Comparative study on steady and unsteady conjugate heat transfer analysis of a high pressure turbine blade

2016 ◽  
Vol 99 ◽  
pp. 765-775 ◽  
Author(s):  
Sunwoo Hwang ◽  
Changmin Son ◽  
Doyoung Seo ◽  
Dong-Ho Rhee ◽  
Bongjun Cha
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Comparative Study ◽  
Turbine Blade ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Analysis ◽  
High Pressure Turbine

Optimization of a high pressure turbine blade tip cavity with conjugate heat transfer analysis

2016 ◽  
Vol 30 (12) ◽  
pp. 5529-5538 ◽  
Author(s):  
Jinuk Kim ◽  
Young Seok Kang ◽  
Dongwha Kim ◽  
Jihyeong Lee ◽  
Bong Jun Cha ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Turbine Blade ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Analysis ◽  
High Pressure Turbine ◽  
Blade Tip

scholarly journals Erratum to “Optimization of a high pressure turbine blade tip cavity with conjugate heat transfer analysis”

2017 ◽  
Vol 31 (1) ◽  
pp. 479-479
Author(s):  
Jinuk Kim ◽  
Young Seok Kang ◽  
Dongwha Kim ◽  
Jihyeong Lee ◽  
Bong Jun Cha ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Turbine Blade ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Analysis ◽  
High Pressure Turbine ◽  
Blade Tip

Clocking Effects of Inlet Non-Uniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side while the leading edge is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and high-pressure vanes are then investigated considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first one where hot spot and swirl core are aligned with passage and the second one where they are aligned with the leading edge. Comparisons between metal temperature distributions obtained from conjugate heat transfer simulations are performed evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The leading edge aligned configuration is resulted to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage aligned case. A strong sensitivity of both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

Conjugate Heat Transfer Analysis to Assess Overall Cooling Effectiveness of High Pressure Turbine Nozzle With Optimized Film Cooling Hole Arrangements

2019 ◽  
Author(s):  
Young Seok Kang ◽  
Dong-Ho Rhee ◽  
Sanga Lee ◽  
Bong Jun Cha
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Analysis ◽  
Internal Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Baseline Design ◽  
Pressure Surface

Abstract Conjugate heat transfer analysis method has been highlighted for predicting heat exchange between fluid domain and solid domain inside high-pressure turbines, which are exposed to very harsh operating conditions. Then it is able to assess the overall cooling effectiveness considering both internal cooling and external film cooling at the cooled turbine design step. In this study, high-pressure turbine nozzles, which have three different film cooling holes arrangements, were numerically simulated with conjugate heat transfer analysis method for predicting overall cooling effectiveness. The film cooling holes distributed over the nozzle pressure surface were optimized by minimizing the peak temperature, temperature deviation. Additional internal cooling components such as pedestals and rectangular rib turbulators were modeled inside the cooling passages for more efficient heat transfer. The real engine conditions were given for boundary conditions to fluid and solid domains for conjugate heat transfer analysis. Hot combustion gas properties such as specific heat at constant pressure and other transport properties were given as functions of temperature. Also, the conductivity of Inconel 718 was also given as a function of temperature to solve the heat equation in the nozzle solid domain. Conjugate heat transfer analysis results showed that optimized designs showed better cooling performance, especially on the pressure surface due to proper staggering and spacing hole-rows compared to the baseline design. The overall cooling performances were offset from the adiabatic film cooling effectiveness. Locally concentrated heat transfer and corresponding high cooling effectiveness region appeared where internal cooling effects were overlapped in the optimized designs. Also, conjugate heat transfer analysis results for the optimized designs showed more uniform contours of the overall cooling effectiveness compared to the baseline design. By varying the coolant mass flow rate, it was observed that pressure surface was more sensitive to the coolant mass flow rate than nozzle leading edge stagnation region and suction surface. The CHT results showed that optimized designs to improve the adiabatic film cooling effectiveness also have better overall cooling effectiveness.

