and BET methods, under two conditions: as obtained and after the thermal stability test. The catalytic activity in the synthesis of ammonia was examined at 450 °C, under 10 MPa. The thermal stability test was carried out by heating at 650 °C in the same apparatus. As a result of ammonolysis, mixtures of two phases: Co3Mo3N and Co2Mo3N were obtained. The phase concentrations were affected by potassium admixture. The catalytical activity increased for the most active catalyst by approximately 50% compared to non-promoted cobalt molybdenum nitrides. The thermal stability test resulted in a loss of activity, on average, of 30%. Deactivation was caused by the collapse of the porous structure, which is attributed to the conversion of the Co2Mo3N phase to the Co3Mo3N phase.

Download Full-text

The Ordered Phase Formation in Ti-Al-Ga Alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100069193 ◽

1970 ◽

Vol 28 ◽

pp. 440-441

Author(s):

Shiro Fujishiro ◽

Harold L. Gegel

Keyword(s):

Thermal Stability ◽

High Temperature ◽

Titanium Alloys ◽

Growth Kinetics ◽

Stoichiometric Composition ◽

Good Potential ◽

Alpha Titanium ◽

Cold Rolled ◽

Kinetics Of ◽

Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

Download Full-text

Microstructure studies of tungsten silicide schottky contacts on Gaas

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100126445 ◽

1987 ◽

Vol 45 ◽

pp. 328-329

Author(s):

Yih-Cheng Shih ◽

E. L. Wilkie

Keyword(s):

Thermal Stability ◽

Field Effect Transistors ◽

Schottky Contact ◽

Schottky Contacts ◽

Excellent Thermal Stability ◽

Barrier Heights ◽

Gaas Substrates ◽

Film Adhesion ◽

Threshold Voltages ◽

Thermal Stability Of

Tungsten silicides (WSix) have been successfully used as the gate materials in self-aligned GaAs metal-semiconductor-field- effect transistors (MESFET). Thermal stability of the WSix/GaAs Schottky contact is of major concern since the n+ implanted source/drain regions must be annealed at high temperatures (∼ 800°C). WSi0.6 was considered the best composition to achieve good device performance due to its low stress and excellent thermal stability of the WSix/GaAs interface. The film adhesion and the uniformity in barrier heights and ideality factors of the WSi0.6 films have been improved by depositing a thin layer of pure W as the first layer on GaAs prior to WSi0.6 deposition. Recently WSi0.1 has been used successfully as the gate material in 1x10 μm GaAs FET's on the GaAs substrates which were sputter-cleaned prior to deposition. These GaAs FET's exhibited uniform threshold voltages across a 51 mm wafer with good film adhesion after annealing at 800°C for 10 min.

Download Full-text