The Effect of Crude Oil–Water Interfacial Properties on Water–Crude Oil Emulsion Stability

Author(s):  
R.J.R. CAIRNS ◽  
D.M. GRIST ◽  
E.L. NEUSTADTER
2015 ◽  
Vol 29 (6) ◽  
pp. 3616-3625 ◽  
Author(s):  
Daniel P. Cherney ◽  
Chunping Wu ◽  
Rachel M. Thorman ◽  
Jessica L. Hegner ◽  
Mohsen S. Yeganeh ◽  
...  

2007 ◽  
Vol 4 (1) ◽  
pp. 66-69 ◽  
Author(s):  
Guo Jixiang ◽  
Li Mingyuan ◽  
Lin Meiqin ◽  
Wu Zhaoliang

2016 ◽  
Vol 9 (1) ◽  
pp. 1-10 ◽  
Author(s):  
Jiaqiang Jing ◽  
Jiatong Tan ◽  
Haili Hu ◽  
Jie Sun ◽  
Peiyu Jing

Transparent model oils are commonly used to study the flow patterns and pressure gradient of crude oil-water flow in gathering pipes. However, there are many differences between the model oil and crude oils. The existing literatures focus on the flow pattern transition and pressure gradient calculation of model oils. This paper compares two most commonly used model oils (white mineral oil and silicon oil) with Xinjiang crude oil from the perspectives of rheological properties, oil-water interfacial tensions, emulsion photomicrographs and demulsification process. It indicates that both the white mineral oil and the crude oils are pseudo plastic fluids, while silicon oil is Newtonian fluid. The viscosity-temperature relationship of white mineral oil is similar to that of the diluted crude oil, while the silicon oil presents a less viscosity gradient with the increasing temperature. The oil-water interfacial tension can be used to evaluate the oil dispersing ability in the water phase, but not to evaluate the emulsion stability. According to the Turbiscan lab and the stability test, the model oil emulsion is less stable than that of crude oil, and easier to present water separation.


2018 ◽  
Author(s):  
Ayman. M Almohsin ◽  
Zainab Alabdulmohsen ◽  
Baojun Bai ◽  
Parthasakha Neogi

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Pengyu Wang ◽  
Wei Wang ◽  
Jing Gong ◽  
Yuanxin Zhou ◽  
Wei Yang

In the study of the foundation of the oil / water wax deposition experiment, the emulsification characteristics of crude oil emulsion with high wax content have gradually become the hot research area. In the current research of emulsification characteristics of oil/water emulsion, the attention has been focused on the study of the effects of water cut, stirring speed, particle size distribution on the viscosity of waxy crude oil emulsion in the experiment, in which heavy oil and simulated oil are adopted as the working fluids. In this study, the emulsion with different water cut and stirred by different speed was prepared under three different temperature conditions, the temperature above the wax appearance temperature (WAT), near the WAT, and below the WAT. The polarization microscope and rotary viscometer were applied to measure the effects of the particle size of the dispersed phase and waxy crystal distribution on the oil/water emulsion viscosity. The results suggest that preparing the temperature for crude oil emulsion with high wax content has an important influence on the emulsion microstructure. This study lays the foundation for further study of oil/water two phase dynamic wax deposition experiments.


2020 ◽  
Vol 10 (4) ◽  
pp. 69-84
Author(s):  
Dr. Mueyyed Akram Arslan ◽  
Dr. Ghassan Burhan Yaqoob

In this study oil-soluble (RP6000 and MAKS-9150) emulsion breakers have been selected for separation of water from Kirkuk / baba (50oC), Khbbaz (40oC) crude oil emulsions and their activity measured using the Bottle test method at different concentration and found the activity of RP6000 demulsified best than MAKS-9150 emulsion breakers. RP6000 separated water (100%) in (15)min., (40)ppm and in (60)min., (20)ppm of demulsified for Kirkuk/ baba Crude oil and for khbbaz Crude oil the (100%) water separation was in (15)min., (80)ppm and in (30)min., (60)ppm and PH effect, salinity, temperature and density of emulsion stability depending on literature were explained for Optimization.


Sign in / Sign up

Export Citation Format

Share Document