Effect of variable axial load on seismic behaviour of reinforced concrete columns

2022 ◽  
Vol 250 ◽  
pp. 113388
Author(s):  
Bingyan Wu ◽  
Guangjun Sun ◽  
Hongjing Li ◽  
Shengyu Wang
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Concrete Columns ◽  
Seismic Behaviour ◽  
Reinforced Concrete Columns

scholarly journals Behavior of Columns Confined With FRP Fabrics under Repeated Lateral Loads

2019 ◽  
pp. 1-19
Author(s):  
Hesham A. Haggag ◽  
Nagy F. Hanna ◽  
Ghada G. Ahmed
Keyword(s):  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Axial Load ◽  
Axial Loading ◽  
Concrete Columns ◽  
Fiber Reinforced Polymers ◽  
Lateral Loads ◽  
Reinforced Concrete Columns ◽  
Reinforced Polymers ◽  
Axial Capacity

The axial strength of reinforced concrete columns is enhanced by wrapping them with Fiber Reinforced Polymers, FRP, fabrics.  The efficiency of such enhancement is investigated for columns when they are subjected to repeated lateral loads accompanied with their axial loading.  The current research presents that investigation for Glass and Carbon Fiber Reinforced Polymers (GFRP and CFRP) strengthening as well.  The reduction of axial loading capacity due to repeated loads is evaluated. The number of applied FRP plies with different types (GFRP or CFRP) are considered as parameters in our study. The study is evaluated experimentally and numerically.  The numerical investigation is done using ANSYS software. The experimental testing are done on five half scale reinforced concrete columns.  The loads are applied into three stages. Axial load are applied on specimen in stage 1 with a value of 30% of the ultimate column capacity. In stage 2, the lateral loads are applied in repeated manner in the existence of the vertical loads.  In the last stage the axial load is continued till the failure of the columns. The final axial capacities after applying the lateral action, mode of failure, crack patterns and lateral displacements are recorded.   Analytical comparisons for the analyzed specimens with the experimental findings are done.  It is found that the repeated lateral loads decrease the axial capacity of the columns with a ratio of about (38%-50%).  The carbon fiber achieved less reduction in the column axial capacity than the glass fiber.  The column confinement increases the ductility of the columns under the lateral loads.

SEISMIC PERFORMANCE OF GFRP-RC RECTANGULAR COLUMNS: NUMERICAL STUDY

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Ehab El-Salakawy ◽  
Fangxin Ye ◽  
Yasser Mostafa Selmy
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Axial Load ◽  
Numerical Study ◽  
Concrete Strength ◽  
Weight Ratio ◽  
Concrete Columns ◽  
Load Level ◽  
Reinforced Concrete Columns ◽  
Rectangular Columns

Composite materials like glass fiber-reinforced polymer (GFRP) is becoming widely acceptable to be used as a reinforcing material due to its high ultimate tensile strength-to-weight ratio and excellent resistance to corrosion. However, the seismic behavior of GFRP-reinforced concrete columns has not been fully investigated yet. This paper presents the results of a numerical analysis of full-size GFRP-RC rectangular columns under cyclic loading. The simulated column depicts the lower part of a building column between the foundation and the point of contra-flexure at the mid-height of the column. GFRP reinforcement properties and concrete modeling based on fracture energy have been incorporated in the numerical model. Experimental validation has been used to examine the accuracy of the constructed finite element models (FEMs) using a commercially available software. The validated FEM was used to perform a parametric study, considering several concrete strength values and axial load levels, to study its influence on the performance of the GFRP-reinforced concrete columns under cyclic loading. It was concluded that the hysteretic dissipation capacity deteriorates under high axial load level due to severe softening of the concrete. The FE results showed a substantial improvement of the lateral load-carrying capacities by increasing concrete compressive strength.

scholarly journals Gravity Load Collapse Behavior of Nonengineered Reinforced Concrete Columns

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Chichaya Boonmee ◽  
Kittipoom Rodsin ◽  
Krissachai Sriboonma
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Axial Load ◽  
Concrete Columns ◽  
Poor Quality ◽  
Load Level ◽  
Longitudinal Reinforcement ◽  
Reinforced Concrete Columns ◽  
Gravity Load ◽  
Collapse Behavior

