The Ordered Phase Formation in Ti-Al-Ga Alloys

1970 ◽  
Vol 28 ◽  
pp. 440-441
Author(s):  
Shiro Fujishiro ◽  
Harold L. Gegel
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Titanium Alloys ◽  
Growth Kinetics ◽  
Stoichiometric Composition ◽  
Good Potential ◽  
Alpha Titanium ◽  
Cold Rolled ◽  
Kinetics Of ◽  
Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

Study of Grain Growth Kinetics in Submicrocrystalline Armco-Iron

2007 ◽  
Vol 550 ◽  
pp. 465-470 ◽  
Author(s):  
A.N. Aleshin ◽  
Alex M. Arsenkin ◽  
Sergey V. Dobatkin
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Low Temperature ◽  
Grain Growth ◽  
Growth Kinetics ◽  
Armco Iron ◽  
High Temperature Annealing ◽  
Grain Growth Kinetics ◽  
Submicrocrystalline Materials ◽  
Thermal Stability Of

The paper is devoted to the problem of thermal stability of ultra-fine grained (submicrocrystalline) materials prepared by severe plastic deformation. A basis of the paper lies in a fact that there is practically no grain growth in submicrocrystalline materials when annealing temperature is less than 0.35Tm. Reasons of high thermal stability of submicrocrystalline materials at low temperatures are widely discussed in literature. One of them is the affect of triple junction drag on grain boundaries motion. During annealing at a low temperature triple junction drag controls microstructure evolution in submicrocrystalline materials, and this phenomenon can be used to improve their thermal stability at high temperatures. The aim of this paper is to investigate grain growth kinetics in a two-step regime, low temperature and high temperature annealing. The experiments on grain growth were performed in submicrocrystalline Armco-iron fabricated by high pressure torsion. It is established that long-time low temperature pre-annealing reduces the grain growth rate in following high temperature annealing by a factor greater than two.

scholarly journals Isothermal Vulcanization and Non-Isothermal Degradation Kinetics of XNBR/Epoxy/XNBR-g-Halloysite Nanotubes (HNT) Nanocomposites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2872
Author(s):  
Seyed Mohamad Reza Paran ◽  
Ghasem Naderi ◽  
Elnaz Movahedifar ◽  
Maryam Jouyandeh ◽  
Krzysztof Formela ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Degradation Kinetics ◽  
Halloysite Nanotubes ◽  
Butadiene Rubber ◽  
Order Model ◽  
Scanning Calorimetry ◽  
Theoretical Methods ◽  
Vulcanization Kinetics ◽  
Kinetics Of ◽  
Thermal Stability Of

The effect of several concentrations of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the vulcanization and degradation kinetics of XNBR/epoxy compounds were evaluated using experimental and theoretical methods. The isothermal vulcanization kinetics were studied at various temperatures by rheometry and differential scanning calorimetry (DSC). The results obtained indicated that the nth order model could not accurately predict the curing performance. However, the autocatalytic approach can be used to estimate the vulcanization reaction mechanism of XNBR/epoxy/XHNTs nanocomposites. The kinetic parameters related to the degradation of XNBR/epoxy/XHNTs nanocomposites were also assessed using thermogravimetric analysis (TGA). TGA measurements suggested that the grafted nanotubes strongly enhanced the thermal stability of the nanocomposite.

Increased Thermal Stability of Co-silicide Using Co-Ta Alloy Films

2001 ◽  
Vol 670 ◽  
Author(s):  
Min-Joo Kim ◽  
Hyo-Jick Choi ◽  
Dae-Hong Ko ◽  
Ja-Hum Ku ◽  
Siyoung Choi ◽  
...  
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Grain Boundary ◽  
Reaction Rate ◽  
Boundary Migration ◽  
Grain Boundary Migration ◽  
Alloy Films ◽  
Post Annealing ◽  
Alloy Process ◽  
Thermal Stability Of

ABSTRACTThe silicidation reactions and thermal stability of Co silicide formed from Co-Ta/Si systems have been investigated. In case of Co-Ta alloy process, the formation of low resistive CoSi2phase is delayed to about 660°C, as compared to conventional Co/Si system. Moreover, the presence of Ta in Co-Ta alloy films reduces the silicidation reaction rate, resulting in the strong preferential orientation in CoSi2 films. Upon high temperature post annealing in the furnace, the sheet resistance of Co-silicide formed from Co/Si systems increases significantly, while that of Co-Ta/Si systems maintains low. This is due to the formation of TaSi2 at the grain boundaries and surface of Co-silicide films, which prevents the grain boundary migration thereby slowing the agglomeration. Therefore, from our research, increased thermal stability of Co-silicide films was successfully obtained from Co-Ta alloy process.

