Whisker-reinforced ceramic cutting tool material

Composites ◽  
1994 ◽  
Vol 25 (10) ◽  
pp. 959
Keyword(s):  
Cutting Tool ◽  
Tool Material ◽  
Ceramic Cutting Tool

Lifetime predictions for a ceramic cutting tool material at high temperatures

1987 ◽  
Vol 22 (6) ◽  
pp. 2051-2057 ◽  
Author(s):  
B. Gurumoorthy ◽  
K. Kromp ◽  
F. B. Prinz ◽  
A. C. Bornhauser
Keyword(s):  
High Temperatures ◽  
Cutting Tool ◽  
Tool Material ◽  
Ceramic Cutting Tool

In-situ fabricated TiB2 particle-whisker synergistically toughened Ti(C, N)-based ceramic cutting tool material

2015 ◽  
Vol 28 (2) ◽  
pp. 338-342 ◽  
Author(s):  
Hanlian Liu ◽  
Qiang Shi ◽  
Chuanzhen Huang ◽  
Bin Zou ◽  
Liang Xu ◽  
...  
Keyword(s):  
Cutting Tool ◽  
Tool Material ◽  
Tib2 Particle ◽  
Ceramic Cutting Tool

Wear behavior of Si3N4 ceramic cutting tool material against stainless steel in dry and water-lubricated conditions

1999 ◽  
Vol 25 (4) ◽  
pp. 309-315 ◽  
Author(s):  
Zhao Xingzhong ◽  
Liu Jiajun ◽  
Zhu Baoliang ◽  
Miao Hezhou ◽  
Luo Zhenbi
Keyword(s):  
Stainless Steel ◽  
Cutting Tool ◽  
Wear Behavior ◽  
Tool Material ◽  
Si3n4 Ceramic ◽  
Ceramic Cutting Tool

Cutting Performance of Al2O3/TiC/TiN Nanocomposite Tools

2010 ◽  
Vol 443 ◽  
pp. 318-323 ◽  
Author(s):  
Han Lian Liu ◽  
Chuan Zhen Huang ◽  
Bin Zou
Keyword(s):  
High Speed ◽  
Cutting Tool ◽  
Tool Material ◽  
High Hardness ◽  
Hardened Steel ◽  
Cutting Performance ◽  
Machining Parameters ◽  
Dry Cutting ◽  
Ceramic Cutting Tool ◽  
Multi Phase

A multi-scale and multi-phase nanocomposite ceramic cutting tool material Al2O3/TiC/TiN(LTN) with high comprehensive mechanical properties has been successfully fabricated by means of adding micro-scale TiC and nano-scale TiN particles. The cutting performance and wear mechanisms of this advanced ceramic cutting tool were researched by turning two kinds of hardened steel 40Cr and T10A respectively. Compared with the commercial ceramic tool LT55, LTN showed a superior wear resistance with certain machining parameters. The machining tests indicated that the new materials tool is suitable for continuously dry cutting of hardened steel with high hardness at high speed.

Establishment of the Low Defect Ceramic Cutting Tool Database

2013 ◽  
Vol 589-590 ◽  
pp. 357-360 ◽  
Author(s):  
Chang Bin Zou ◽  
Chuan Zhen Huang ◽  
Bin Zou ◽  
Yu Huan Fei ◽  
Han Lian Liu ◽  
...  
Keyword(s):  
Data Structure ◽  
Cutting Tool ◽  
Tool Material ◽  
Material System ◽  
Chemical Compatibility ◽  
Tool Materials ◽  
Abnormal Growth ◽  
Ceramic Cutting Tool ◽  
Preparation Stage ◽  
Cutting Tool Materials

This paper analyzes the reasons of the defects generation of the ceramic cutting tool materials. The defects in the ceramic cutting tool materials are caused by chemical compatibility and physical mismatch during the designing process, and caused by grain abnormal growth and sintering parameters during the preparation stage. The database of low defect ceramic cutting tool is established and the data structure of the database is described. The users can use the database to design the tool material system through the mode that can reduce the defects.

Sign in / Sign up

Export Citation Format

Share Document