Three Dimensional Heat Transfer Analysis of High Pressure Turbine Blade

2009 ◽  
Author(s):  
A. Sipatov ◽  
L. Gomzikov ◽  
V. Latyshev ◽  
N. Gladysheva
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
High Pressure ◽  
Rotor Blade ◽  
Computational Analysis ◽  
Three Dimensional ◽  
Heat Transfer Analysis ◽  
Aircraft Engines ◽  
Turbine Stage ◽  
High Pressure Turbine

The present tendency of creating new aircraft engines with a higher level of fuel efficiency leads to the necessity to increase gas temperature at a high pressure turbine (HPT) inlet. To design such type of engines, the improvement of accuracy of the computational analysis is required. According to this the numerical analysis methods are constantly developing worldwide. The leading firms in designing aircraft engines carry out investigations in this field. However, this problem has not been resolved completely yet because there are many different factors affecting HPT blade heat conditions. In addition in some cases the numerical methods and approaches require tuning (for example to predict laminar-turbulent transition region or to describe the interaction of boundary layer and shock wave). In this work our advanced approach of blade heat condition numerical estimation based on the three-dimensional computational analysis is presented. The object of investigation is an advanced aircraft engine HPT first stage blade. The given analysis consists of two interrelated parts. The first part is a stator-rotor interaction modeling of the investigated turbine stage (unsteady approach). Solving this task we devoted much attention to modeling unsteady effects of stator-rotor interaction and to describing an influence of applied inlet boundary conditions on the blade heat conditions. In particular, to determine the total pressure, flow angle and total temperature distributions at the stage inlet we performed a numerical modeling of the combustor chamber of the investigated engine. The second part is a flow modeling in the turbine stage using flow parameters averaging on the stator-rotor interface (steady approach). Here we used sufficiently finer grid discretization to model all perforation holes on the stator vane and rotor blade, endwalls films in detail and to apply conjugate heat transfer approach for the rotor blade. Final results were obtained applying the results of steady and unsteady approaches. Experimental data of the investigated blade heat conditions are presented in the paper. These data were obtained during full size experimental testing the core of the engine and were collected using two different type of experimental equipment: thermocouples and thermo-crystals. The comparison of experimental data and final results meets the requirements of our investigation.

Mesh Generation for Conjugate Heat Transfer Analysis of a Cooled High Pressure Turbine Stage

2008 ◽  
Author(s):  
Colinda Goormans-Francke ◽  
Guy Carabin ◽  
Charles Hirsch
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Mesh Generation ◽  
Conjugate Heat Transfer ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Flow Solver ◽  
Rib Turbulators ◽  
Structured Mesh ◽  
Grid Points

The presented work demonstrates the feasibility of quasi-automatic structured mesh generation for all details in the complex cooling system of an industrial high pressure turbine stage, as required by advanced Conjugate Heat Transfer (CHT) simulations. The grid generation software has been adapted in order to quasi-automatically mesh typical cooling configurations such as cooling passages, basins, inserts, solid bodies, cooling holes, slots, and rib turbulators. A multi-domain structured mesh with about 154 million grid points and 12,316 blocks has been generated for the turbine stage. It includes 1,000 cooling holes, over 250 rib turbulators and 150 pin fins for the turbine stage. In order to verify the CFD response to the grid properties, simulations were performed as a first step on the coarse grid level (of 21.8 million grid points) using the 3D flow solver package FINE™/Turbo. The conductivity equation was solved for the solid part of the computational domain using the same temporal discretization scheme as for the flow solver. Parallel, coupled fluid/solid calculations using the k-ε turbulence model were performed on three different configurations: nozzle guide vane alone, rotor-blade alone, and full stage. These results show the feasibility of this approach to mesh generation for use in CHT modeling of the complex configuration of cooled turbine stages.

Sign in / Sign up

Export Citation Format

Share Document