Flexible, conductive, and highly pressure-sensitive graphene-polyimide foam for pressure sensor application

2018 ◽  
Vol 164 ◽  
pp. 187-194 ◽  
Author(s):  
Jiayi Yang ◽  
Yusheng Ye ◽  
Xiaoping Li ◽  
Xiaozhou Lü ◽  
Renjie Chen
2020 ◽  
Vol 10 (8) ◽  
pp. 2877 ◽  
Author(s):  
Gaeul Kim ◽  
Chi Cuong Vu ◽  
Jooyong Kim

Today, e-textiles have become a fundamental trend in wearable devices. Fabric pressure sensors, as a part of e-textiles, have also received much interest from many researchers all over the world. However, most of the pressure sensors are made of electronic fibers and composed of many layers, including an intermediate layer for sensing the pressure. This paper proposes the model of a single layer pressure sensor with electrodes and conductive fibers intertwined. The plan dimensions of the fabricated sensors are 14 x 14 mm, and the thickness is 0.4 mm. The whole area of the sensor is the pressure-sensitive point. As expected, results demonstrate an electrical resistance change from 283 Ω at the unload pressure to 158 Ω at the load pressure. Besides, sensors have a fast response time (50 ms) and small hysteresis (5.5%). The hysteresis will increase according to the pressure and loading distance, but the change of sensor loading distance is very small. Moreover, the single-layer pressure sensors also show high durability under many working cycles (20,000 cycles) or washing times (50 times). The single-layer pressure sensor is very thin and more flexible than the multi-layer pressure sensor. The structure of this sensor is also expected to bring great benefits to wearable technology in the future.


Nanoscale ◽  
2018 ◽  
Vol 10 (22) ◽  
pp. 10691-10698 ◽  
Author(s):  
Zhihui Wang ◽  
Ling Zhang ◽  
Jin Liu ◽  
Hao Jiang ◽  
Chunzhong Li

Flexible pressure sensors with interlocked hemispheric microstructures are prepared by a novel breath figure strategy. The subtle microstructure remarkably improves the sensitivity and pressure sensing range of the pressure sensor.


2017 ◽  
Vol 31 (05) ◽  
pp. 1750046
Author(s):  
Wu Zhou ◽  
Dong Wang ◽  
Huijun Yu ◽  
Bei Peng

Rectangular diaphragm is commonly used as a pressure sensitive component in MEMS pressure sensors. Its deformation under applied pressure directly determines the performance of micro-devices, accurately acquiring the pressure–deflection relationship, therefore, plays a significant role in pressure sensor design. This paper analyzes the deflection of an isotropic rectangular diaphragm under combined effects of loads. The model is regarded as a clamped plate with full surface uniform load and partially uniform load applied on its opposite sides. The full surface uniform load stands for the external measured pressure. The partial load is used to approximate the opposite reaction of the silicon island which is planted on the diaphragm to amplify the deformation displacement, thus to improve the sensitivity of the pressure sensor. Superposition method is proposed to calculate the diaphragm deflections. This method considers separately the actions of loads applied on the simple supported plate and moments distributed on edges. Considering the boundary condition of all edges clamped, the moments are constructed to eliminate the boundary rotations caused by lateral load. The diaphragm’s deflection is computed by superposing deflections which produced by loads applied on the simple supported plate and moments distributed on edges. This method provides higher calculation accuracy than Galerkin variational method, and it is used to analyze the influence factors of the diaphragm’s deflection, includes aspect ratio, thickness and the applied force area of the diaphragm.


2021 ◽  
Vol 31 (12) ◽  
pp. 124002
Author(s):  
Jie Yu ◽  
Yulan Lu ◽  
Deyong Chen ◽  
Junbo Wang ◽  
Jian Chen ◽  
...  

Abstract High-pressure sensors enable expansive demands in ocean sciences, industrial controls, and oil explorations. Successful sensor realized in piezoresistive high-pressure sensors which suffer from the key issue of compromised accuracies due to serious temperature drifts. Herein, this paper presents a high accuracy resonant high-pressure sensor with the pressure range of 70 MPa. Different from conventional resonant high-pressure sensor, the developed sensor utilized a dual-resonator-cavity design to minimize temperature disturbances and improve the pressure sensitivities. Besides, four circle cavities were used to maintain a high vacuum level for resonators after anodic bonding process. In details, Dual resonators, which is parallelly placed in the tensile and compressive stresses areas of a rectangular pressure sensitive diaphragm, are separated vacuum-packaged in the parallel dual cavities. Thus, pressure under measurement bends the pressure sensitive diaphragm, producing an increased pressure sensitivity and a decreased temperature sensitivity by the differential outputs of the dual resonators. Parameterized mathematical models of the sensor were established and the parameters of the models were optimized to adjust the pressure sensitivities and the temperature sensitivities of the sensor. Simplified deep reactive ion etching was used to form the sensing structure of the sensor and only once anodic bonding was used to form vacuum packaging for the dual resonators. Experimental results confirmed that the Q values of the resonators were higher than 32 000. Besides, the temperature sensitivity of the sensor was reduced from 44 Hz °C−1 (494 ppm °C−1) to 1 Hz °C−1 (11 ppm °C−1) by the differential outputs of the dual resonators in the temperature range of −10 °C–60 °C under the pressure of 1000 kPa. In addition, the accuracy of the sensor was better than 0.02% FS within the pressure range of 110–6500 kPa and the temperature range of −10 °C–60 °C by using a polynomial algorithm.


2016 ◽  
Vol 121 (11) ◽  
pp. 7775-7789 ◽  
Author(s):  
Francesco Chierici ◽  
Giovanni Iannaccone ◽  
Luca Pignagnoli ◽  
Sergio Guardato ◽  
Marina Locritani ◽  
...  

2001 ◽  
Vol 45 (6) ◽  
pp. 997-1001 ◽  
Author(s):  
Irina Kleps ◽  
Anca Angelescu ◽  
Narcis Samfirescu ◽  
Adriana Gil ◽  
Antonio Correia

2011 ◽  
Vol 171 (1) ◽  
pp. 38-42 ◽  
Author(s):  
Juris Zavickis ◽  
Maris Knite ◽  
Gatis Podins ◽  
Artis Linarts ◽  
Raimonds Orlovs

Author(s):  
Ab Rahman Marlinda ◽  
Nurul Hazierah Kamaruddin ◽  
Abd Wahab Fadilah ◽  
Mardhiah Said ◽  
Nor Aliya Hamizi ◽  
...  

Small ◽  
2019 ◽  
Vol 15 (45) ◽  
pp. 1903487 ◽  
Author(s):  
Zhen Sang ◽  
Kai Ke ◽  
Ica Manas‐Zloczower

Sign in / Sign up

Export Citation Format

Share Document