Automatic soiling and partial shading assessment on PV modules through RGB images analysis

2022 ◽  
Vol 306 ◽  
pp. 117964
Author(s):  
Robinson Cavieres ◽  
Rodrigo Barraza ◽  
Danilo Estay ◽  
José Bilbao ◽  
Patricio Valdivia-Lefort
Keyword(s):  
Partial Shading ◽  
Pv Modules ◽  
Rgb Images

scholarly journals A Simple Mismatch Mitigating Partial Power Processing Converter for Solar PV Modules

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2308
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Experimental Tests ◽  
Energy Yield ◽  
Power Electronic ◽  
Solar Pv ◽  
Partial Shading ◽  
Loss Analysis ◽  
Pv Systems ◽  
Pv Module ◽  
Pv Modules ◽  
In Series

Partial shading affects the energy harvested from photovoltaic (PV) modules, leading to a mismatch in PV systems and causing energy losses. For this purpose, differential power processing (DPP) converters are the emerging power electronic-based topologies used to address the mismatch issues. Normally, PV modules are connected in series and DPP converters are used to extract the power from these PV modules by only processing the fraction of power called mismatched power. In this work, a switched-capacitor-inductor (SCL)-based DPP converter is presented, which mitigates the non-ideal conditions in solar PV systems. A proposed SCL-based DPP technique utilizes a simple control strategy to extract the maximum power from the partially shaded PV modules by only processing a fraction of the power. Furthermore, an operational principle and loss analysis for the proposed converter is presented. The proposed topology is examined and compared with the traditional bypass diode technique through simulations and experimental tests. The efficiency of the proposed DPP is validated by the experiment and simulation. The results demonstrate the performance in terms of higher energy yield without bypassing the low-producing PV module by using a simple control. The results indicate that achieved efficiency is higher than 98% under severe mismatch (higher than 50%).

scholarly journals Operation of TUT Solar PV Power Station Research Plant under Partial Shading Caused by Snow and Buildings

2013 ◽  
Vol 2013 ◽  
pp. 1-13 ◽  
Author(s):  
Diego Torres Lobera ◽  
Anssi Mäki ◽  
Juha Huusari ◽  
Kari Lappalainen ◽  
Teuvo Suntio ◽  
...  
Keyword(s):  
Measuring System ◽  
Climatic Data ◽  
Building Structures ◽  
Solar Pv ◽  
Research Facility ◽  
Electrical Measurements ◽  
Pv System ◽  
Partial Shading ◽  
Power Characteristics ◽  
Pv Modules

A grid connected solar photovoltaic (PV) research facility equipped with comprehensive climatic and electric measuring systems has been designed and built in the Department of Electrical Engineering of the Tampere University of Technology (TUT). The climatic measuring system is composed of an accurate weather station, solar radiation measurements, and a mesh of irradiance and PV module temperature measurements located throughout the solar PV facility. Furthermore, electrical measurements can be taken from single PV modules and strings of modules synchronized with the climatic data. All measured parameters are sampled continuously at 10 Hz with a data-acquisition system based on swappable I/O card technology and stored in a database for later analysis. The used sampling frequency was defined by thorough analyses of the PV system time dependence. Climatic and electrical measurements of the first operation year of the research facility are analyzed in this paper. Moreover, operation of PV systems under partial shading conditions caused by snow and building structures is studied by means of the measured current and power characteristics of PV modules and strings.

scholarly journals Shadow dispersion of PV Array under variable irradiance for superior power Generation by Magic Square Configuration

2018 ◽  
Vol 7 (1.8) ◽  
pp. 172 ◽  
Author(s):  
G Sreenivasa Reddy ◽  
T Bramhananda Reddy ◽  
M Vijaya Kumar
Keyword(s):  
Power Generation ◽  
Power Loss ◽  
Electrical Power ◽  
Partial Shading ◽  
Magic Square ◽  
Photovoltaic Modules ◽  
Pv Array ◽  
Pv Modules ◽  
Square Configuration ◽  
Comparison Data

The PV array generates smaller amount of the power compared with other electrical power generation components. There are many components that are adversely effected the output of PV array in such components, one is partial shading. Due to this, each module in PV array receives different solar irradiations causes different P-V characteristics of its peak values. This paper presents a pioneering method called as Magic Square configuration has been proposed to enhance the generated power of photovoltaic modules by configuring those are under affect of shade. Thus there is no change of electrical arrangement of PV modules in an array but only the objective location in the total cross tied (TCT) array is rearranged according to the magic square arrangement. Proposed paper gives comparison data with the conventional configuration method and hence the performance is calculated. The proposed technique provides a better solution that how shadow effect on the PV  modules has been reduced and how this shadow is distributed, and not only that also gives an idea  about how the inequality losses due to the partial shading is effectively reduced. The power loss of  various configurations of 3X3 and 4X4 array has been compared. The proposed technique is validated through MATLAB/Simulink environment. 

scholarly journals Outdoor study of partial shading effects on different PV modules technologies

2017 ◽  
Vol 141 ◽  
pp. 81-85 ◽  
Author(s):  
Idriss Hadj Mahammed ◽  
Amar Hadj Arab ◽  
Smail berrah ◽  
Yahia Bakelli ◽  
Messaouda Khennene ◽  
...  
Keyword(s):  
Partial Shading ◽  
Pv Modules ◽  
Shading Effects

scholarly journals Power Enhancement from Solar PV Array Topologies under Partial Shading Condition

