Fracture Characteristics of AISI D2 Tool Steel at Different Tempering Temperatures Using Acoustic Emission and Fuzzy C-Means Clustering

2013 ◽  
Vol 38 (8) ◽  
pp. 2205-2217 ◽  
Author(s):  
Fotouhi Mohamad ◽  
Teymuri Sindi Cevat ◽  
Ahmadi Mehdi ◽  
Pashmforoush Farzad
Keyword(s):  
Acoustic Emission ◽  
Tool Steel ◽  
Fracture Characteristics ◽  
Fuzzy C Means ◽  
Aisi D2 ◽  
Fuzzy C Means Clustering ◽  
Aisi D2 Tool Steel

Acoustic Emission Methodology to Evaluate the Fracture Toughness in Heat Treated AISI D2 Tool Steel

2012 ◽  
Vol 21 (10) ◽  
pp. 2106-2116 ◽  
Author(s):  
Sajad Mostafavi ◽  
Mohamad Fotouhi ◽  
Abed Motasemi ◽  
Mehdi Ahmadi ◽  
Cevat Teymuri Sindi
Keyword(s):  
Fracture Toughness ◽  
Acoustic Emission ◽  
Tool Steel ◽  
Heat Treated ◽  
Aisi D2 ◽  
Aisi D2 Tool Steel

scholarly journals Multi-pass friction stirred clad welding of dissimilar joined AA6061 aluminium alloy and brass

2018 ◽  
Vol 12 (4) ◽  
pp. 4285-4299
Author(s):  
Nora Osman ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar
Keyword(s):  
Mechanical Properties ◽  
Tool Steel ◽  
Microstructural Analysis ◽  
Welding Process ◽  
Fusion Welding ◽  
Tool Steels ◽  
Aa6061 Aluminium Alloy ◽  
Aisi D2 ◽  
Semi Solid ◽  
Aisi D2 Tool Steel

Tool steels are commonly used to cut metal materials due to their distinctive hardness, resistance to abrasion and deformation. However, tool steels are difficult to be joined using conventional fusion welding process. In this study, a thixotropic property of metal was utilised to butt-join an AISI D2 tool steel by using uncommon direct partial re-melting (DPRM) method. A high frequency of induction heating is used to apply the DPRM method. From the recent study, there are many methods in achieving the globular microstructure with the success of semi-solid joining process. Though, very less information on the microstructural effect of semi-solid joining on the mechanical properties was reported. This study aims to analyse the effect of uniaxial force on the microstructural evolution and mechanical properties of the thixo-joint of D2 tool steel. The microstructural analysis showed the diffusion occurred between the grains of the thixo-joint sample with 2.5 N uniaxial force. The maximum strength of the thixo-joint sample with force was 652 MPa. This was slightly higher than the as-received sample and the thixo-joint sample without force. The average hardness value of the thixo-joint sample was 400 HV due to the transformation of ferrite to the metastable austenite.

scholarly journals Minimization of Distortion in Heat Treated AISI D2 Tool Steel: Mechanism and Distortion Analysis

2018 ◽  
Vol 20 ◽  
pp. 113-118 ◽  
Author(s):  
Tushar Sonar ◽  
Sachin Lomte ◽  
Chandrashekhar Gogte ◽  
V. Balasubramanian
Keyword(s):  
Tool Steel ◽  
Heat Treated ◽  
Distortion Analysis ◽  
Aisi D2 ◽  
Aisi D2 Tool Steel

scholarly journals Analysis of chip formation and cutting forces in end milling AISI D2 tool steel with different cutting tool geometries

2018 ◽  
Vol 178 ◽  
pp. 01016
Author(s):  
Irina Beşliu ◽  
Dumitru Amarandei ◽  
Delia Cerlincă
Keyword(s):  
Cutting Force ◽  
Tool Steel ◽  
Chip Formation ◽  
Cutting Forces ◽  
Cutting Tool ◽  
End Milling ◽  
Great Influence ◽  
Tool Geometry ◽  
Aisi D2 ◽  
Aisi D2 Tool Steel

The purpose of this study was to investigate and establish the correlations between milling tool geometry, cutting conditions, as input factors and the cutting forces variations and chips formation, as output factors when end milling of AISI D2 tool steel. The experiments were carried out using a Taguchi design array. The chip shape and microstructure and cutting force components were analyzed. The results of the study show that the cutting tool geometry has a great influence over segmented chip formation mechanism and cutting force levels.

Optimization of Machining Time and Surface Quality of AISI D2 Tool Steel in WEDM Using Taguchi Methodology and Desirability Analysis

2020 ◽  
Vol 977 ◽  
pp. 27-33
Author(s):  
Carmita Camposeco-Negrete ◽  
Juan de Dios Calderón-Nájera
Keyword(s):  
Surface Roughness ◽  
Tool Steel ◽  
Cutting Parameters ◽  
Machining Time ◽  
Aisi D2 ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Aisi D2 Tool Steel ◽  
Off Time

One of the non-conventional machining processes widely used in the industry is the wire electrical discharge machining (WEDM). This process has many advantages, like the great precision and quality that can be achieved. As well as other manufacturing operations, the success of the process relies on a correct selection of the cutting parameters. The present paper outlines an experimental study to optimize the machining time and the surface roughness in WEDM of AISI D2 tool steel during roughing machining. The Taguchi methodology is used to evaluate the effects and contributions of the pulse-on time, pulse-off time, servo voltage, and wire speed, on the response variables. The desirability method is employed to define a set of cutting parameters that allows reducing both machining time and surface roughness at the same time. The pulse-on time is the most significant factor for reducing the machining time, followed by the servo voltage, the pulse-off time and the wire speed. For surface roughness, the pulse-off time is the factor with the greatest influence over the response variable. The results obtained show that the machining time is reduced by 4.65%, and the surface roughness is diminished by 4.60% when compared with the initial values that are commonly used in the machining of AISI D2 tool steel. Therefore, greater production rates can be achieved without compromising the quality of the machined parts.

Some investigations into machining of AISI D2 tool steel using wire electro discharge machining (WEDM) process

2018 ◽  
Vol 5 (11) ◽  
pp. 24347-24357
Author(s):  
Sujeet Kumar Chaubey ◽  
Shankar Singh ◽  
Abhishek Singh
Keyword(s):  
Tool Steel ◽  
Electro Discharge Machining ◽  
Aisi D2 ◽  
Wedm Process ◽  
Aisi D2 Tool Steel
Sign in / Sign up

Export Citation Format

Share Document