Kinetics of Growth and Structure of Coatings Obtained on Sandelin Steels in the High-Temperature Galvanizing Process

2013 ◽  
Vol 212 ◽  
pp. 127-132 ◽  
Author(s):  
Henryk Kania
Keyword(s):  
High Temperature ◽  
Growth Kinetics ◽  
Structural Components ◽  
Compact Layer ◽  
Two Phase ◽  
Continuous Layer ◽  
Structure Of Coatings ◽  
Zinc Coatings ◽  
Kinetics Of ◽  
Diffuse Coating

In the paper the author presents the results of tests defining the characteristics of behaviour of Sandelin steel in the high-temperature galvanizing process. The growth kinetics of hot-dip zinc coatings on the substrate of 0.05% Si steel in the temperature range of 540-580°C has been established. The structure of the coatings and their phase composition have been developed and the chemical composition of structural components of the coating has be defined. It has been determined that the coating is composed of a compact layer δ1 and an area of a two-phase mixture of δ1 and Zn. The conducted tests confirmed the presence of phase Γ1 , which does not form a continuous layer but it forms individual precipitates which are irregular in shape. The growth kinetics of the coating indicates that an increase in temperature causes a decrease in the coating thickness, which might prove that dissolving processes prevailed over the processes of diffuse coating growth.

Thermal Breakdown Kinetics of 1-Ethyl-3-Methylimidazolium Ethylsulfate Measured Using Quantitative Infrared Spectroscopy

2017 ◽  
Vol 71 (12) ◽  
pp. 2626-2631 ◽  
Author(s):  
Jeffrey L. Wheeler ◽  
McKinley Pugh ◽  
S. Jake Atkins ◽  
Jason M. Porter
Keyword(s):  
Thermal Stability ◽  
Room Temperature ◽  
Computational Models ◽  
Elevated Temperatures ◽  
Molar Absorptivity ◽  
Ir Absorption ◽  
Optical Cell ◽  
Multiple Samples ◽  
Kinetics Of ◽  
Thermal Stability Of

In this work, the thermal stability of the room temperature ionic liquid (RTIL) 1-ethyl-3-methylimidazolium ethylsulfate ([EMIM][EtSO4]) is investigated using infrared (IR) spectroscopy. Quantitative IR absorption spectral data are measured for heated [EMIM][EtSO4]. Spectra have been collected between 25 ℃ and 100 ℃ using a heated optical cell. Multiple samples and cell pathlengths are used to determine quantitative values for the molar absorptivity of [EMIM][EtSO4]. These results are compared to previous computational models of the ion pair. These quantitative spectra are used to measure the rate of thermal decomposition of [EMIM][EtSO4] at elevated temperatures. The spectroscopic measurements of the rate of decomposition show that thermogravimetric methods overestimate the thermal stability of [EMIM][EtSO4].

Thermal stability of nickel-cobalt multilayer silicide

2005 ◽  
Vol 891 ◽  
Author(s):  
Kil Jin Han ◽  
Yu Jung Cho ◽  
Soon Young Oh ◽  
Yong Jin Kim ◽  
Won Jae Lee ◽  
...  
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Depth Profile ◽  
Ternary Phase ◽  
Nickel Silicide ◽  
Composition Gradient ◽  
Cobalt Silicide ◽  
Nickel Cobalt ◽  
Thermal Stability Of ◽  
Xps Depth Profile

ABSTRACTIn this study, we have investigated the structure of nickel-cobalt silicide to understand its behavior at high temperature. Nickel-cobalt silicide was formed after two-step RTP at 500°C and 700°C respectively. We could observe by TEM that nickel-cobalt silicide consists of a structure which seems to be a Ni-Co-Si ternary phase. No nickel silicide phases and cobalt silicide phases were detected in nickel-cobalt silicide by XRD. From XPS depth profile, we could confirm that there is a cobalt composition gradient along the silicide.

Thermal stability of high-temperature materials. Part 1

2004 ◽  
Vol 45 (5) ◽  
pp. 327-332 ◽  
Author(s):  
V. V. Kolomeitsev ◽  
S. A. Suvorov ◽  
E. F. Kolomeitseva
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
High Temperature Materials ◽  
Thermal Stability Of
Sign in / Sign up

Export Citation Format

Share Document