2018 ◽  
Vol 10 (01) ◽  
pp. 33-40
Author(s):  
Santosh Kumar Singh ◽  
Anurag Singh Yadav ◽  
Ashutosh Srivastava ◽  
Amarjeet Singh
Keyword(s):  
Maximum Output Power ◽  
Maximum Output ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Partial Shading ◽  
Pv Array ◽  
Power Enhancement ◽  
Pv Modules ◽  
Multiple Load ◽  
Mismatch Effect

In this paper, a detailed study is carried out on the solar photovoltaic (PV) array topologies under various shading patterns. The aim of this study is to investigate the mismatch effect losses in PV modules for non uniform irradiations. The shading causes not only power losses, but also non-linearity of P-V characteristics. Under partial shaded conditions, the P-V and I-V characteristics exhibit extreme non-linearity along with multiple load maxima. In this paper, the investigations of the optimal layout of PV modules in a PV array are worked out to provide maximum output power under various shaded conditions. Three type of solar PV array topologies e.g. Series-parallel (SP), Total cross tied (TCT) and Bridge link (BL) are considered for various typesof shaded patterns. The modeling of solar PV array for various types of topologies is done in MATLAB/Simulink environment. The extensive results have been taken on these topologies for partial shading patterns and analyzed, which proves the TCT topology performance is better as compared to other topologies for most of the shading patterns.

scholarly journals Detection of Hotspots and Performance Deteriotations in PV Modules under Partial Shading Conditions Using Infrared Thermography

2020 ◽  
Vol 2 (1) ◽  
pp. 71
Author(s):  
Onyinye Emmanuella Ikejiofor ◽  
Yeboah Emmanuel Asuamah ◽  
Howard O. Njoku ◽  
Samuel O. Enibe
Keyword(s):  
Infrared Thermography ◽  
Thermal Imager ◽  
Ambient Conditions ◽  
Partial Shading ◽  
Surface Areas ◽  
Current Voltage ◽  
Pv Modules ◽  
Thermal Patterns ◽  
And Performance ◽  
Infrared Thermal Imager

Operating photovoltaic (PV) modules are frequently shaded by nearby structures, vegetation, droppings, etc., and this reduces the effective incident solar radiation received by the modules. Shading also reduces the power output of PV modules and, under certain conditions, causes the formation of hotspots. In this study, a wide variety of partial shading scenarios were investigated to evaluate their effects on the output current, voltage and efficiencies, and hotspot formation in mono-crystalline and poly-crystalline PV modules operating under the ambient conditions experienced in Nsukka, Nigeria. Sixteen shading cases were considered, including 20%, 40%, 60% and 80% of the modules’ surface areas shaded parallel to the long sides, parallel to the short sides, diagonally and randomly. Test ambient conditions, module outputs and surface thermal patterns were simultaneously monitored using a digital solarimeter, multimeter and infrared thermal imager, respectively. The outputs of the modules decreased to almost zero when as little as 40% of the module surfaces were shaded, with the reductions in performance being more severe in the mono-crystalline modules than in the poly-crystalline modules. The infrared thermography revealed the thermal patterns under the different shading conditions and showed that the random shading of the modules was the most likely to result in hotspots.

scholarly journals Thermographic and electrical characterization of a photovoltaic panel under partial shading conditions: a case study

ACTA IMEKO ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 93
Author(s):  
Giovanni Bucci ◽  
Fabrizio Ciancetta ◽  
Edoardo Fiorucci ◽  
Antonio Delle Femine
Keyword(s):  
Electrical Characterization ◽  
Testing Procedure ◽  
Pv System ◽  
Partial Shading ◽  
Photovoltaic Panel ◽  
Pv Module ◽  
Pv Modules ◽  
Consequent Reduction

<p class="Abstract">Shading is one of the most critical factors that produces a reduction in power in photovoltaic (PV) modules. The main causes of shading are related to cloud cover; local specificity; natural characteristics; building and other civil works; and the presence of the PV system itself. A reduction in overall radiation produces a consequent reduction in electric power. Another more problematic effect is associated with the partial shading of the PV modules. The shaded cell behaves as a load, dissipating energy and increasing its temperature. This effect can involve irreversible changes to the PV module, with a decrease in performance that can even cause the destruction of the shaded cell.</p><p>The main aim of this work is the development of a testing procedure for the performance evaluation of commercial PV modules in the presence of partial shading on one cell. Tests were carried out using thermographic and electric measurements and by varying the shading levels according to IEC standards. Shading up to total darkening is achieved by means of a number of filters that reduce the direct solar irradiance.</p><p>As a case study, a complete characterisation of a 180 Wp polycrystalline PV module was performed according to the proposed testing procedure, showing that high temperatures can be measured on the shaded PV module surface even if only 50 % of the surface of one cell of the PV module is darkened.</p>

scholarly journals Numerical Modeling, Simulation and Evaluation of Conventional and Hybrid Photovoltaic Modules Interconnection Configurations under Partial Shading Conditions

2021 ◽  
Author(s):  
Faisal Saeed ◽  
Haider Ali Tauqeer ◽  
Hasan Erteza Gelani ◽  
Muhammad Hassan Yousuf
Keyword(s):  
Power Loss ◽  
Simulation Analysis ◽  
Maximum Power ◽  
Power Losses ◽  
Partial Shading ◽  
Power Characteristics ◽  
Pv Array ◽  
Pv Modules ◽  
In Series ◽  
Simulation And Evaluation

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

Sign in / Sign up

Export Citation Format

Share Document