This paper aims at investigating gravity load collapse behavior of extremely poor quality reinforced concrete columns under cyclic loading. Such columns were usually constructed by local people and may not be designed to meet any of the standards. It was found that their concrete strength may be as low as 5 MPa and the amount of longitudinal reinforcement may be lower than 1%. This type of column is deliberately defined as “nonengineered reinforced concrete column,” or NRCC. During earthquake, the gravity load collapse of the NRCC columns caused a large number of death tolls around the world. In this study, four columns as representative of existing NRCC were tested under cyclic loading. The compressive strength of concrete in order of 5 MPa was used to be representative of columns with poor quality concrete. Two axial load levels of 6 and 18 tons were used to study the influence of axial load level on maximum drift at gravity load collapse. To investigate the effect of bar types on drift capacity, 9 mm round bars were used in two specimens and 12 mm deformed bars were used for the rest of the specimens. The maximum drift before gravity load collapse was very dependent on the axial load level. The maximum drift of the specimens subjected to high axial load (18 tons) was extremely low at approximately 1.75% drifts. The use of deformed bars (associated with larger amount of longitudinal reinforcement) caused the damage to severely dissipate all over the height of the columns. Such damage caused columns to collapse at a lower drift compared to those using round bars. Finally, the plastic hinge model was used to predict the maximum drift of the low strength columns. It was found that the model overly underestimates the drift at gravity load collapse.

scholarly journals Investigation of Parameters Affecting the Equivalent Yield Curvature of Reinforced Concrete Columns

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1594
Author(s):  
Umut Hasgul
Keyword(s):  
Reinforced Concrete ◽  
Cross Section ◽  
Axial Load ◽  
Concrete Columns ◽  
Load Level ◽  
Combined Effects ◽  
Reinforced Concrete Columns ◽  
Independent Effects ◽  
Equivalent Yield ◽  
Section Dimension

In this study, the response quantities affecting the equivalent yield curvature, which is important in the deformation-based seismic design and assessment of structural systems, are investigated for reinforced concrete columns with a square cross-section. In this context, the equivalent yield curvatures were determined by conducting moment–curvature analyses on various column models, in which the axial load level, cross-section dimension, longitudinal reinforcement ratio, and concrete compression strength were changed parametrically, and the independent and/or combined effects of the relevant parameters were discussed. Depending on the axial load levels of P/Agfc′ < 0.3, P/Agfc′ = 0.3, and P/Agfc′ > 0.3 for the considered columns, the yielding of reinforcement, yielding of reinforcement and/or concrete crushing, and concrete crushing governed the yield conditions, respectively. It can be noted that the cross-section dimension and axial load level became the primary parameters. Even though the independent effects with regard to particular parameters remained at minimal levels, the combined effects of them with the axial load became important in terms of the equivalent yield curvature.

Seismic Evaluation of Existing Reinforced Concrete Building Columns

1996 ◽  
Vol 12 (4) ◽  
pp. 715-739 ◽  
Author(s):  
Abraham C. Lynn ◽  
Jack P. Moehle ◽  
Stephen A. Mahin ◽  
William T. Holmes
Keyword(s):  
Reinforced Concrete ◽  
Axial Load ◽  
Lateral Displacement ◽  
Concrete Columns ◽  
Vertical Load ◽  
Seismic Evaluation ◽  
Severe Damage ◽  
Reinforced Concrete Columns ◽  
Concrete Building ◽  
Constant Axial Load

Past earthquakes have emphasized the vulnerability of reinforced concrete columns having details typical of those built before the mid-1970's. These columns are susceptible to axial-flexural, shear, and bond failures, which subsequently may lead to severe damage or collapse of the building. Research was undertaken to investigate the lateral and vertical load-resisting behavior of reinforced concrete columns typical of pre-1970's construction. Eight full-scale specimens were constructed and were loaded with constant axial load and increasing cyclic lateral displacement increments until failure. Test data are presented and compared with behavior estimated by using various evaluation methods.

Sign in / Sign up

Export Citation Format

Share Document